|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] Unspecified Transmit Phase D error,including +FPHCTO timeout between data and +FET
Phase D errors are end of job response errors usually Number 50 is unspecified, because (usually) the remote machine doesn't respond with the nature of the error. In this case I think it received the job and then hung up before acknowledging it. You could try changing the modem class in the config and seeing if the same machine responds differently as a test.
Here's a list of type 50 errors:
50-69 Transmit Phase D Hangup Codes
50 Unspecified Phase D transmit error
51 RSPREC error
52 No response to MPS repeated 3 times
53 Invalid response to MPS
54 No response to EOP repeated 3 times
55 Invalid response to EOM
56 No response to EOM repeated 3 times
57 Invalid response to EOM
58 Unable to continue after PIN or PIP
>>> "WEGER Michael" <weger.mike@fastrun.at> 09/18/02 07:58AM >>>
Following error occurs, when I try to send a fax to some numbers. IÆve
found some people with the same problem in your mailing-list, but that
didnÆt helped me to solve my problem
IÆm using version 4.1beta2-143. Is this problem solved in a later
version?
Here are the logs:
Your facsimile job to 04717479 was not sent because:
Unspecified Transmit Phase D error, including +FPHCTO timeout
between data and +FET command
The job will be retried at 18:09.
---- Transcript of session follows ----
Sep 17 18:00:30.07: [20991]: SESSION BEGIN 00000833 434717479
Sep 17 18:00:30.07: [20991]: SEND FAX: JOB 278 DEST 04717479 COMMID
00000833
Sep 17 18:00:30.07: [20991]: MODEM set DTR OFF
Sep 17 18:00:30.07: [20991]: DELAY 2600 ms
Sep 17 18:00:32.67: [20991]: MODEM set DTR ON
Sep 17 18:00:32.67: [20991]: MODEM set baud rate: 19200 baud, input flow
NONE, output flow NONE
Sep 17 18:00:32.67: [20991]: MODEM flush i/o
Sep 17 18:00:32.67: [20991]: <-- [15:ATE0V1Q0S0=0H0\r]
Sep 17 18:00:32.82: [20991]: --> [2:OK]
Sep 17 18:00:32.82: [20991]: <-- [12:ATS8=2S7=60\r]
Sep 17 18:00:32.96: [20991]: --> [2:OK]
Sep 17 18:00:32.96: [20991]: <-- [14:AT+FCLASS=2.0\r]
Sep 17 18:00:33.10: [20991]: --> [2:OK]
Sep 17 18:00:33.10: [20991]: <-- [9:AT+FLO=0\r]
Sep 17 18:00:33.24: [20991]: --> [2:OK]
Sep 17 18:00:33.24: [20991]: <-- [9:AT+FPP=0\r]
Sep 17 18:00:33.38: [20991]: --> [2:OK]
Sep 17 18:00:33.38: [20991]: <-- [9:AT+FBO=0\r]
Sep 17 18:00:33.52: [20991]: --> [2:OK]
Sep 17 18:00:33.52: [20991]: <-- [10:AT+FCT=30\r]
Sep 17 18:00:33.66: [20991]: --> [2:OK]
Sep 17 18:00:33.66: [20991]: <-- [15:AT+FNR=1,1,1,1\r]
Sep 17 18:00:33.81: [20991]: --> [2:OK]
Sep 17 18:00:33.81: [20991]: <-- [9:AT+FIE=0\r]
Sep 17 18:00:33.95: [20991]: --> [2:OK]
Sep 17 18:00:33.95: [20991]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Sep 17 18:00:34.10: [20991]: --> [2:OK]
Sep 17 18:00:34.10: [20991]: <-- [5:ATM0\r]
Sep 17 18:00:34.24: [20991]: --> [2:OK]
Sep 17 18:00:34.24: [20991]: MODEM input buffering enabled
Sep 17 18:00:34.24: [20991]: <-- [14:AT+FCLASS=2.0\r]
Sep 17 18:00:34.48: [20991]: --> [2:OK]
Sep 17 18:00:34.48: [20991]: <-- [9:AT+FLO=0\r]
Sep 17 18:00:34.72: [20991]: --> [2:OK]
Sep 17 18:00:34.72: [20991]: <-- [9:AT+FPP=0\r]
Sep 17 18:00:34.96: [20991]: --> [2:OK]
Sep 17 18:00:34.96: [20991]: <-- [9:AT+FBO=0\r]
Sep 17 18:00:35.20: [20991]: --> [2:OK]
Sep 17 18:00:35.20: [20991]: <-- [10:AT+FCT=30\r]
Sep 17 18:00:35.44: [20991]: --> [2:OK]
Sep 17 18:00:35.44: [20991]: <-- [15:AT+FNR=1,1,1,1\r]
Sep 17 18:00:35.68: [20991]: --> [2:OK]
Sep 17 18:00:35.68: [20991]: <-- [9:AT+FIE=0\r]
Sep 17 18:00:35.92: [20991]: --> [2:OK]
Sep 17 18:00:35.92: [20991]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Sep 17 18:00:36.17: [20991]: --> [2:OK]
Sep 17 18:00:36.17: [20991]: <-- [27:AT+FLI="xxxxxxxxxxxxx"\r]
Sep 17 18:00:36.42: [20991]: --> [2:OK]
Sep 17 18:00:36.42: [20991]: DIAL 04717479
Sep 17 18:00:36.42: [20991]: <-- [13:ATDT04717479\r]
Sep 17 18:00:51.71: [20991]: --> [4:+FCO]
Sep 17 18:00:55.00: [20991]: -->
[37:+FNF:_ÇÇI_GOTTH-U-EBENBERG[ÇÇ+______]
Sep 17 18:00:55.00: [20991]: REMOTE NSF "_ÇÇI_GOTTH-U-EBENBERG[ÇÇ+
______"
Sep 17 18:00:55.00: [20991]: --> [27:+FCI:" +434717+479"]
Sep 17 18:00:55.00: [20991]: REMOTE CSI "+434717+479"
Sep 17 18:00:55.00: [20991]: --> [20:+FIS:1,3,0,2,1,0,0,5]
Sep 17 18:00:55.00: [20991]: --> [2:OK]
Sep 17 18:00:55.00: [20991]: REMOTE best rate 9600 bit/s
Sep 17 18:00:55.00: [20991]: REMOTE max page width 1728 pixels in 215 mm
Sep 17 18:00:55.00: [20991]: REMOTE max unlimited page length
Sep 17 18:00:55.00: [20991]: REMOTE best vres 7.7 line/mm
Sep 17 18:00:55.00: [20991]: REMOTE best format 2-D MR
Sep 17 18:00:55.00: [20991]: REMOTE best 20 ms/scanline
Sep 17 18:00:55.00: [20991]: USE 9600 bit/s
Sep 17 18:00:55.00: [20991]: USE 20 ms/scanline
Sep 17 18:00:55.00: [20991]: SEND file "docq/doc280.ps;01"
Sep 17 18:00:55.00: [20991]: USE page width 1728 pixels in 215 mm
Sep 17 18:00:55.00: [20991]: USE unlimited page length
Sep 17 18:00:55.00: [20991]: USE 7.7 line/mm
Sep 17 18:00:55.00: [20991]: USE 1-D MR
Sep 17 18:00:55.00: [20991]: <-- [23:AT+FIS=1,3,0,2,0,0,0,5\r]
Sep 17 18:00:55.25: [20991]: --> [2:OK]
Sep 17 18:00:55.25: [20991]: <-- [7:AT+FDT\r]
Sep 17 18:00:55.53: [20991]: --> [20:+FCS:1,3,0,2,0,0,0,5]
Sep 17 18:01:01.00: [20991]: --> [7:CONNECT]
Sep 17 18:01:01.00: [20991]: SEND begin page
Sep 17 18:01:10.98: [20991]: SENT 20631 bytes of data
Sep 17 18:01:10.98: [20991]: SEND 1D RTC
Sep 17 18:01:10.98: [20991]: SEND end page
Sep 17 18:01:10.98: [20991]: SEND send EOP (no more pages or documents)
Sep 17 18:04:10.98: [20991]: MODEM TIMEOUT: reading line from modem
Sep 17 18:04:10.98: [20991]: REMOTE HANGUP: Unspecified Transmit Phase D
error, including +FPHCTO timeout between data and +FET command (code 50)
Sep 17 18:04:10.98: [20991]: <-- [7:AT+FKS\r]
Sep 17 18:04:40.98: [20991]: MODEM TIMEOUT: reading line from modem
Sep 17 18:04:40.98: [20991]: MODEM <Timeout>
Sep 17 18:04:40.98: [20991]: <-- [5:ATH0\r]
Sep 17 18:04:45.98: [20991]: MODEM TIMEOUT: reading line from modem
Sep 17 18:04:45.98: [20991]: MODEM <Timeout>
Sep 17 18:04:45.98: [20991]: MODEM set DTR OFF
Sep 17 18:04:45.98: [20991]: SESSION END
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
