|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Problems recieving fax, New user, New installation
My setup -
Hardware is AMD 1800xp, 512 meg ram, 80gig drive
fax modem - Digi Datafire RAS PTE 24 - This is a 24 port faxmodem card
that accepts a t1
OS - Red Hat Linux 2.4.7-10
Hylafax version - hylafax-4.1.3-1rh7.i386.rpm
my modem config :
CountryCode: 1
AreaCode: 610
FAXNumber: XXXXXXXXXXXX
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: XXXXX
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
#
ModemType: Class1 # use this to supply a hint
ModemRate: 19200 # rate for DCE-DTE communication
ModemFlowControl: rtscts # default
#
ModemNoFlowCmd: AT&K0 # setup no flow control
ModemHardFlowCmd: AT&K3 # setup hardware flow control
ModemSoftFlowCmd: AT&K4 # setup software flow control
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
#
ModemMfrQueryCmd: !Rockwell
ModemModelQueryCmd: !RC288DPi
ModemRevQueryCmd: ATI3 # product information
#
The problem -
I can send a fax from my PC to the hylafax server using sendfax, hylafax
recieves it without error.
When I send a fax from a regular fax machine, the fax fails complaining
about recieving an EOL after 5 seconds. This happens when my modems are
configured for class 1 or 2
If I configure them for class 2.0 or 2.1, everything looks successful,
but the tiff file is corrupt.
HELP!
From messages file :
Sep 3 12:02:14 localhost FaxGetty[5540]: ANSWER: FAX CONNECTION DEVICE
'/dev/ttyG0_03'
Sep 3 12:03:05 localhost FaxGetty[5540]: MODEM ROCKWELL
RC288DPi/V80006691_K4-K56_DS
A session log file :
Sep 03 12:02:08.74: [ 5540]: SESSION BEGIN 00000054 18885123498
Sep 03 12:02:08.74: [ 5540]: HylaFAX (tm) Version 4.1.3
Sep 03 12:02:08.74: [ 5540]: <-- [4:ATA\r]
Sep 03 12:02:14.74: [ 5540]: --> [7:CONNECT]
Sep 03 12:02:14.74: [ 5540]: ANSWER: FAX CONNECTION DEVICE
'/dev/ttyG0_03'
Sep 03 12:02:14.74: [ 5540]: RECV FAX: begin
Sep 03 12:02:14.74: [ 5540]: <-- data [23]
Sep 03 12:02:14.74: [ 5540]: <-- data [2]
Sep 03 12:02:15.77: [ 5540]: --> [1:]
Sep 03 12:02:15.77: [ 5540]: --> [7:CONNECT]
Sep 03 12:02:15.77: [ 5540]: <-- data [10]
Sep 03 12:02:15.77: [ 5540]: <-- data [2]
Sep 03 12:02:16.74: [ 5540]: --> [1:]
Sep 03 12:02:16.74: [ 5540]: --> [2:OK]
Sep 03 12:02:16.74: [ 5540]: <-- [9:AT+FRH=3\r]
Sep 03 12:02:17.08: [ 5540]: --> [7:CONNECT]
Sep 03 12:02:18.71: [ 5540]: --> [2:OK]
Sep 03 12:02:18.71: [ 5540]: REMOTE TSI ""
Sep 03 12:02:18.71: [ 5540]: <-- [9:AT+FRH=3\r]
Sep 03 12:02:18.89: [ 5540]: --> [7:CONNECT]
Sep 03 12:02:19.15: [ 5540]: --> [2:OK]
Sep 03 12:02:19.15: [ 5540]: REMOTE wants 9600 bit/s
Sep 03 12:02:19.15: [ 5540]: REMOTE wants page width 1728 pixels in 215
mm
Sep 03 12:02:19.15: [ 5540]: REMOTE wants unlimited page length
Sep 03 12:02:19.15: [ 5540]: REMOTE wants 3.85 line/mm
Sep 03 12:02:19.15: [ 5540]: REMOTE wants 2-D MR
Sep 03 12:02:19.15: [ 5540]: RECV training at v.29 9600 bit/s
Sep 03 12:02:19.15: [ 5540]: <-- [10:AT+FRM=96\r]
Sep 03 12:02:23.65: [ 5540]: --> [0:]
Sep 03 12:02:23.65: [ 5540]: MODEM <Empty line>
Sep 03 12:02:23.65: [ 5540]: <-- data [1]
Sep 03 12:02:23.68: [ 5540]: --> [2:OK]
Sep 03 12:02:23.68: [ 5540]: DELAY 75 ms
Sep 03 12:02:23.76: [ 5540]: <-- [9:AT+FTH=3\r]
Sep 03 12:02:24.93: [ 5540]: --> [7:CONNECT]
Sep 03 12:02:24.93: [ 5540]: <-- data [3]
Sep 03 12:02:24.93: [ 5540]: <-- data [2]
Sep 03 12:02:25.72: [ 5540]: --> [2:OK]
Sep 03 12:02:25.72: [ 5540]: TRAINING failed
Sep 03 12:02:25.72: [ 5540]: <-- [9:AT+FRH=3\r]
Sep 03 12:02:26.06: [ 5540]: --> [7:CONNECT]
Sep 03 12:02:27.69: [ 5540]: --> [2:OK]Sep 03 12:02:27.69: [ 5540]: <--
[9:AT+FRH=3\r]
Sep 03 12:02:27.87: [ 5540]: --> [7:CONNECT]
Sep 03 12:02:28.14: [ 5540]: --> [2:OK]
Sep 03 12:02:28.14: [ 5540]: REMOTE wants 7200 bit/s
Sep 03 12:02:28.14: [ 5540]: REMOTE wants page width 1728 pixels in 215
mm
Sep 03 12:02:28.14: [ 5540]: REMOTE wants unlimited page length
Sep 03 12:02:28.14: [ 5540]: REMOTE wants 3.85 line/mm
Sep 03 12:02:28.14: [ 5540]: REMOTE wants 2-D MR
Sep 03 12:02:28.14: [ 5540]: RECV training at v.29 7200 bit/s
Sep 03 12:02:28.14: [ 5540]: <-- [10:AT+FRM=72\r]
Sep 03 12:02:32.64: [ 5540]: --> [0:]
Sep 03 12:02:32.64: [ 5540]: MODEM <Empty line>
Sep 03 12:02:32.64: [ 5540]: <-- data [1]
Sep 03 12:02:32.67: [ 5540]: --> [2:OK]
Sep 03 12:02:32.67: [ 5540]: DELAY 75 ms
Sep 03 12:02:32.75: [ 5540]: <-- [9:AT+FTH=3\r]
Sep 03 12:02:33.94: [ 5540]: --> [7:CONNECT]
Sep 03 12:02:33.94: [ 5540]: <-- data [3]
Sep 03 12:02:33.94: [ 5540]: <-- data [2]
Sep 03 12:02:34.72: [ 5540]: --> [2:OK]
Sep 03 12:02:34.72: [ 5540]: TRAINING failed
Sep 03 12:02:34.72: [ 5540]: <-- [9:AT+FRH=3\r]
Sep 03 12:02:35.05: [ 5540]: --> [7:CONNECT]
Sep 03 12:02:36.68: [ 5540]: --> [2:OK]
Sep 03 12:02:36.68: [ 5540]: REMOTE TSI ""
Sep 03 12:02:36.68: [ 5540]: <-- [9:AT+FRH=3\r]
Sep 03 12:02:36.86: [ 5540]: --> [7:CONNECT]
Sep 03 12:02:37.12: [ 5540]: --> [2:OK]
Sep 03 12:02:37.12: [ 5540]: REMOTE wants 4800 bit/s
Sep 03 12:02:37.12: [ 5540]: REMOTE wants page width 1728 pixels in 215
mm
Sep 03 12:02:37.12: [ 5540]: REMOTE wants unlimited page length
Sep 03 12:02:37.12: [ 5540]: REMOTE wants 3.85 line/mm
Sep 03 12:02:37.12: [ 5540]: REMOTE wants 2-D MR
Sep 03 12:02:37.12: [ 5540]: RECV training at v.27ter 4800 bit/s
Sep 03 12:02:37.12: [ 5540]: <-- [10:AT+FRM=48\r]
Sep 03 12:02:41.62: [ 5540]: --> [0:]
Sep 03 12:02:41.62: [ 5540]: MODEM <Empty line>
Sep 03 12:02:41.62: [ 5540]: <-- data [1]
Sep 03 12:02:41.65: [ 5540]: --> [2:OK]
Sep 03 12:02:41.65: [ 5540]: DELAY 75 ms
Sep 03 12:02:41.73: [ 5540]: <-- [9:AT+FTH=3\r]
Sep 03 12:02:42.92: [ 5540]: --> [7:CONNECT]
Sep 03 12:02:42.92: [ 5540]: <-- data [3]
Sep 03 12:02:42.92: [ 5540]: <-- data [2]
Sep 03 12:02:43.71: [ 5540]: --> [2:OK]
Sep 03 12:02:43.71: [ 5540]: TRAINING failed
Aug 30 15:25:13.40: [ 4905]: SESSION BEGIN 00000047 18885123498
Aug 30 15:25:13.40: [ 4905]: HylaFAX (tm) Version 4.1.3
Aug 30 15:25:13.40: [ 4905]: <-- [4:ATA\r]
Aug 30 15:25:19.96: [ 4905]: --> [5:+FCON]
Aug 30 15:25:19.96: [ 4905]: ANSWER: FAX CONNECTION DEVICE
'/dev/ttyG0_03'
Aug 30 15:25:19.96: [ 4905]: RECV FAX: begin
Aug 30 15:25:21.94: [ 4905]: --> [29:+FTSI: "6109416750 "]
Aug 30 15:25:21.94: [ 4905]: REMOTE TSI "6109416750"
Aug 30 15:25:21.94: [ 4905]: --> [22:+FDCS: 0,5,0,2,3,2,0,0]
Aug 30 15:25:21.94: [ 4905]: REMOTE wants 14400 bit/s
Aug 30 15:25:21.94: [ 4905]: REMOTE wants page width 1728 pixels in 215
mm
Aug 30 15:25:21.94: [ 4905]: REMOTE wants unlimited page length
Aug 30 15:25:21.94: [ 4905]: REMOTE wants 3.85 line/mm
Aug 30 15:25:21.94: [ 4905]: REMOTE wants 2-D MMR
Aug 30 15:25:21.94: [ 4905]: REMOTE wants T.30 Annex C, half duplex ECM
Aug 30 15:25:21.94: [ 4905]: --> [2:OK]
Aug 30 15:25:21.94: [ 4905]: <-- [7:AT+FDR\r]
Aug 30 15:25:25.52: [ 4905]: --> [5:+FCFR]
Aug 30 15:25:27.81: [ 4905]: --> [22:+FDCS: 0,5,0,2,3,2,0,0]
Aug 30 15:25:27.81: [ 4905]: REMOTE wants 14400 bit/s
Aug 30 15:25:27.81: [ 4905]: REMOTE wants page width 1728 pixels in 215
mm
Aug 30 15:25:27.81: [ 4905]: REMOTE wants unlimited page length
Aug 30 15:25:27.81: [ 4905]: REMOTE wants 3.85 line/mm
Aug 30 15:25:27.81: [ 4905]: REMOTE wants 2-D MMR
Aug 30 15:25:27.81: [ 4905]: REMOTE wants T.30 Annex C, half duplex ECM
Aug 30 15:25:27.81: [ 4905]: --> [7:CONNECT]
Aug 30 15:25:27.81: [ 4905]: RECV: begin page
Aug 30 15:25:27.83: [ 4905]: RECV: send trigger 021
Aug 30 15:25:27.83: [ 4905]: <-- data [1]
Aug 30 15:26:27.83: [ 4905]: <-- data [1]
Aug 30 15:26:27.83: [ 4905]: RECV: Missing EOL after 5 seconds
Aug 30 15:26:27.87: [ 4905]: REMOTE HANGUP: Missing EOL after 5 seconds
(section 3.2/T.4) (code 91)
Aug 30 15:26:27.87: [ 4905]: RECV FAX (00000047): recvq/fax00047.tif
from 6109416750, route to <unspecified>, 0 pages in 1:08
Aug 30 15:26:27.87: [ 4905]: RECV FAX: Missing EOL after 5 seconds
(section 3.2/T.4)
Aug 30 15:26:27.87: [ 4905]: <-- [6:AT+FK\r]
Aug 30 15:26:28.23: [ 4905]: --> [2:]
Aug 30 15:26:28.23: [ 4905]: --> [10:+FHNG: 102]
Aug 30 15:26:28.23: [ 4905]: REMOTE HANGUP: COMREC invalid response
received (code 102)
Aug 30 15:26:28.23: [ 4905]: --> [2:OK]
Aug 30 15:26:28.23: [ 4905]: RECV FAX (00000047): session with
6109416750 terminated abnormally: Missing EOL after 5 seconds (section
3.2/T.4)
Aug 30 15:26:28.23: [ 4905]: RECV FAX: bin/faxrcvd "recvq/fax00047.tif"
"ttyG0_03" "00000047" "Missing EOL after 5 seconds (section 3.2/T.4)" ""
""
Aug 30 15:26:28.32: [ 4905]: RECV FAX: end
Aug 30 15:26:28.32: [ 4905]: SESSION END
A different log file :
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
