|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] Hylafax and brother faxmachines
High Rich,
You said " I get a "poor line condition" error page printout but the
fax gets through" but following log tells IT DID NOT GET THROUGH. As
long as you get "TRAINING failed" error you can do nothing about it at
the software side. I do not know about the modem you used very much but
i did not have any problems with Multitech MT56344ZPX-PCI and
ISI5634PCI/8 modems.
Sedat
-----Original Message-----
From: Richard Houston [mailto:rhouston@rlhc.net]
Sent: Monday, September 23, 2002 7:51 PM
To: Sedat Yilmazer
Subject: RE: [hylafax-users] Hylafax and brother faxmachines
Guess that would make sense. I have add the latest below.
Thanks for the help.
Rich
Sep 23 12:08:43.43: [ 1360]: SESSION BEGIN 00000198 19995551212
Sep 23 12:08:43.43: [ 1360]: HylaFAX (tm) Version 4.1.2
Sep 23 12:08:43.43: [ 1360]: <-- [4:ATA\r]
Sep 23 12:08:49.63: [ 1360]: --> [7:CONNECT]
Sep 23 12:08:49.63: [ 1360]: ANSWER: FAX CONNECTION DEVICE
'/dev/ttyrp06'
Sep 23 12:08:49.63: [ 1360]: RECV FAX: begin
Sep 23 12:08:49.63: [ 1360]: <-- data [23]
Sep 23 12:08:49.63: [ 1360]: <-- data [2]
Sep 23 12:08:51.32: [ 1360]: --> [7:CONNECT]
Sep 23 12:08:51.32: [ 1360]: <-- data [10]
Sep 23 12:08:51.32: [ 1360]: <-- data [2]
Sep 23 12:08:51.96: [ 1360]: --> [2:OK]
Sep 23 12:08:51.96: [ 1360]: <-- [9:AT+FRH=3\r]
Sep 23 12:08:52.56: [ 1360]: --> [7:CONNECT]
Sep 23 12:08:53.90: [ 1360]: --> [2:OK]
Sep 23 12:08:53.90: [ 1360]: REMOTE TSI "2042841533"
Sep 23 12:08:53.90: [ 1360]: <-- [9:AT+FRH=3\r]
Sep 23 12:08:54.32: [ 1360]: --> [7:CONNECT]
Sep 23 12:08:54.32: [ 1360]: --> [2:OK]
Sep 23 12:08:54.32: [ 1360]: REMOTE wants 9600 bit/s
Sep 23 12:08:54.32: [ 1360]: REMOTE wants page width 1728 pixels in 215
mm
Sep 23 12:08:54.32: [ 1360]: REMOTE wants unlimited page length
Sep 23 12:08:54.32: [ 1360]: REMOTE wants 3.85 line/mm
Sep 23 12:08:54.32: [ 1360]: REMOTE wants 1-D MR
Sep 23 12:08:54.32: [ 1360]: RECV training at v.29 9600 bit/s
Sep 23 12:08:54.32: [ 1360]: <-- [10:AT+FRM=96\r]
Sep 23 12:08:58.81: [ 1360]: --> [0:]
Sep 23 12:08:58.81: [ 1360]: MODEM <Empty line>
Sep 23 12:08:58.81: [ 1360]: <-- data [1]
Sep 23 12:08:59.00: [ 1360]: --> [2:OK]
Sep 23 12:08:59.00: [ 1360]: DELAY 75 ms
Sep 23 12:08:59.07: [ 1360]: <-- [9:AT+FTH=3\r]
Sep 23 12:08:59.30: [ 1360]: --> [7:CONNECT]
Sep 23 12:08:59.30: [ 1360]: <-- data [3]
Sep 23 12:08:59.30: [ 1360]: <-- data [2]
Sep 23 12:09:00.62: [ 1360]: --> [2:OK]
Sep 23 12:09:00.62: [ 1360]: TRAINING failed
Sep 23 12:09:00.62: [ 1360]: <-- [9:AT+FRH=3\r]
Sep 23 12:09:06.62: [ 1360]: --> [7:CONNECT]
Sep 23 12:09:08.10: [ 1360]: --> [2:OK]
Sep 23 12:09:08.10: [ 1360]: REMOTE TSI "2042841533"
Sep 23 12:09:08.10: [ 1360]: <-- [9:AT+FRH=3\r]
Sep 23 12:09:08.44: [ 1360]: --> [7:CONNECT]
Sep 23 12:09:08.44: [ 1360]: --> [2:OK]
Sep 23 12:09:08.44: [ 1360]: REMOTE wants 9600 bit/s
Sep 23 12:09:08.44: [ 1360]: REMOTE wants page width 1728 pixels in 215
mm
Sep 23 12:09:08.44: [ 1360]: REMOTE wants unlimited page length
Sep 23 12:09:08.44: [ 1360]: REMOTE wants 3.85 line/mm
Sep 23 12:09:08.44: [ 1360]: REMOTE wants 1-D MR
Sep 23 12:09:08.44: [ 1360]: RECV training at v.29 9600 bit/s
Sep 23 12:09:08.44: [ 1360]: <-- [10:AT+FRM=96\r]
Sep 23 12:09:12.93: [ 1360]: --> [0:]
Sep 23 12:09:12.93: [ 1360]: MODEM <Empty line>
Sep 23 12:09:12.93: [ 1360]: <-- data [1]
Sep 23 12:09:13.12: [ 1360]: --> [2:OK]
Sep 23 12:09:13.12: [ 1360]: DELAY 75 ms
Sep 23 12:09:13.19: [ 1360]: <-- [9:AT+FTH=3\r]
Sep 23 12:09:13.42: [ 1360]: --> [7:CONNECT]
Sep 23 12:09:13.42: [ 1360]: <-- data [3]
Sep 23 12:09:13.42: [ 1360]: <-- data [2]
Sep 23 12:09:14.74: [ 1360]: --> [2:OK]
Sep 23 12:09:14.74: [ 1360]: TRAINING failed
Sep 23 12:09:14.74: [ 1360]: <-- [9:AT+FRH=3\r]
Sep 23 12:09:21.73: [ 1360]: --> [0:]
Sep 23 12:09:21.73: [ 1360]: MODEM <Empty line>
Sep 23 12:09:21.73: [ 1360]: <-- data [1]
Sep 23 12:09:21.93: [ 1360]: MODEM <Timeout>
Sep 23 12:09:21.93: [ 1360]: DELAY 1500 ms
Sep 23 12:09:23.43: [ 1360]: <-- [9:AT+FTH=3\r]
Sep 23 12:09:23.43: [ 1360]: --> [2:OK]
Sep 23 12:09:23.43: [ 1360]: DELAY 1500 ms
Sep 23 12:09:24.93: [ 1360]: <-- [9:AT+FTH=3\r]
Sep 23 12:09:24.93: [ 1360]: --> [7:CONNECT]
Sep 23 12:09:24.93: [ 1360]: <-- data [23]
Sep 23 12:09:24.93: [ 1360]: <-- data [2]
Sep 23 12:09:26.20: [ 1360]: --> [2:OK]
Sep 23 12:09:27.93: [ 1360]: --> [0:]
Sep 23 12:09:27.93: [ 1360]: MODEM <Empty line>
Sep 23 12:09:27.93: [ 1360]: RECV FAX: Failure to train modems
Sep 23 12:09:27.93: [ 1360]: RECV FAX: end
Sep 23 12:09:27.93: [ 1360]: SESSION END
On Mon, 2002-09-23 at 11:19, Sedat Yilmazer wrote:
>
> A detailed session log would help
>
> Sedat
>
> -----Original Message-----
> From: hylafax-users-bounce@hylafax.org
> [mailto:hylafax-users-bounce@hylafax.org] On Behalf Of Richard Houston
> Sent: Monday, September 23, 2002 6:42 PM
> To: Hylafax-mailing list
> Subject: [hylafax-users] Hylafax and brother faxmachines
>
> Hello all,
>
> I have a high volume hylafax system with 36 lines and receive up to
7000
> faxes a day.
>
> We have a issue with, so far Brother 560 and Brother 1270 model fax
> machines. I have a 560 for testing and when sending a fax I get a
"poor
> line condition" error page printout but the fax gets through.
>
> We are running hylafax 4.1.2 with brand new Multitek MT5600ZDX modems.
>
> Anyone have any ideas on what our issue might be and how to correct
it?
>
> Any help would be greatly appreciated.
>
> Thanks
>
> Richard Houston
>
>
>
>
> ____________________ HylaFAX(tm) Users Mailing List
> _______________________
> To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org <
> /dev/null
> *To learn about commercial HylaFAX(tm) support, mail
> sales@hylafax.org.*
>
>
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
