[hylafax-users] NO CARRIER does not seem to signal a SEND FAILED

[Dirk Lutzebaeck <lutzeb@aeccom.com>]

Hi,

this is hylafax 4.1beta3 on Redhat 7.1 using an Eicon ISDN card.

The system sends a fax and the carrier drops after connect. Problem is
that hylafax thinks the fax is sent but to my understanding it should
issue a SEND FAILED:

Here is the log:
Sep 05 10:09:41.74: [  682]: SESSION BEGIN 00021498 4162XXXXXXXXXX
Sep 05 10:09:41.74: [  682]: SEND FAX: JOB 14869 DEST 004162XXXXXXXXXX COMMID 00021
498
Sep 05 10:09:41.74: [  682]: DELAY 2600 ms
Sep 05 10:09:44.33: [  682]: <-- [4:ATZ\r]
Sep 05 10:09:44.34: [  682]: --> [2:OK]
Sep 05 10:09:44.34: [  682]: <-- [32:AT&E7261557S23=2&L*E0V1Q0S0=0H0\r]
Sep 05 10:09:44.35: [  682]: --> [31:AT&E7261557S23=2&L*E0V1Q0S0=0H0]
Sep 05 10:09:44.35: [  682]: --> [2:OK]
Sep 05 10:09:44.35: [  682]: <-- [12:ATS8=2S7=60\r]
Sep 05 10:09:44.36: [  682]: --> [2:OK]
Sep 05 10:09:44.36: [  682]: <-- [12:AT+FCLASS=2\r]
Sep 05 10:09:44.37: [  682]: --> [2:OK]
Sep 05 10:09:44.37: [  682]: <-- [10:AT+FTBC=0\r]
Sep 05 10:09:44.38: [  682]: --> [2:OK]
Sep 05 10:09:44.38: [  682]: <-- [10:AT+FBOR=0\r]
Sep 05 10:09:44.39: [  682]: --> [2:OK]
Sep 05 10:09:44.39: [  682]: <-- [13:AT+FPHCTO=30\r]
Sep 05 10:09:44.40: [  682]: --> [2:OK]
Sep 05 10:09:44.40: [  682]: <-- [24:AT+FDCC=1,5,2,2,3,0,0,0\r]
Sep 05 10:09:44.41: [  682]: --> [2:OK]
Sep 05 10:09:44.41: [  682]: <-- [5:ATM0\r]
Sep 05 10:09:44.42: [  682]: --> [2:OK]
Sep 05 10:09:44.42: [  682]: <-- [12:AT+FCLASS=2\r]
Sep 05 10:09:44.53: [  682]: --> [2:OK]
Sep 05 10:09:44.53: [  682]: <-- [10:AT+FTBC=0\r]
Sep 05 10:09:44.64: [  682]: --> [2:OK]
Sep 05 10:09:44.64: [  682]: <-- [10:AT+FBOR=0\r]
Sep 05 10:09:44.75: [  682]: --> [2:OK]
Sep 05 10:09:44.75: [  682]: <-- [13:AT+FPHCTO=30\r]
Sep 05 10:09:44.86: [  682]: --> [2:OK]
Sep 05 10:09:44.86: [  682]: <-- [24:AT+FDCC=1,5,2,2,3,0,0,0\r]
Sep 05 10:09:44.97: [  682]: --> [2:OK]
Sep 05 10:09:44.97: [  682]: <-- [25:AT+FLID="via aeccom.com"\r]
Sep 05 10:09:45.08: [  682]: --> [2:OK]
Sep 05 10:09:45.09: [  682]: DIAL 004162XXXXXXXX
Sep 05 10:09:45.09: [  682]: <-- [18:ATDT004162XXXXXX\r]
Sep 05 10:10:02.16: [  682]: --> [5:+FCON]
Sep 05 10:10:02.16: [  682]: --> [28:+FCSI:"       062 832 04 06"]
Sep 05 10:10:02.16: [  682]: REMOTE CSI "062 832 04 06"
Sep 05 10:10:02.16: [  682]: --> [21:+FDIS:1,5,0,2,3,1,0,0]
Sep 05 10:10:02.16: [  682]: --> [21:+FDIS:1,5,0,2,0,1,0,0]
Sep 05 10:10:02.16: [  682]: --> [2:OK]
Sep 05 10:10:02.16: [  682]: REMOTE best rate 14400 bit/s
Sep 05 10:10:02.16: [  682]: REMOTE max page width 1728 pixels in 215 mm
Sep 05 10:10:02.16: [  682]: REMOTE max unlimited page length
Sep 05 10:10:02.16: [  682]: REMOTE best vres 7.7 line/mm
Sep 05 10:10:02.16: [  682]: REMOTE best format 1-D MR
Sep 05 10:10:02.16: [  682]: REMOTE supports T.30 Annex A, ECM
Sep 05 10:10:02.16: [  682]: REMOTE best 0 ms/scanline
Sep 05 10:10:02.16: [  682]: USE 14400 bit/s
Sep 05 10:10:02.16: [  682]: USE 0 ms/scanline
Sep 05 10:10:02.16: [  682]: USE error correction mode
Sep 05 10:10:02.16: [  682]: <-- [5:ATH0\r]
Sep 05 10:10:02.27: [  682]: --> [10:NO CARRIER]
Sep 05 10:10:02.27: [  682]: MODEM No carrier
Sep 05 10:10:02.27: [  682]: SESSION END



After that I got a completion mail:

Your facsimile job to 004162XXXXXXXXX was completed successfully.

         Pages: 0
       Quality: Fine
    Page Width: 209 (mm)
   Page Length: 296 (mm)
   Signal Rate: 14400 bit/s
   Data Format: 2-D MMR
Submitted From: toro.aeccom.int
         JobID: 14869
       GroupID: 14869
        CommID: c00021498

Processing time was 0:26.


Any suggestions?

Dirk

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*