[hylafax-users] problem after upgrade to 4.1.2

To: hylafax-users@hylafax.org
Subject: [hylafax-users] problem after upgrade to 4.1.2
From: Purwanto <purwanto@makro.co.id>
Date: Tue, 2 Jul 2002 07:49:18 +0700 (JAVT)

 Hi all..

 I just upgrade hylafax to ver 4.1.2, after that i could not sent any fax
 from windows or from local server.
 Modem like do handsake, ant then stop, i use AT&T dataport express modem.

 here a log file :

     ---- Transcript of session follows ----

 Jul 01 16:37:30.52: [16767]: SESSION BEGIN 00000085 62217306
 Jul 01 16:37:30.52: [16767]: HylaFAX (tm) Version 4.1.2
 Jul 01 16:37:30.52: [16767]: SEND FAX: JOB 29 DEST 7306 COMMID 00000085
 DEVICE '/dev/ttyS1'
 Jul 01 16:37:30.52: [16767]: MODEM set DTR OFF
 Jul 01 16:37:30.52: [16767]: DELAY 75 ms
 Jul 01 16:37:30.60: [16767]: MODEM set DTR ON
 Jul 01 16:37:30.60: [16767]: DELAY 2600 ms
 Jul 01 16:37:33.20: [16767]: MODEM set baud rate: 19200 baud, input
 flow RTS/CTS, output flow RTS/CTS
 Jul 01 16:37:33.20: [16767]: MODEM flush i/o
 Jul 01 16:37:33.20: [16767]: <-- [4:ATZ\r]
 Jul 01 16:37:34.02: [16767]: --> [2:OK]
 Jul 01 16:37:34.02: [16767]: DELAY 3000 ms
 Jul 01 16:37:37.02: [16767]: <-- [5:ATE0\r]
 Jul 01 16:37:37.14: [16767]: --> [4:ATE0]
 Jul 01 16:37:37.14: [16767]: --> [2:OK]
 Jul 01 16:37:37.14: [16767]: <-- [5:ATV1\r]
 Jul 01 16:37:37.26: [16767]: --> [2:OK]
 Jul 01 16:37:37.26: [16767]: <-- [5:ATQ0\r]
 Jul 01 16:37:37.38: [16767]: --> [2:OK]
 Jul 01 16:37:37.38: [16767]: <-- [7:ATS0=0\r]
 Jul 01 16:37:37.50: [16767]: --> [2:OK]
 Jul 01 16:37:37.50: [16767]: <-- [7:ATS8=2\r]
 Jul 01 16:37:37.62: [16767]: --> [2:OK]
 Jul 01 16:37:37.62: [16767]: <-- [8:ATS7=60\r]
 Jul 01 16:37:37.74: [16767]: --> [2:OK]
 Jul 01 16:37:37.74: [16767]: <-- [12:AT&R0\D1\Q3\r]
 Jul 01 16:37:37.86: [16767]: --> [2:OK]
 Jul 01 16:37:37.86: [16767]: <-- [6:AT&D2\r]
 Jul 01 16:37:37.98: [16767]: --> [2:OK]
 Jul 01 16:37:37.98: [16767]: <-- [6:AT&C1\r]
 Jul 01 16:37:38.10: [16767]: --> [2:OK]
 Jul 01 16:37:38.10: [16767]: <-- [12:AT+FCLASS=1\r]
 Jul 01 16:37:38.22: [16767]: --> [2:OK]
 Jul 01 16:37:38.22: [16767]: <-- [9:AT+FAA=0\r]
 Jul 01 16:37:38.34: [16767]: --> [2:OK]
 Jul 01 16:37:38.34: [16767]: <-- [7:ATL0M1\r]
 Jul 01 16:37:38.46: [16767]: --> [2:OK]
 Jul 01 16:37:38.46: [16767]: MODEM input buffering enabled
 Jul 01 16:37:38.46: [16767]: <-- [12:AT+FCLASS=1\r]
 Jul 01 16:37:38.68: [16767]: --> [2:OK]
 Jul 01 16:37:38.68: [16767]: DIAL 7306
 Jul 01 16:37:38.68: [16767]: <-- [9:ATDT7306\r]
 Jul 01 16:37:55.72: [16767]: --> [7:CONNECT]
 Jul 01 16:37:55.72: [16767]: MODEM input buffering disabled
 Jul 01 16:37:58.44: [16767]: --> HDLC<39:FF C0 04 00 00 8C 00 72 1D 00 21
B0 BB 00 00 BB BB 00 00 BB BB BB BB BB 40 E0 80 80 68 44 08 B7 44 09 00 00
08 20 34>
 Jul 01 16:37:58.44: [16767]: --> [2:OK]
 Jul 01 16:37:58.44: [16767]: REMOTE NSF "00 00 31 00 4E B8 00 84 0D DD 00
00 DD DD 00 00 DD DD DD DD DD 02 07 01 01 16 22 10 ED 22 90 00 00 10 04 2C
00"
 Jul 01 16:37:58.44: [16767]: NSF remote fax equipment: Sharp/Olivetti
 Jul 01 16:37:58.44: [16767]: <-- [9:AT+FRH=3\r]
 Jul 01 16:37:58.45: [16767]: --> [7:CONNECT]
 Jul 01 16:37:58.47: [16767]: --> HDLC<25:FF C0 02 4C 1C 0C 2C 8C 6C 2C 04
8C 4C 0C 04 04 04 04 04 04 04 04 04 AC 28>
 Jul 01 16:37:58.47: [16767]: --> [2:OK]
 Jul 01 16:37:58.47: [16767]: REMOTE CSI "021 4614082"
 Jul 01 16:37:58.47: [16767]: <-- [9:AT+FRH=3\r]
 Jul 01 16:37:58.48: [16767]: --> [7:CONNECT]
 Jul 01 16:37:58.49: [16767]: --> HDLC<9:FF C8 01 00 72 1D 00 71 24>
 Jul 01 16:37:58.49: [16767]: --> [2:OK]
 Jul 01 16:37:58.49: [16767]: REMOTE best rate 9600 bit/s
 Jul 01 16:37:58.49: [16767]: REMOTE max page width 1728 pixels in 215 mm
 Jul 01 16:37:58.49: [16767]: REMOTE max unlimited page length
 Jul 01 16:37:58.49: [16767]: REMOTE best vres 7.7 line/mm
 Jul 01 16:37:58.49: [16767]: REMOTE best format 1-D MR
 Jul 01 16:37:58.49: [16767]: REMOTE best 20 ms, 10 ms/scanline
 Jul 01 16:37:58.49: [16767]: USE 9600 bit/s
 Jul 01 16:37:58.49: [16767]: USE 20 ms, 10 ms/scanline
 Jul 01 16:37:58.49: [16767]: SEND file "docq/doc28.ps;01"
 Jul 01 16:37:58.49: [16767]: USE page width 1728 pixels in 215 mm
 Jul 01 16:37:58.49: [16767]: USE unlimited page length
 Jul 01 16:37:58.49: [16767]: USE 7.7 line/mm
 Jul 01 16:37:58.49: [16767]: USE 1-D MR
 Jul 01 16:37:58.49: [16767]: SEND training at v.29 9600 bit/s
 Jul 01 16:37:58.49: [16767]: <-- [9:AT+FTH=3\r]
 Jul 01 16:37:58.51: [16767]: --> [7:CONNECT]
 Jul 01 16:37:58.51: [16767]: <-- HDLC<23:FF C0 C2 AC EC 0C 2C 0C 2C 1C 8C
4C 4C 6C D4 04 04 04 04 04 04 04 04>
 Jul 01 16:38:00.21: [16767]: --> [7:CONNECT]
 Jul 01 16:38:00.21: [16767]: <-- HDLC<6:FF C8 C1 00 62 10>
 Jul 01 16:38:00.53: [16767]: --> [2:OK]
 Jul 01 16:38:00.53: [16767]: <-- [9:AT+FTS=7\r]
 Jul 01 16:38:00.61: [16767]: --> [2:OK]
 Jul 01 16:38:00.61: [16767]: <-- [10:AT+FTM=96\r]
 Jul 01 16:38:00.74: [16767]: -->
[41:3,24,48,72,73,74,96,97,98,121,122,145,146]
 Jul 01 16:38:00.74: [16767]: --> [5:ERROR]
 Jul 01 16:38:00.74: [16767]: MODEM Command error
 Jul 01 16:38:00.74: [16767]: Problem sending TCF data
 Jul 01 16:38:00.74: [16767]: <-- [9:AT+FRH=3\r]
 Jul 01 16:38:00.86: [16767]: --> [5:ERROR]
 Jul 01 16:38:00.86: [16767]: MODEM Command error
 Jul 01 16:38:00.86: [16767]: DELAY 1500 ms
 Jul 01 16:38:02.36: [16767]: SEND training at v.29 7200 bit/s
 Jul 01 16:38:02.36: [16767]: <-- [9:AT+FTH=3\r]
 Jul 01 16:38:02.48: [16767]: --> [5:ERROR]
 Jul 01 16:38:02.48: [16767]: Error sending T.30 prologue frames
 Jul 01 16:38:02.48: [16767]: SEND training at v.27ter 4800 bit/s
 Jul 01 16:38:02.48: [16767]: <-- [9:AT+FTH=3\r]
 Jul 01 16:38:02.60: [16767]: --> [5:ERROR]
 Jul 01 16:38:02.60: [16767]: Error sending T.30 prologue frames
 Jul 01 16:38:02.60: [16767]: SEND training at v.27ter fallback mode 2400
bit/s
 Jul 01 16:38:02.60: [16767]: <-- [9:AT+FTH=3\r]
 Jul 01 16:38:02.72: [16767]: --> [5:ERROR]
 Jul 01 16:38:02.72: [16767]: Error sending T.30 prologue frames
 Jul 01 16:38:02.72: [16767]: TRAINING failed
 Jul 01 16:38:02.72: [16767]: <-- [9:AT+FTH=3\r]
 Jul 01 16:38:02.84: [16767]: --> [5:ERROR]
 Jul 01 16:38:02.84: [16767]: MODEM input buffering enabled
 Jul 01 16:38:02.84: [16767]: <-- [5:ATH0\r]
 Jul 01 16:38:03.76: [16767]: --> [2:OK]
 Jul 01 16:38:03.76: [16767]: MODEM set DTR OFF
 Jul 01 16:38:03.76: [16767]: SESSION END

 regards

 Purwanto


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null

Follow-Ups:
- Re: [hylafax-users] problem after upgrade to 4.1.2
  - From: Lee Howard

Prev by Date: Re: [hylafax-users] modem is wedged?
Next by Date: Re: [hylafax-users] Small typeface faxing from filepro
Previous by thread: Re: [hylafax-users] modem is wedged?
Next by thread: Re: [hylafax-users] problem after upgrade to 4.1.2
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services