|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] U.S. Robotics 56K Message Settings...
sometimes..it run
frequently error (99%) : Timeout or Busy
thanks a lot
alain
ati4
U.S. Robotics 56K Message Settings...
B0 E1 F1 L1 M0 Q0 V1 X4 Y0
BAUD=38400 PARITY=N WORDLEN=8
DIAL=PULSE ON HOOK
&A3 &B1 &C1 &D2 &H1 &I0 &K1
&M4 &N0 &P1 &R2 &S0 &T5 &U0 &Y1
S00=000 S01=000 S02=043 S03=013 S04=010 S05=008 S06=002
S07=045 S08=002 S09=006 S10=014 S11=070 S12=050 S13=000
S15=000 S16=000 S18=000 S19=000 S21=010 S22=017 S23=019
S25=005 S27=017 S28=008 S29=020 S30=000 S31=128 S32=002
S33=000 S34=000 S35=000 S36=014 S38=000 S39=012 S40=000
S41=004 S42=000 S43=112
LAST DIALED #:
OK
ati7
Configuration Profile...
Product type France External
Product ID: 06566800
Options V32bis,V.34+,x2,V.90
Fax Options Class 1/Class 2.0
Voice Options Speaker Phone, TAD
Clock Freq 92.0Mhz
EPROM 256k
RAM 32k
FLASH date 2/13/98
FLASH rev 12.1.12
DSP date 2/13/98
DSP rev 12.1.12
OK
config.ttyS1
# $Id: usr-xon,v 1.6 2002/04/07 20:29:27 darren Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names
of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
# Configuration for using the Class 1 command interface with
# a USR Courier or Sportster modem and XON/XOFF flow control.
#
#
CountryCode: 33
AreaCode: 4
FAXNumber: +33.xxxxxxxx
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 0
SpeakerVolume: on
GettyArgs: "-h %l dx_%s"
LocalIdentifier: +33.xxxxxxxxx
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # use class 1 interface
ModemRate: 9600 # rate for DCE-DTE communication
ModemFlowControl: xonxoff # hardware flow control
#
ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or
not)
ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for no flow control
ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow
control
ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow
control
ModemResultCodesCmd: ATQ0X4 # enable result codes
#
ModemMfrQueryCmd: !USR
ModemModelQueryCmd: ATI3
ModemRevQueryCmd: ATI7 # XXX returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd: AT&H0&I0&R1 # setup modem for no flow control
Class1HFLOCmd: AT&H1&I0&R2 # setup modem for hardware flow
control
Class1SFLOCmd: "" # modem does this automatically
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd: AT+FCLASS=0 # leave modem idling in class 0
ModemAnswerCmd: AT+FCLASS=1A # answer in Class 1
#
# Disables the reporting of bad frames by the modem. This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd: AT+FNR=1,1,1,0
-----Message d'origine-----
De : hylafax-users-bounce@hylafax.org
[mailto:hylafax-users-bounce@hylafax.org]De la part de Pedro Rocadas
Envoye : jeudi 20 juin 2002 15:42
A : hylafax-users@hylafax.org
Objet : Re: [hylafax-users] U.S. Robotics 56K Message Settings...
--- Alain Siani <ASiani@wanadoo.fr> wrote:
> I have a lot of problem grrrrrrrrr.....
>
>
> JID Pri S Owner Number Pages Dials TTS
> Status
> 3 126 S uucp 00491598950 0:1 1:12 12:53
> No answer (T.30 T1 timeou
>
>
> thks a lot
> Alain
Jay is one of the guys who can give you the best
technical explanation to that message. But is a
comunication issue, like the remote fax machine is not
answering(?), no fax at all(?), there is a fax machine
that answer but unable to connect...oh, and you
configure that USR modem in Class1 right?
__________________________________________________
Do You Yahoo!?
Yahoo! - Official partner of 2002 FIFA World Cup
http://fifaworldcup.yahoo.com
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
