|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Unspecified Transmit Phase C error
I have a new installation of HylaFAX v4.1.3 on Redhat 7.2. The modem is a
Cirrus Logic MD55xx. I am able to receive faxes but when I tried a test
transmission I got an Unspecified Transmit Phase C error, giving up after 3
tries.
Here is the log:
Oct 02 18:44:39.80: [ 2127]: SESSION BEGIN 00000008 17028378027
Oct 02 18:44:39.80: [ 2127]: HylaFAX (tm) Version 4.1.3
Oct 02 18:44:39.80: [ 2127]: SEND FAX: JOB 1 DEST 8378027 COMMID 00000008
DEVICE '/dev/ttyS0'
Oct 02 18:44:39.80: [ 2127]: DELAY 75 ms
Oct 02 18:44:39.88: [ 2127]: DELAY 2600 ms
Oct 02 18:44:42.48: [ 2127]: <-- [4:ATZ\r]
Oct 02 18:44:42.59: [ 2127]: --> [2:OK]
Oct 02 18:44:42.59: [ 2127]: DELAY 3000 ms
Oct 02 18:44:45.59: [ 2127]: <-- [5:ATE0\r]
Oct 02 18:44:45.65: [ 2127]: --> [4:ATE0]
Oct 02 18:44:45.65: [ 2127]: --> [2:OK]
Oct 02 18:44:45.65: [ 2127]: <-- [5:ATV1\r]
Oct 02 18:44:45.71: [ 2127]: --> [2:OK]
Oct 02 18:44:45.71: [ 2127]: <-- [5:ATQ0\r]
Oct 02 18:44:45.77: [ 2127]: --> [2:OK]
Oct 02 18:44:45.77: [ 2127]: <-- [7:ATS0=0\r]
Oct 02 18:44:45.83: [ 2127]: --> [2:OK]
Oct 02 18:44:45.83: [ 2127]: <-- [7:ATS8=2\r]
Oct 02 18:44:45.89: [ 2127]: --> [2:OK]
Oct 02 18:44:45.89: [ 2127]: <-- [8:ATS7=60\r]
Oct 02 18:44:45.96: [ 2127]: --> [2:OK]
Oct 02 18:44:45.96: [ 2127]: <-- [12:AT+FCLASS=1\r]
Oct 02 18:44:46.04: [ 2127]: --> [2:OK]
Oct 02 18:44:46.04: [ 2127]: <-- [5:ATM0\r]
Oct 02 18:44:46.10: [ 2127]: --> [2:OK]
Oct 02 18:44:46.10: [ 2127]: <-- [12:AT+FCLASS=1\r]
Oct 02 18:44:46.28: [ 2127]: --> [2:OK]
Oct 02 18:44:46.28: [ 2127]: DIAL 8378027
Oct 02 18:44:46.28: [ 2127]: <-- [12:ATDT8378027\r]
Oct 02 18:45:16.51: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:18.64: [ 2127]: --> [2:OK]
Oct 02 18:45:18.64: [ 2127]: REMOTE NSF "00 00 0E 00 00 00 96 FF 01 03 00 10
00 02 95 80 08 01 49 02 53 4F 4D 45 52 53 20 43 4F 4E 56 45 4E 54 49 4F 03
B1"
Oct 02 18:45:18.64: [ 2127]: NSF remote fax equipment: Panasonic
Oct 02 18:45:18.64: [ 2127]: NSF remote station ID: "SOMERS CONVENTIO"
Oct 02 18:45:18.64: [ 2127]: <-- [9:AT+FRH=3\r]
Oct 02 18:45:18.68: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:19.38: [ 2127]: --> [2:OK]
Oct 02 18:45:19.38: [ 2127]: REMOTE CSI ""
Oct 02 18:45:19.38: [ 2127]: <-- [9:AT+FRH=3\r]
Oct 02 18:45:19.42: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:19.75: [ 2127]: --> [2:OK]
Oct 02 18:45:19.75: [ 2127]: REMOTE best rate 14400 bit/s
Oct 02 18:45:19.75: [ 2127]: REMOTE max page width 1728 pixels in 215 mm
Oct 02 18:45:19.75: [ 2127]: REMOTE max unlimited page length
Oct 02 18:45:19.75: [ 2127]: REMOTE best vres 7.7 line/mm
Oct 02 18:45:19.75: [ 2127]: REMOTE best format 2-D MR
Oct 02 18:45:19.75: [ 2127]: REMOTE best 20 ms/scanline
Oct 02 18:45:19.75: [ 2127]: USE 14400 bit/s
Oct 02 18:45:19.75: [ 2127]: USE 20 ms/scanline
Oct 02 18:45:19.75: [ 2127]: SEND file "docq/doc1.ps;31"
Oct 02 18:45:19.75: [ 2127]: USE page width 1728 pixels in 215 mm
Oct 02 18:45:19.75: [ 2127]: USE unlimited page length
Oct 02 18:45:19.75: [ 2127]: USE 7.7 line/mm
Oct 02 18:45:19.75: [ 2127]: USE 1-D MR
Oct 02 18:45:19.75: [ 2127]: SEND training at v.17 14400 bit/s
Oct 02 18:45:19.75: [ 2127]: <-- [9:AT+FTH=3\r]
Oct 02 18:45:19.80: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:19.80: [ 2127]: <-- data [23]
Oct 02 18:45:19.80: [ 2127]: <-- data [2]
Oct 02 18:45:21.04: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:21.04: [ 2127]: <-- data [6]
Oct 02 18:45:21.04: [ 2127]: <-- data [2]
Oct 02 18:45:21.37: [ 2127]: --> [2:OK]
Oct 02 18:45:21.37: [ 2127]: <-- [9:AT+FTS=7\r]
Oct 02 18:45:21.45: [ 2127]: --> [2:OK]
Oct 02 18:45:21.45: [ 2127]: <-- [11:AT+FTM=145\r]
Oct 02 18:45:21.49: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:21.49: [ 2127]: <-- data [1024]
Oct 02 18:45:21.49: [ 2127]: <-- data [1024]
Oct 02 18:45:21.49: [ 2127]: <-- data [652]
Oct 02 18:45:21.49: [ 2127]: <-- data [2]
Oct 02 18:45:24.29: [ 2127]: --> [2:]
Oct 02 18:45:24.29: [ 2127]: --> [2:OK]
Oct 02 18:45:24.29: [ 2127]: <-- [9:AT+FRH=3\r]
Oct 02 18:45:24.79: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:26.01: [ 2127]: --> [2:OK]
Oct 02 18:45:26.01: [ 2127]: SEND training at v.17 12000 bit/s
Oct 02 18:45:26.01: [ 2127]: <-- [9:AT+FTH=3\r]
Oct 02 18:45:26.06: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:26.06: [ 2127]: <-- data [23]
Oct 02 18:45:26.06: [ 2127]: <-- data [2]
Oct 02 18:45:27.30: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:27.30: [ 2127]: <-- data [6]
Oct 02 18:45:27.30: [ 2127]: <-- data [2]
Oct 02 18:45:27.63: [ 2127]: --> [2:OK]
Oct 02 18:45:27.63: [ 2127]: <-- [9:AT+FTS=7\r]
Oct 02 18:45:27.71: [ 2127]: --> [2:OK]
Oct 02 18:45:27.71: [ 2127]: <-- [11:AT+FTM=121\r]
Oct 02 18:45:27.75: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:27.75: [ 2127]: <-- data [1024]
Oct 02 18:45:27.75: [ 2127]: <-- data [1024]
Oct 02 18:45:27.75: [ 2127]: <-- data [202]
Oct 02 18:45:27.75: [ 2127]: <-- data [2]
Oct 02 18:45:32.33: [ 2127]: --> [2:]
Oct 02 18:45:32.33: [ 2127]: --> [5:ERROR]
Oct 02 18:45:32.33: [ 2127]: MODEM Command error
Oct 02 18:45:32.33: [ 2127]: Problem sending TCF data
Oct 02 18:45:32.33: [ 2127]: <-- [9:AT+FRH=3\r]
Oct 02 18:45:32.38: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:33.18: [ 2127]: --> [2:OK]
Oct 02 18:45:33.18: [ 2127]: TRAINING succeeded
Oct 02 18:45:33.18: [ 2127]: DELAY 75 ms
Oct 02 18:45:33.26: [ 2127]: <-- [11:AT+FTM=122\r]
Oct 02 18:45:33.30: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:33.30: [ 2127]: SEND begin page
Oct 02 18:45:33.31: [ 2127]: <-- data [1027]
Oct 02 18:45:33.31: [ 2127]: <-- data [1027]
Oct 02 18:45:33.31: [ 2127]: <-- data [1024]
Oct 02 18:45:33.31: [ 2127]: <-- data [1024]
Oct 02 18:45:33.31: [ 2127]: <-- data [1024]
Oct 02 18:45:35.30: [ 2127]: <-- data [1024]
Oct 02 18:45:35.31: [ 2127]: <-- data [1024]
Oct 02 18:45:35.31: [ 2127]: <-- data [1025]
Oct 02 18:45:37.30: [ 2127]: <-- data [1024]
Oct 02 18:45:37.30: [ 2127]: <-- data [1024]
Oct 02 18:45:37.30: [ 2127]: <-- data [1024]
Oct 02 18:45:37.30: [ 2127]: <-- data [1025]
Oct 02 18:45:39.30: [ 2127]: <-- data [1037]
Oct 02 18:45:39.30: [ 2127]: <-- data [1025]
Oct 02 18:45:39.30: [ 2127]: <-- data [1024]
Oct 02 18:45:39.30: [ 2127]: <-- data [1024]
Oct 02 18:45:41.29: [ 2127]: <-- data [1030]
Oct 02 18:45:41.29: [ 2127]: <-- data [1033]
Oct 02 18:45:41.30: [ 2127]: <-- data [1034]
Oct 02 18:45:43.29: [ 2127]: <-- data [1026]
Oct 02 18:45:43.29: [ 2127]: <-- data [1028]
Oct 02 18:45:43.29: [ 2127]: <-- data [1027]
Oct 02 18:45:43.29: [ 2127]: <-- data [1024]
Oct 02 18:45:45.29: [ 2127]: <-- data [1024]
Oct 02 18:45:45.29: [ 2127]: <-- data [1024]
Oct 02 18:45:45.29: [ 2127]: <-- data [906]
Oct 02 18:45:45.29: [ 2127]: SENT 26506 bytes of data
Oct 02 18:45:45.29: [ 2127]: SEND 1D RTC
Oct 02 18:45:45.29: [ 2127]: <-- data [29]
Oct 02 18:45:45.29: [ 2127]: <-- data [2]
Oct 02 18:45:45.29: [ 2127]: SEND end page
Oct 02 18:45:48.92: [ 2127]: --> [2:]
Oct 02 18:45:48.92: [ 2127]: --> [2:OK]
Oct 02 18:45:48.92: [ 2127]: <-- [9:AT+FTS=9\r]
Oct 02 18:45:49.01: [ 2127]: --> [2:OK]
Oct 02 18:45:49.01: [ 2127]: SEND send EOP (no more pages or documents)
Oct 02 18:45:49.01: [ 2127]: <-- [9:AT+FTH=3\r]
Oct 02 18:45:49.06: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:49.06: [ 2127]: <-- data [3]
Oct 02 18:45:49.06: [ 2127]: <-- data [2]
Oct 02 18:45:49.79: [ 2127]: --> [2:OK]
Oct 02 18:45:49.79: [ 2127]: <-- [9:AT+FRH=3\r]
Oct 02 18:45:49.98: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:51.19: [ 2127]: --> [2:OK]
Oct 02 18:45:51.19: [ 2127]: SEND recv RTN (retrain negative)
Oct 02 18:45:51.19: [ 2127]: SEND training at v.17 9600 bit/s
Oct 02 18:45:51.19: [ 2127]: <-- [9:AT+FTH=3\r]
Oct 02 18:45:51.24: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:51.24: [ 2127]: <-- data [23]
Oct 02 18:45:51.24: [ 2127]: <-- data [2]
Oct 02 18:45:52.48: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:52.48: [ 2127]: <-- data [6]
Oct 02 18:45:52.48: [ 2127]: <-- data [2]
Oct 02 18:45:52.81: [ 2127]: --> [2:OK]
Oct 02 18:45:52.81: [ 2127]: <-- [9:AT+FTS=7\r]
Oct 02 18:45:52.89: [ 2127]: --> [2:OK]
Oct 02 18:45:52.89: [ 2127]: <-- [10:AT+FTM=97\r]
Oct 02 18:45:52.93: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:52.93: [ 2127]: <-- data [1024]
Oct 02 18:45:52.93: [ 2127]: <-- data [776]
Oct 02 18:45:52.93: [ 2127]: <-- data [2]
Oct 02 18:45:56.08: [ 2127]: --> [2:]
Oct 02 18:45:56.08: [ 2127]: --> [2:OK]
Oct 02 18:45:56.08: [ 2127]: <-- [9:AT+FRH=3\r]
Oct 02 18:45:56.58: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:57.80: [ 2127]: --> [2:OK]
Oct 02 18:45:57.80: [ 2127]: TRAINING succeeded
Oct 02 18:45:57.80: [ 2127]: DELAY 75 ms
Oct 02 18:45:57.88: [ 2127]: <-- [10:AT+FTM=98\r]
Oct 02 18:45:57.92: [ 2127]: --> [7:CONNECT]
Oct 02 18:45:57.92: [ 2127]: SEND begin page
Oct 02 18:45:57.93: [ 2127]: <-- data [1027]
Oct 02 18:45:57.93: [ 2127]: <-- data [1027]
Oct 02 18:45:57.93: [ 2127]: <-- data [1024]
Oct 02 18:45:57.93: [ 2127]: <-- data [1024]
Oct 02 18:45:57.93: [ 2127]: <-- data [1024]
Oct 02 18:45:59.92: [ 2127]: <-- data [1024]
Oct 02 18:45:59.92: [ 2127]: <-- data [1025]
Oct 02 18:45:59.92: [ 2127]: <-- data [1024]
Oct 02 18:46:01.92: [ 2127]: <-- data [1024]
Oct 02 18:46:01.92: [ 2127]: <-- data [1025]
Oct 02 18:46:01.92: [ 2127]: <-- data [1038]
Oct 02 18:46:01.92: [ 2127]: <-- data [1024]
Oct 02 18:46:03.92: [ 2127]: <-- data [1024]
Oct 02 18:46:03.92: [ 2127]: <-- data [1027]
Oct 02 18:46:03.92: [ 2127]: <-- data [1035]
Oct 02 18:46:03.92: [ 2127]: <-- data [1034]
Oct 02 18:46:05.91: [ 2127]: <-- data [1027]
Oct 02 18:46:05.91: [ 2127]: <-- data [1028]
Oct 02 18:46:05.91: [ 2127]: <-- data [1027]
Oct 02 18:46:07.91: [ 2127]: <-- data [1024]
Oct 02 18:46:07.91: [ 2127]: <-- data [1024]
Oct 02 18:46:07.91: [ 2127]: <-- data [933]
Oct 02 18:46:07.91: [ 2127]: SENT 22437 bytes of data
Oct 02 18:46:07.91: [ 2127]: SEND 1D RTC
Oct 02 18:46:07.91: [ 2127]: <-- data [29]
Oct 02 18:46:07.91: [ 2127]: <-- data [2]
Oct 02 18:46:07.91: [ 2127]: SEND end page
Oct 02 18:46:11.86: [ 2127]: --> [2:]
Oct 02 18:46:11.86: [ 2127]: --> [2:OK]
Oct 02 18:46:11.86: [ 2127]: <-- [9:AT+FTS=9\r]
Oct 02 18:46:11.95: [ 2127]: --> [2:OK]
Oct 02 18:46:11.95: [ 2127]: SEND send EOP (no more pages or documents)
Oct 02 18:46:11.95: [ 2127]: <-- [9:AT+FTH=3\r]
Oct 02 18:46:12.00: [ 2127]: --> [7:CONNECT]
Oct 02 18:46:12.00: [ 2127]: <-- data [3]
Oct 02 18:46:12.00: [ 2127]: <-- data [2]
Oct 02 18:46:12.74: [ 2127]: --> [2:OK]
Oct 02 18:46:12.74: [ 2127]: <-- [9:AT+FRH=3\r]
Oct 02 18:46:15.84: [ 2127]: --> [0:]
Oct 02 18:46:15.84: [ 2127]: MODEM <Empty line>
Oct 02 18:46:15.84: [ 2127]: <-- data [1]
Oct 02 18:46:15.85: [ 2127]: --> [2:OK]
Oct 02 18:46:15.85: [ 2127]: SEND send EOP (no more pages or documents)
Oct 02 18:46:15.85: [ 2127]: <-- [9:AT+FTH=3\r]
Oct 02 18:46:15.90: [ 2127]: --> [7:CONNECT]
Oct 02 18:46:15.90: [ 2127]: <-- data [3]
Oct 02 18:46:15.90: [ 2127]: <-- data [2]
Oct 02 18:46:16.64: [ 2127]: --> [2:OK]
Oct 02 18:46:16.64: [ 2127]: <-- [9:AT+FRH=3\r]
Oct 02 18:46:16.83: [ 2127]: --> [7:CONNECT]
Oct 02 18:46:18.04: [ 2127]: --> [2:OK]
Oct 02 18:46:18.04: [ 2127]: SEND recv RTN (retrain negative)
Oct 02 18:46:18.04: [ 2127]: SEND training at v.17 7200 bit/s
Oct 02 18:46:18.04: [ 2127]: <-- [9:AT+FTH=3\r]
Oct 02 18:46:18.09: [ 2127]: --> [7:CONNECT]
Oct 02 18:46:18.09: [ 2127]: <-- data [23]
Oct 02 18:46:18.09: [ 2127]: <-- data [2]
Oct 02 18:46:19.33: [ 2127]: --> [7:CONNECT]
Oct 02 18:46:19.33: [ 2127]: <-- data [6]
Oct 02 18:46:19.33: [ 2127]: <-- data [2]
Oct 02 18:46:19.69: [ 2127]: --> [2:OK]
Oct 02 18:46:19.69: [ 2127]: <-- [9:AT+FTS=7\r]
Oct 02 18:46:19.77: [ 2127]: --> [2:OK]
Oct 02 18:46:19.77: [ 2127]: <-- [10:AT+FTM=73\r]
Oct 02 18:46:19.81: [ 2127]: --> [7:CONNECT]
Oct 02 18:46:19.81: [ 2127]: <-- data [1024]
Oct 02 18:46:19.81: [ 2127]: <-- data [326]
Oct 02 18:46:19.81: [ 2127]: <-- data [2]
Oct 02 18:46:22.96: [ 2127]: --> [2:]
Oct 02 18:46:22.96: [ 2127]: --> [2:OK]
Oct 02 18:46:22.96: [ 2127]: <-- [9:AT+FRH=3\r]
Oct 02 18:46:23.46: [ 2127]: --> [7:CONNECT]
Oct 02 18:46:24.68: [ 2127]: --> [2:OK]
Oct 02 18:46:24.68: [ 2127]: TRAINING succeeded
Oct 02 18:46:24.68: [ 2127]: DELAY 75 ms
Oct 02 18:46:24.76: [ 2127]: <-- [10:AT+FTM=74\r]
Oct 02 18:46:24.80: [ 2127]: --> [7:CONNECT]
Oct 02 18:46:24.80: [ 2127]: SEND begin page
Oct 02 18:46:24.81: [ 2127]: <-- data [1027]
Oct 02 18:46:24.81: [ 2127]: <-- data [1027]
Oct 02 18:46:24.81: [ 2127]: <-- data [1024]
Oct 02 18:46:24.81: [ 2127]: <-- data [1024]
Oct 02 18:46:24.81: [ 2127]: <-- data [1024]
Oct 02 18:46:26.80: [ 2127]: <-- data [1025]
Oct 02 18:46:26.80: [ 2127]: <-- data [1024]
Oct 02 18:46:26.80: [ 2127]: <-- data [1025]
Oct 02 18:46:28.80: [ 2127]: <-- data [1038]
Oct 02 18:46:28.80: [ 2127]: <-- data [1024]
Oct 02 18:46:28.80: [ 2127]: <-- data [1027]
Oct 02 18:46:28.80: [ 2127]: <-- data [1031]
Oct 02 18:46:30.80: [ 2127]: <-- data [1034]
Oct 02 18:46:30.80: [ 2127]: <-- data [1031]
Oct 02 18:46:30.80: [ 2127]: <-- data [1028]
Oct 02 18:46:30.80: [ 2127]: <-- data [1027]
Oct 02 18:46:32.79: [ 2127]: <-- data [1024]
Oct 02 18:46:32.79: [ 2127]: <-- data [1021]
Oct 02 18:46:32.79: [ 2127]: SENT 18429 bytes of data
Oct 02 18:46:32.79: [ 2127]: SEND 1D RTC
Oct 02 18:46:32.79: [ 2127]: <-- data [29]
Oct 02 18:46:32.79: [ 2127]: <-- data [2]
Oct 02 18:46:32.80: [ 2127]: SEND end page
Oct 02 18:46:38.69: [ 2127]: --> [2:]
Oct 02 18:46:38.69: [ 2127]: --> [5:ERROR]
Oct 02 18:46:38.69: [ 2127]: SEND: Unspecified Transmit Phase C error;
Giving up after 3 attempts to send same page "docq/doc1.ps;31", dirnum 0
Oct 02 18:46:38.69: [ 2127]: <-- [9:AT+FTH=3\r]
Oct 02 18:46:38.74: [ 2127]: --> [7:CONNECT]
Oct 02 18:46:38.74: [ 2127]: <-- data [3]
Oct 02 18:46:38.74: [ 2127]: <-- data [2]
Oct 02 18:46:39.48: [ 2127]: --> [2:OK]
Oct 02 18:46:39.48: [ 2127]: <-- [5:ATH0\r]
Oct 02 18:46:39.65: [ 2127]: --> [2:OK]
Oct 02 18:46:39.65: [ 2127]: SESSION END
And conf.ttyS0
# $Id: cirrus2,v 1.2 2000/09/04 18:53:45 lhoward Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names
of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
CountryCode: 1
AreaCode: 702
FAXNumber: +1.702.837.8027
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "Somers Fax"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
#
#
ModemAnswerCmd: ATA # string, command for answering phone
ModemAnswerDataBeginCmd: "" # string, command for start of answered data
call
ModemAnswerDataCmd: ATA # string, command for answering data call
ModemAnswerFaxBeginCmd: "" # string, command for start of answered fax call
ModemAnswerFaxCmd: ATA # string, command for answering fax call
ModemAnswerResponseTimeout: 180000 # integer, answer command timeout (ms)
ModemAnswerVoiceBeginCmd: "" # string, command for start of answered voice
call
ModemAnswerVoiceCmd: ATA # string, command for answering voice call
ModemATCmdDelay: 0 # integer, delay before sending modem an AT cmd (ms)
ModemBaudRateDelay: 0 # integer, delay (ms) after setting baud rate
ModemClassQueryCmd: AT+FCLASS=? # string, command for querying modem
services
ModemCommaPauseTimeCmd: ATS8=2 # string, command for setting time to pause
for comma in dialing string
ModemDialCmd: ATDT%s # string, command for dialing (%s for number to dial)
ModemDialResponseTimeout: 180000 # integer, dialing command timeout (ms)
ModemEchoOffCmd: ATE0 # string, command for disabling command echo
ModemFlowControl: None # string, DTE-DCE flow control scheme
ModemFrameFillOrder: LSB2MSB # string, bit order for HDLC frames
ModemHardFlowCmd: "" # string, command for setting hardware flow control
between DTE and DCE
ModemMinSpeed: 2400 # string, minimum acceptable transmit speed
ModemMfrQueryCmd: AT+FMFR? # string, command for querying modem
manufacturer
ModemModelQueryCmd: AT+FMDL? # string, command for querying modem model
ModemNoAutoAnswerCmd: ATS0=0 # string, command for disabling auto-answer
ModemNoFlowCmd: "" # string, command for disabling hardware flow control
between DTE and DCE
ModemOnHookCmd: ATH0 # string, command for placing phone ``on hook''
ModemPageDoneTimeout: 180000 # integer, page send/receive timeout (ms)
ModemPageStartTimeout: 180000 # integer, page send/receive timeout (ms)
ModemRate: 19200 # integer, baud rate to use for DCE-DTE communication
ModemRecvFillOrder: LSB2MSB # string, bit order for received facsimile data
ModemResetCmds: "" # string, additional commands when resetting modem
ModemResetDelay: 2600 # integer, delay (ms) after sending modem reset
commands
ModemResultCodesCmd: ATQ0 # string, command for enabling result codes
ModemRevQueryCmd: AT+FREV? # string, command for querying modem firmware
revision
ModemSendBeginCmd: "" # string, command to send on establishing carrier
ModemSendFillOrder: LSB2MSB # string, bit order for sending facsimile data
ModemSetVolumeCmd: "ATM0 ATL0M1 ATL8C1 ATL2M1 ATL3M1" # string, commands
for setting modem speaker volume level
ModemSetupAACmd: "" # string, command for setting up adaptive answer
ModemSetupDCDCmd: "" # string, command for setting up DCD handling
ModemSetupDTRCmd: "" # string, command for setting up DTR handling
ModemSoftFlowCmd: "" # string, command for setting software flow control
between DTE and DCE
ModemSoftResetCmd: ATZ # string, command for doing a soft reset
ModemType: Class1 # string, modem type
ModemVerboseResultsCmd: ATV1 # string, command for enabling verbose result
codes
ModemWaitForConnect: No # boolean, force server to wait for ``CONNECT''
response on answer
ModemWaitTimeCmd: ATS7=60 # string, command for setting time to wait for
carrier when dialing
Class1Cmd: AT+FCLASS=1 # string, command to enter class 1
Class1HFLOCmd: "" # string, command to set hardware flow control
Class1FrameOverhead: 4 # integer, extra bytes in a received HDLC frame
Class1NFLOCmd: "" # string, command to set no flow control
Class1RecvAbortOK: 100 # integer, max wait (ms) for ``OK'' after recv abort
Class1RecvIdentTimer: 35000 # integer, max wait (ms) for initial ident
frame
Class1SFLOCmd: "" # string, command to set software flow control
Class1TCFMaxNonZero: 10 # integer, max% of non-zero data in good TCF
Class1TCFMinRun: 1000 # integer, minimum zero run in good TCF
Class1TCFRecvTimeout: 4500 # integer, max wait (ms) for TCF
Class1TCFResponseDelay: 75 # integer, delay between TCF and ack/nak
Class1SendPPMDelay: 75 # integer, delay before sending post-page message
Class1SendTCFDelay: 75 # integer, delay between sending DCS and TCF
Class1SwitchingCmd: "<delay:7>"
Class1TrainingRecovery: 1500 # integer, delay after failed training
I was able to solve an EOP error setting Class1SwitchingCmd (thanks to Lee
Howard). However I'm drawing a blank on this one. Thanks in advance for any
suggestions.
Jerry Stephens
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
