[hylafax-users] Failure to train remote modem

To: hylafax-users@hylafax.org
Subject: [hylafax-users] Failure to train remote modem
From: Marius <lists@linkx.net>
Date: Sun, 28 Jul 2002 10:00:28 +0200

We use an Eicon ISDN board to handle fax traffic, which I configured for a 
Class 1 tty-connection. Class 2 is possible, but generates many connection 
failures and CAPI (Capi4Hylafax) doesn't report back in xferfaxlog.

It works pretty well for us except for some types of faxmachine that fail 
to connect. This is the resultlog of one of these attemps to a Brother 
Intellifax 770. I hope you can shed some light is this issue.

Jul 26 20:45:03.74: [28713]: SESSION BEGIN 00006807 3120xxxxxxxxxxx
Jul 26 20:45:03.74: [28713]: HylaFAX (tm) Version 4.1.2
Jul 26 20:45:03.74: [28713]: SEND FAX: JOB 5652 DEST xxxxxxxxxx COMMID 
00006807 DEVICE /dev/ttyds01'
Jul 26 20:45:03.74: [28713]: DELAY 75 ms
Jul 26 20:45:03.82: [28713]: DELAY 2600 ms
Jul 26 20:45:06.42: [28713]: <-- [4:ATZ\r]
Jul 26 20:45:06.42: [28713]: --> [3:ATZ]
Jul 26 20:45:06.42: [28713]: --> [2:OK]
Jul 26 20:45:06.42: [28713]: DELAY 3000 ms
Jul 26 20:45:09.42: [28713]: <-- [5:ATE0\r]
Jul 26 20:45:09.42: [28713]: --> [4:ATE0]
Jul 26 20:45:09.42: [28713]: --> [2:OK]
Jul 26 20:45:09.42: [28713]: <-- [5:ATV1\r]
Jul 26 20:45:09.42: [28713]: --> [2:OK]
Jul 26 20:45:09.42: [28713]: <-- [5:ATQ0\r]
Jul 26 20:45:09.42: [28713]: --> [2:OK]
Jul 26 20:45:09.42: [28713]: <-- [7:ATS0=0\r]
Jul 26 20:45:09.42: [28713]: --> [2:OK]
Jul 26 20:45:09.42: [28713]: <-- [7:ATS8=2\r]
Jul 26 20:45:09.42: [28713]: --> [2:OK]
Jul 26 20:45:09.42: [28713]: <-- [8:ATS7=60\r]
Jul 26 20:45:09.42: [28713]: --> [2:OK]
Jul 26 20:45:09.42: [28713]: <-- [12:AT+FCLASS=1\r]
Jul 26 20:45:09.42: [28713]: --> [2:OK]
Jul 26 20:45:09.42: [28713]: <-- [5:ATM0\r]
Jul 26 20:45:09.42: [28713]: --> [2:OK]
Jul 26 20:45:09.42: [28713]: <-- [12:AT+FCLASS=1\r]
Jul 26 20:45:09.52: [28713]: --> [2:OK]
Jul 26 20:45:09.52: [28713]: DIAL 31302400217
Jul 26 20:45:09.52: [28713]: <-- [16:ATDT31302400217\r]
Jul 26 20:45:21.35: [28713]: --> [7:CONNECT]
Jul 26 20:45:22.71: [28713]: --> [2:OK]
Jul 26 20:45:22.71: [28713]: REMOTE NSF "00 00 56 55 55 00 88 90 80 5F 00 15"
Jul 26 20:45:22.71: [28713]: NSF remote fax equipment: Brother Intellifax 770
Jul 26 20:45:22.71: [28713]: <-- [9:AT+FRH=3\r]
Jul 26 20:45:22.71: [28713]: --> [7:CONNECT]
Jul 26 20:45:23.03: [28713]: --> [2:OK]
Jul 26 20:45:23.03: [28713]: REMOTE best rate 9600 bit/s
Jul 26 20:45:23.03: [28713]: REMOTE max page width 1728 pixels in 215 mm
Jul 26 20:45:23.03: [28713]: REMOTE max unlimited page length
Jul 26 20:45:23.03: [28713]: REMOTE best vres 7.7 line/mm
Jul 26 20:45:23.03: [28713]: REMOTE best format 1-D MR
Jul 26 20:45:23.03: [28713]: REMOTE supports T.30 Annex A, ECM
Jul 26 20:45:23.03: [28713]: REMOTE best 20 ms, 10 ms/scanline
Jul 26 20:45:23.03: [28713]: USE 9600 bit/s
Jul 26 20:45:23.03: [28713]: USE 20 ms, 10 ms/scanline
Jul 26 20:45:23.03: [28713]: SEND file "docq/doc5954.ps;00"
Jul 26 20:45:23.03: [28713]: USE page width 1728 pixels in 215 mm
Jul 26 20:45:23.03: [28713]: USE unlimited page length
Jul 26 20:45:23.03: [28713]: USE 3.85 line/mm
Jul 26 20:45:23.03: [28713]: USE 1-D MR
Jul 26 20:45:23.03: [28713]: SEND training at v.29 9600 bit/s
Jul 26 20:45:23.03: [28713]: <-- [9:AT+FTH=3\r]
Jul 26 20:45:23.15: [28713]: --> [7:CONNECT]
Jul 26 20:45:23.88: [28713]: --> [7:CONNECT]
Jul 26 20:45:25.23: [28713]: --> [2:OK]
Jul 26 20:45:25.23: [28713]: <-- [9:AT+FTS=7\r]
Jul 26 20:45:25.23: [28713]: --> [2:OK]
Jul 26 20:45:25.23: [28713]: <-- [10:AT+FTM=96\r]
Jul 26 20:45:25.55: [28713]: --> [7:CONNECT]
Jul 26 20:45:27.11: [28713]: --> [2:OK]
Jul 26 20:45:27.11: [28713]: <-- [9:AT+FRH=3\r]
Jul 26 20:45:27.15: [28713]: --> [7:CONNECT]
Jul 26 20:45:27.68: [28713]: --> [2:OK]
Jul 26 20:45:27.68: [28713]: <-- [9:AT+FRH=3\r]
Jul 26 20:45:27.68: [28713]: --> [7:CONNECT]
Jul 26 20:45:28.00: [28713]: --> [2:OK]
Jul 26 20:45:28.00: [28713]: SEND training at v.29 9600 bit/s
Jul 26 20:45:28.00: [28713]: <-- [9:AT+FTH=3\r]
Jul 26 20:45:28.13: [28713]: --> [7:CONNECT]
Jul 26 20:45:28.86: [28713]: --> [7:CONNECT]
Jul 26 20:45:30.21: [28713]: --> [2:OK]
Jul 26 20:45:30.21: [28713]: <-- [9:AT+FTS=7\r]
Jul 26 20:45:30.21: [28713]: --> [2:OK]
Jul 26 20:45:30.21: [28713]: <-- [10:AT+FTM=96\r]
Jul 26 20:45:30.52: [28713]: --> [7:CONNECT]
Jul 26 20:45:32.08: [28713]: --> [2:OK]
Jul 26 20:45:32.08: [28713]: <-- [9:AT+FRH=3\r]
Jul 26 20:45:32.12: [28713]: --> [7:CONNECT]
Jul 26 20:45:32.68: [28713]: --> [2:OK]
Jul 26 20:45:32.68: [28713]: <-- [9:AT+FRH=3\r]
Jul 26 20:45:32.68: [28713]: --> [7:CONNECT]
Jul 26 20:45:33.01: [28713]: --> [2:OK]
Jul 26 20:45:33.01: [28713]: SEND training at v.29 9600 bit/s
Jul 26 20:45:33.01: [28713]: <-- [9:AT+FTH=3\r]
Jul 26 20:45:33.13: [28713]: --> [7:CONNECT]
Jul 26 20:45:33.86: [28713]: --> [7:CONNECT]
Jul 26 20:45:35.21: [28713]: --> [2:OK]
Jul 26 20:45:35.21: [28713]: <-- [9:AT+FTS=7\r]
Jul 26 20:45:35.21: [28713]: --> [2:OK]
Jul 26 20:45:35.21: [28713]: <-- [10:AT+FTM=96\r]
Jul 26 20:45:35.52: [28713]: --> [7:CONNECT]
Jul 26 20:45:37.08: [28713]: --> [2:OK]
Jul 26 20:45:37.08: [28713]: <-- [9:AT+FRH=3\r]
Jul 26 20:45:37.27: [28713]: --> [7:CONNECT]
Jul 26 20:45:38.45: [28713]: --> [2:OK]
Jul 26 20:45:38.45: [28713]: DELAY 1500 ms
Jul 26 20:45:39.95: [28713]: SEND training at v.29 7200 bit/s
Jul 26 20:45:39.95: [28713]: <-- [9:AT+FTH=3\r]
Jul 26 20:45:39.96: [28713]: --> [7:CONNECT]
Jul 26 20:45:40.70: [28713]: --> [7:CONNECT]
Jul 26 20:45:42.04: [28713]: --> [2:OK]
Jul 26 20:45:42.04: [28713]: <-- [9:AT+FTS=7\r]
Jul 26 20:45:42.04: [28713]: --> [2:OK]
Jul 26 20:45:42.04: [28713]: <-- [10:AT+FTM=72\r]
Jul 26 20:45:42.36: [28713]: --> [7:CONNECT]
Jul 26 20:45:43.92: [28713]: --> [2:OK]
Jul 26 20:45:43.92: [28713]: <-- [9:AT+FRH=3\r]
Jul 26 20:45:44.12: [28713]: --> [7:CONNECT]
Jul 26 20:45:45.29: [28713]: --> [2:OK]
Jul 26 20:45:45.29: [28713]: DELAY 1500 ms
Jul 26 20:45:46.80: [28713]: SEND training at v.27ter 4800 bit/s
Jul 26 20:45:46.80: [28713]: <-- [9:AT+FTH=3\r]
Jul 26 20:45:46.81: [28713]: --> [7:CONNECT]
Jul 26 20:45:47.54: [28713]: --> [7:CONNECT]
Jul 26 20:45:48.89: [28713]: --> [2:OK]
Jul 26 20:45:48.89: [28713]: <-- [9:AT+FTS=7\r]
Jul 26 20:45:48.89: [28713]: --> [2:OK]
Jul 26 20:45:48.89: [28713]: <-- [10:AT+FTM=48\r]
Jul 26 20:45:49.89: [28713]: --> [7:CONNECT]
Jul 26 20:45:51.45: [28713]: --> [2:OK]
Jul 26 20:45:51.45: [28713]: <-- [9:AT+FRH=3\r]
Jul 26 20:45:54.55: [28713]: --> [0:]
Jul 26 20:45:54.55: [28713]: MODEM <Empty line>
Jul 26 20:45:54.55: [28713]: --> [2:]
Jul 26 20:45:54.55: [28713]: --> [2:OK]
Jul 26 20:45:54.55: [28713]: DELAY 1500 ms
Jul 26 20:45:56.05: [28713]: SEND training at v.27ter fallback mode 2400 bit/s
Jul 26 20:45:56.05: [28713]: <-- [9:AT+FTH=3\r]
Jul 26 20:45:56.13: [28713]: --> [7:CONNECT]
Jul 26 20:45:56.86: [28713]: --> [7:CONNECT]
Jul 26 20:45:58.21: [28713]: --> [2:OK]
Jul 26 20:45:58.21: [28713]: <-- [9:AT+FTS=7\r]
Jul 26 20:45:58.21: [28713]: --> [2:OK]
Jul 26 20:45:58.21: [28713]: <-- [10:AT+FTM=24\r]
Jul 26 20:45:59.46: [28713]: --> [7:CONNECT]
Jul 26 20:46:01.02: [28713]: --> [2:OK]
Jul 26 20:46:01.02: [28713]: <-- [9:AT+FRH=3\r]
Jul 26 20:46:04.13: [28713]: --> [0:]
Jul 26 20:46:04.13: [28713]: MODEM <Empty line>
Jul 26 20:46:04.13: [28713]: --> [2:]
Jul 26 20:46:04.13: [28713]: --> [2:OK]
Jul 26 20:46:04.13: [28713]: DELAY 1500 ms
Jul 26 20:46:05.63: [28713]: TRAINING failed
Jul 26 20:46:05.63: [28713]: <-- [9:AT+FTH=3\r]
Jul 26 20:46:05.71: [28713]: --> [7:CONNECT]
Jul 26 20:46:05.79: [28713]: --> [10:NO CARRIER]
Jul 26 20:46:05.79: [28713]: MODEM No carrier
Jul 26 20:46:05.79: [28713]: <-- [5:ATH0\r]
Jul 26 20:46:05.89: [28713]: --> [2:OK]
Jul 26 20:46:05.89: [28713]: SESSION END


Date: 07/26/02 20:47
Error: Failure to train remote modem at 2400 bps or minimum speed


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*

Follow-Ups:
- Re: [hylafax-users] Failure to train remote modem
  - From: Lee Howard

Prev by Date: [hylafax-users] cannot open /var/spool/hylafax/log/xferfaxlog (No such file or directory)
Next by Date: Re: [hylafax-users] Failure to train remote modem
Previous by thread: Re: [hylafax-users] cannot open /var/spool/hylafax/log/xferfaxlog (No such file or directory)
Next by thread: Re: [hylafax-users] Failure to train remote modem
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services