|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Problems when receiving (sending is ok)
Hello everybody,
I´m running hylafax 4.1 on Slackware 8 (kernel 2.2.19), modem is Class 2 Rockwell RC32ACL-based.
I did not compile the package, instead I downloaded the binary available from hylafax.org.
Whenever I receive a fax, first page comes through but then the process stalls (until I abort it) and the modem stays in state "Receiving from ...".
Here is one such log (from intercontinental fax):
Jun 25 05:14:21.27: [ 177]: SESSION BEGIN 00000039 5062235001
Jun 25 05:14:21.27: [ 177]: <-- [4:ATA\r]
Jun 25 05:14:24.83: [ 177]: --> [3:FAX]
Jun 25 05:14:31.23: [ 177]: --> [5:+FCON]
Jun 25 05:14:31.23: [ 177]: ANSWER: FAX CONNECTION
Jun 25 05:14:31.23: [ 177]: RECV FAX: begin
Jun 25 05:14:32.88: [ 177]: --> [29:+FTSI: " +49 2191 967946"]
Jun 25 05:14:32.88: [ 177]: REMOTE TSI "+49 2191 967946"
Jun 25 05:14:33.17: [ 177]: --> [22:+FDCS: 0,3,0,2,1,0,0,3]
Jun 25 05:14:33.17: [ 177]: REMOTE wants 9600 bit/s
Jun 25 05:14:33.17: [ 177]: REMOTE wants page width 1728 pixels in 215 mm
Jun 25 05:14:33.17: [ 177]: REMOTE wants unlimited page length
Jun 25 05:14:33.17: [ 177]: REMOTE wants 3.85 line/mm
Jun 25 05:14:33.17: [ 177]: REMOTE wants 2-D MR
Jun 25 05:14:33.28: [ 177]: --> [2:OK]
Jun 25 05:14:33.28: [ 177]: <-- [7:AT+FDR\r]
Jun 25 05:14:34.89: [ 177]: --> [5:+FCFR]
Jun 25 05:14:37.83: [ 177]: --> [22:+FDCS: 0,3,0,2,1,0,0,3]
Jun 25 05:14:37.83: [ 177]: REMOTE wants 9600 bit/s
Jun 25 05:14:37.83: [ 177]: REMOTE wants page width 1728 pixels in 215 mm
Jun 25 05:14:37.83: [ 177]: REMOTE wants unlimited page length
Jun 25 05:14:37.83: [ 177]: REMOTE wants 3.85 line/mm
Jun 25 05:14:37.83: [ 177]: REMOTE wants 2-D MR
Jun 25 05:14:37.83: [ 177]: --> [7:CONNECT]
Jun 25 05:14:37.83: [ 177]: RECV: begin page
Jun 25 05:14:37.83: [ 177]: RECV: send trigger 022
Jun 25 05:14:37.83: [ 177]: <-- data [1]
Jun 25 05:14:56.27: [ 177]: RECV: 1149 total lines, 0 bad lines, 0 consecutive bad lines
Jun 25 05:14:56.27: [ 177]: --> [17:+FPTS: 1,2219,0,0]
Jun 25 05:14:57.51: [ 177]: --> [7:+FET: 2]
Jun 25 05:14:57.51: [ 177]: RECV recv EOP (no more pages or documents)
Jun 25 05:14:57.62: [ 177]: --> [2:OK]
------> Here it stalls, notice time until I realized and intervened with faxstate.
Jun 25 10:57:25.97: [ 177]: STATE "R"
Jun 25 11:42:38.59: [ 177]: STATE "R"
Jun 25 18:14:08.94: [ 177]: CLOSE /dev/ttyS2
This other one is similar (from local fax):
Jun 26 11:44:33.29: [ 1304]: SESSION BEGIN 00000044 5062235001
Jun 26 11:44:33.29: [ 1304]: <-- [4:ATA\r]
Jun 26 11:44:45.00: [ 1304]: --> [3:FAX]
Jun 26 11:44:51.07: [ 1304]: --> [5:+FCON]
Jun 26 11:44:51.07: [ 1304]: ANSWER: FAX CONNECTION
Jun 26 11:44:51.07: [ 1304]: RECV FAX: begin
Jun 26 11:44:52.70: [ 1304]: --> [29:+FTSI: " 506 2220278"]
Jun 26 11:44:52.70: [ 1304]: REMOTE TSI "506 2220278"
Jun 26 11:44:53.01: [ 1304]: --> [22:+FDCS: 0,3,0,2,0,0,0,3]
Jun 26 11:44:53.01: [ 1304]: REMOTE wants 9600 bit/s
Jun 26 11:44:53.01: [ 1304]: REMOTE wants page width 1728 pixels in 215 mm
Jun 26 11:44:53.01: [ 1304]: REMOTE wants unlimited page length
Jun 26 11:44:53.01: [ 1304]: REMOTE wants 3.85 line/mm
Jun 26 11:44:53.01: [ 1304]: REMOTE wants 1-D MR
Jun 26 11:44:53.12: [ 1304]: --> [2:OK]
Jun 26 11:44:53.12: [ 1304]: <-- [7:AT+FDR\r]
Jun 26 11:44:54.75: [ 1304]: --> [5:+FCFR]
Jun 26 11:44:58.30: [ 1304]: --> [22:+FDCS: 0,3,0,2,0,0,0,3]
Jun 26 11:44:58.30: [ 1304]: REMOTE wants 9600 bit/s
Jun 26 11:44:58.30: [ 1304]: REMOTE wants page width 1728 pixels in 215 mm
Jun 26 11:44:58.30: [ 1304]: REMOTE wants unlimited page length
Jun 26 11:44:58.30: [ 1304]: REMOTE wants 3.85 line/mm
Jun 26 11:44:58.30: [ 1304]: REMOTE wants 1-D MR
Jun 26 11:44:58.30: [ 1304]: --> [7:CONNECT]
Jun 26 11:44:58.30: [ 1304]: RECV: begin page
Jun 26 11:44:58.30: [ 1304]: RECV: send trigger 022
Jun 26 11:44:58.30: [ 1304]: <-- data [1]
Jun 26 11:45:37.94: [ 1304]: RECV: 1163 total lines, 1 bad lines, 1 consecutive bad lines
Jun 26 11:45:37.94: [ 1304]: --> [17:+FPTS: 1,2219,0,0]
Jun 26 11:45:39.32: [ 1304]: --> [7:+FET: 0]
Jun 26 11:45:39.32: [ 1304]: RECV recv MPS (more pages, same document)
Jun 26 11:45:39.32: [ 1304]: --> [2:OK]
--------> Here I was monitoring so reacted sooner (this time properly with faxabort)
Jun 26 11:47:07.21: [ 1304]: ABORT: job abort requested
Jun 26 11:47:07.22: [ 1304]: RECV FAX (00000044): recvq/fax00012.tif from 506 2220278, route to <unspecified>, 0 pages in 2:16
Jun 26 11:47:07.22: [ 1304]: RECV FAX: Receive aborted due to operator intervention
Jun 26 11:47:07.22: [ 1304]: <-- [6:AT+FK\r]
Jun 26 11:47:07.31: [ 1304]: --> [10:+FHNG: 100]
Jun 26 11:47:07.31: [ 1304]: REMOTE HANGUP: Unspecified Phase D error (code 100)
Jun 26 11:47:07.31: [ 1304]: --> [2:OK]
Jun 26 11:47:07.31: [ 1304]: RECV FAX (00000044): session with 506 2220278 terminated abnormally: Receive aborted due to operator intervention
Jun 26 11:47:07.31: [ 1304]: RECV FAX: bin/faxrcvd "recvq/fax00012.tif" "ttyS2" "00000044" "Receive aborted due to operator intervention"
Jun 26 11:47:07.62: [ 1304]: RECV FAX: end
Jun 26 11:47:07.62: [ 1304]: SESSION END
Any help will be greatly appreciated.
Regards,
Gunther Wenzel
Saludos,
Gunther Wenzel
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
