Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Any ideas about this?
Do you guys have any ideas why this may be happening when I'm trying to send
a fax via WHFC? (the document is a MS Word).
Your facsimile job to 553-7123 was not sent because:
No response to MPS or EOP repeated 3 tries
The job will be retried at 13:15.
---- Transcript of session follows ----
Jul 02 13:12:25.57: [19991]: SESSION BEGIN 00000179 12055537123
Jul 02 13:12:25.57: [19991]: HylaFAX (tm) Version 4.1.2
Jul 02 13:12:25.57: [19991]: SEND FAX: JOB 21 DEST 553-7123 COMMID 00000179
DEVICE '/dev/modem'
Jul 02 13:12:25.57: [19991]: DELAY 75 ms
Jul 02 13:12:25.65: [19991]: DELAY 2600 ms
Jul 02 13:12:28.25: [19991]: <-- [4:ATZ\r]
Jul 02 13:12:29.22: [19991]: --> [2:OK]
Jul 02 13:12:29.22: [19991]: DELAY 3000 ms
Jul 02 13:12:32.22: [19991]: <-- [5:ATE0\r]
Jul 02 13:12:32.23: [19991]: --> [4:ATE0]
Jul 02 13:12:32.23: [19991]: --> [2:OK]
Jul 02 13:12:32.23: [19991]: <-- [5:ATV1\r]
Jul 02 13:12:32.24: [19991]: --> [2:OK]
Jul 02 13:12:32.24: [19991]: <-- [5:ATQ0\r]
Jul 02 13:12:32.25: [19991]: --> [2:OK]
Jul 02 13:12:32.25: [19991]: <-- [7:ATS0=0\r]
Jul 02 13:12:32.27: [19991]: --> [2:OK]
Jul 02 13:12:32.27: [19991]: <-- [7:ATS8=2\r]
Jul 02 13:12:32.29: [19991]: --> [2:OK]
Jul 02 13:12:32.29: [19991]: <-- [8:ATS7=60\r]
Jul 02 13:12:32.31: [19991]: --> [2:OK]
Jul 02 13:12:32.31: [19991]: <-- [12:AT+FCLASS=1\r]
Jul 02 13:12:32.33: [19991]: --> [2:OK]
Jul 02 13:12:32.33: [19991]: <-- [7:ATL3M1\r]
Jul 02 13:12:32.35: [19991]: --> [2:OK]
Jul 02 13:12:32.35: [19991]: <-- [12:AT+FCLASS=1\r]
Jul 02 13:12:32.47: [19991]: --> [2:OK]
Jul 02 13:12:32.47: [19991]: DIAL 5537123
Jul 02 13:12:32.47: [19991]: <-- [12:ATDT5537123\r]
Jul 02 13:12:50.73: [19991]: --> [7:CONNECT]
Jul 02 13:12:52.75: [19991]: --> [2:OK]
Jul 02 13:12:52.75: [19991]: REMOTE NSF "00 00 31 00 CE B8 C4 80 11 85 0D DD
00 00 DD DD 00 00 DD DD 00 00 00 00 00 00 00 00 ED 22 B0 00 00 A4 00 36"
Jul 02 13:12:52.75: [19991]: NSF remote fax equipment: Sharp/Olivetti
Jul 02 13:12:52.75: [19991]: <-- [9:AT+FRH=3\r]
Jul 02 13:12:52.77: [19991]: --> [7:CONNECT]
Jul 02 13:12:53.47: [19991]: --> [2:OK]
Jul 02 13:12:53.47: [19991]: REMOTE CSI "2055535625"
Jul 02 13:12:53.47: [19991]: <-- [9:AT+FRH=3\r]
Jul 02 13:12:53.49: [19991]: --> [7:CONNECT]
Jul 02 13:12:53.82: [19991]: --> [2:OK]
Jul 02 13:12:53.82: [19991]: REMOTE best rate 9600 bit/s
Jul 02 13:12:53.82: [19991]: REMOTE max page width 1728 pixels in 215 mm
Jul 02 13:12:53.82: [19991]: REMOTE max unlimited page length
Jul 02 13:12:53.82: [19991]: REMOTE best vres 7.7 line/mm
Jul 02 13:12:53.82: [19991]: REMOTE best format 2-D MMR
Jul 02 13:12:53.82: [19991]: REMOTE supports T.30 Annex A, ECM
Jul 02 13:12:53.82: [19991]: REMOTE best 20 ms, 10 ms/scanline
Jul 02 13:12:53.82: [19991]: USE 9600 bit/s
Jul 02 13:12:53.82: [19991]: USE 20 ms, 10 ms/scanline
Jul 02 13:12:53.82: [19991]: SEND file "docq/doc21.ps;71"
Jul 02 13:12:53.82: [19991]: USE page width 1728 pixels in 215 mm
Jul 02 13:12:53.82: [19991]: USE unlimited page length
Jul 02 13:12:53.82: [19991]: USE 7.7 line/mm
Jul 02 13:12:53.82: [19991]: USE 2-D MR
Jul 02 13:12:53.82: [19991]: SEND training at v.29 9600 bit/s
Jul 02 13:12:53.82: [19991]: <-- [9:AT+FTH=3\r]
Jul 02 13:12:54.77: [19991]: --> [7:CONNECT]
Jul 02 13:12:54.80: [19991]: --> [7:CONNECT]
Jul 02 13:12:55.89: [19991]: --> [2:OK]
Jul 02 13:12:55.89: [19991]: <-- [9:AT+FTS=7\r]
Jul 02 13:12:55.98: [19991]: --> [2:OK]
Jul 02 13:12:55.98: [19991]: <-- [10:AT+FTM=96\r]
Jul 02 13:12:56.00: [19991]: --> [7:CONNECT]
Jul 02 13:12:57.79: [19991]: --> [2:OK]
Jul 02 13:12:57.79: [19991]: <-- [9:AT+FRH=3\r]
Jul 02 13:12:57.98: [19991]: --> [7:CONNECT]
Jul 02 13:12:59.15: [19991]: --> [2:OK]
Jul 02 13:12:59.15: [19991]: TRAINING succeeded
Jul 02 13:12:59.15: [19991]: DELAY 75 ms
Jul 02 13:12:59.23: [19991]: <-- [10:AT+FTM=96\r]
Jul 02 13:12:59.32: [19991]: --> [7:CONNECT]
Jul 02 13:12:59.32: [19991]: SEND begin page
Jul 02 13:13:11.30: [19991]: SENT 25844 bytes of data
Jul 02 13:13:25.28: [19991]: SENT 25870 bytes of data
Jul 02 13:13:27.27: [19991]: SENT 5504 bytes of data
Jul 02 13:13:27.27: [19991]: SEND 2D RTC
Jul 02 13:13:27.27: [19991]: SEND end page
Jul 02 13:13:32.04: [19991]: --> [2:OK]
Jul 02 13:13:32.04: [19991]: <-- [9:AT+FTS=7\r]
Jul 02 13:13:32.13: [19991]: --> [2:OK]
Jul 02 13:13:32.13: [19991]: SEND send MPS (more pages, same document)
Jul 02 13:13:32.13: [19991]: <-- [9:AT+FTH=3\r]
Jul 02 13:13:33.00: [19991]: --> [7:CONNECT]
Jul 02 13:13:33.32: [19991]: --> [2:OK]
Jul 02 13:13:33.32: [19991]: <-- [9:AT+FRH=3\r]
Jul 02 13:13:33.46: [19991]: --> [7:CONNECT]
Jul 02 13:13:34.63: [19991]: --> [2:OK]
Jul 02 13:13:34.63: [19991]: SEND recv RTN (retrain negative)
Jul 02 13:13:34.63: [19991]: SEND training at v.29 7200 bit/s
Jul 02 13:13:34.63: [19991]: <-- [9:AT+FTH=3\r]
Jul 02 13:13:35.58: [19991]: --> [7:CONNECT]
Jul 02 13:13:35.61: [19991]: --> [7:CONNECT]
Jul 02 13:13:36.70: [19991]: --> [2:OK]
Jul 02 13:13:36.70: [19991]: <-- [9:AT+FTS=7\r]
Jul 02 13:13:36.79: [19991]: --> [2:OK]
Jul 02 13:13:36.79: [19991]: <-- [10:AT+FTM=72\r]
Jul 02 13:13:36.81: [19991]: --> [7:CONNECT]
Jul 02 13:13:38.61: [19991]: --> [2:OK]
Jul 02 13:13:38.61: [19991]: <-- [9:AT+FRH=3\r]
Jul 02 13:13:38.80: [19991]: --> [7:CONNECT]
Jul 02 13:13:39.97: [19991]: --> [2:OK]
Jul 02 13:13:39.97: [19991]: TRAINING succeeded
Jul 02 13:13:39.97: [19991]: DELAY 75 ms
Jul 02 13:13:40.05: [19991]: <-- [10:AT+FTM=72\r]
Jul 02 13:13:40.14: [19991]: --> [7:CONNECT]
Jul 02 13:13:40.14: [19991]: SEND begin page
Jul 02 13:13:48.13: [19991]: SENT 19322 bytes of data
Jul 02 13:14:00.11: [19991]: SENT 19379 bytes of data
Jul 02 13:14:06.10: [19991]: SENT 14785 bytes of data
Jul 02 13:14:06.10: [19991]: SEND 2D RTC
Jul 02 13:14:06.10: [19991]: SEND end page
Jul 02 13:14:09.33: [19991]: --> [2:OK]
Jul 02 13:14:09.33: [19991]: <-- [9:AT+FTS=7\r]
Jul 02 13:14:09.42: [19991]: --> [2:OK]
Jul 02 13:14:09.42: [19991]: SEND send MPS (more pages, same document)
Jul 02 13:14:09.42: [19991]: <-- [9:AT+FTH=3\r]
Jul 02 13:14:10.29: [19991]: --> [7:CONNECT]
Jul 02 13:14:10.61: [19991]: --> [2:OK]
Jul 02 13:14:10.61: [19991]: <-- [9:AT+FRH=3\r]
Jul 02 13:14:13.71: [19991]: --> [0:]
Jul 02 13:14:13.71: [19991]: MODEM <Empty line>
Jul 02 13:14:13.72: [19991]: --> [2:]
Jul 02 13:14:13.72: [19991]: --> [2:OK]
Jul 02 13:14:13.72: [19991]: SEND send MPS (more pages, same document)
Jul 02 13:14:13.72: [19991]: <-- [9:AT+FTH=3\r]
Jul 02 13:14:14.65: [19991]: --> [7:CONNECT]
Jul 02 13:14:14.97: [19991]: --> [2:OK]
Jul 02 13:14:14.97: [19991]: <-- [9:AT+FRH=3\r]
Jul 02 13:14:16.01: [19991]: --> [7:CONNECT]
Jul 02 13:14:21.02: [19991]: --> [2:]
Jul 02 13:14:21.02: [19991]: --> [2:OK]
Jul 02 13:14:21.02: [19991]: SEND send MPS (more pages, same document)
Jul 02 13:14:21.02: [19991]: <-- [9:AT+FTH=3\r]
Jul 02 13:14:21.95: [19991]: --> [7:CONNECT]
Jul 02 13:14:22.27: [19991]: --> [2:OK]
Jul 02 13:14:22.27: [19991]: <-- [9:AT+FRH=3\r]
Jul 02 13:14:25.37: [19991]: --> [0:]
Jul 02 13:14:25.37: [19991]: MODEM <Empty line>
Jul 02 13:14:25.38: [19991]: --> [2:]
Jul 02 13:14:25.38: [19991]: --> [2:OK]
Jul 02 13:14:25.38: [19991]: No response to MPS or EOP repeated 3 tries
Jul 02 13:14:25.38: [19991]: <-- [9:AT+FTH=3\r]
Jul 02 13:14:26.31: [19991]: --> [7:CONNECT]
Jul 02 13:14:26.63: [19991]: --> [2:OK]
Jul 02 13:14:26.63: [19991]: <-- [5:ATH0\r]
Jul 02 13:14:28.03: [19991]: --> [2:OK]
Jul 02 13:14:28.03: [19991]: SESSION END
The fax never goes......
-------------------------------------
Joe W. Guy, Jr.
Information Systems Manager
MCP, A+, Network+
-------------------------------------
AMH Credit Union
205.556.8860 Ext.304
http://www.amhcu.org
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null