|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] SV: Rockwell / Conexant:
Hi!
I had the same for a long time.
Can you send me the whole log? Especially that "...." part which you cut
off below.
Dobos Sandor
IBCnet Hungary Ltd.
"Johan Ekenberg"
<johan@ekenberg.se> To: "Dustin Butler" <dustin@intrcomm.net>, <faxguy@deanox.com>
Sent by: cc: <hylafax-users@hylafax.org>
hylafax-users-bounce@h Subject: [hylafax-users] SV: Rockwell / Conexant:
ylafax.org
2002.04.17 12:51
Yes, I've also tried this but unfortunately it doesn't help.
/Johan
> I added a -1 (that's a one) to the sendfax command and it seemed
> to fix the problem for me. I had some numbers that would send
> one page and then send MPS with no response back.
>
>
> from the sendfax man page
>
> -1 Transmit facsimile documents using 1-D MR compression. By
> default HylaFAX will use the optimal compression scheme supported
> by the transmitting modem and receiving facsimile device.
>
>
> ------Original Message------
> From: Lee Howard <faxguy@deanox.com>
> Date: Tuesday, April 16th, 2002 5:01 PM CDT
> To: Johan Ekenberg <johan@ekenberg.se>
> Subject: Re: [hylafax-users] Rockwell / Conexant: "No response
> to MPS ..." and other problems
>
> On 2002.04.12 09:06 Johan Ekenberg wrote:
> > Hi!
> >
> > I just built and installed Hylafax 4.1.1 on a Slackware 8.0
> Linux system.
> > The modem is branded "Bestmatic", and it seems to have a
> > Rockwell/Conexant chipset. Installation and configuration went smoothly
> > until I tried to send faxes. I'm trying to fax to a HP
> OfficeJet G85 Fax,
> > but it won't work:
> >
> > - If I send only one page everything looks ok on the Hylafax-side. On
> > the HP side the fax seems to be received ok but then it's never printed
> > (!!).
>
> Probably due to an error before page data transmission.
>
> > - If I send two or more pages I get the infamous "No response
> to MPS or
> > EOP repeated 3 times".
>
> Timing. Same problem as above. See below.
>
> > - I've tried to use both Class 1 and Class 2, but no difference.
>
> Stick with Class 1.
>
> > e) The logfile from sending 1 page. Everything seems to work well,
but
> > the fax is never printed on the receiving side (HP OfficeJet).
> If this is
> > a HP problem I've never experienced it or heard about it before.
> > f) The logfile from sending 2 pages. No response to MPS... etc.
>
> These are both the same problem: timing.
> ....
> > Apr 12 15:33:23.85: [ 1171]: <-- [9:AT+FRH=3r]
> > Apr 12 15:33:24.26: [ 1171]: --> [7:CONNECT]
> > Apr 12 15:33:25.16: [ 1171]: --> [2:OK]
> > Apr 12 15:33:25.16: [ 1171]: TRAINING succeeded
>
> This is the last time we hear from the remote.
>
> > Apr 12 15:33:25.16: [ 1171]: DELAY 75 ms
>
> This is Class1SendMsgDelay.
>
> > Apr 12 15:33:25.24: [ 1171]: <-- [11:AT+FTM=146r]
> > Apr 12 15:33:25.28: [ 1171]: --> [7:CONNECT]
> > Apr 12 15:33:25.28: [ 1171]: SEND begin page
> ....
> > Apr 12 15:33:37.57: [ 1171]: SENT 23525 bytes of data
> > Apr 12 15:33:37.57: [ 1171]: SEND 1D RTC
> > Apr 12 15:33:37.57: [ 1171]: <-- data [29]
> > Apr 12 15:33:37.57: [ 1171]: <-- data [2]
> > Apr 12 15:33:37.57: [ 1171]: SEND end page
> > Apr 12 15:33:40.46: [ 1171]: --> [2:OK]
> > Apr 12 15:33:40.46: [ 1171]: <-- [9:AT+FTS=7r]
> > Apr 12 15:33:40.55: [ 1171]: --> [2:OK]
> > Apr 12 15:33:40.55: [ 1171]: SEND send MPS (more pages, same document)
> > Apr 12 15:33:40.55: [ 1171]: <-- [9:AT+FTH=3r]
> > Apr 12 15:33:40.59: [ 1171]: --> [7:CONNECT]
> > Apr 12 15:33:40.59: [ 1171]: <-- data [3]
> > Apr 12 15:33:40.59: [ 1171]: <-- data [2]
> > Apr 12 15:33:41.89: [ 1171]: --> [2:OK]
>
> All of this has been pure transmission, and so we've not heard a peep
> (intentionally) from the remote.
>
> > Apr 12 15:33:41.89: [ 1171]: <-- [9:AT+FRH=3r]
> > Apr 12 15:33:44.99: [ 1171]: --> [0:]
> > Apr 12 15:33:44.99: [ 1171]: MODEM <Empty line>
>
> And now, when we want to hear from the remote - it's not there. It may
> still be connected, but it's not expecting MPS. It's expecting something
> else.
>
> Try changing Class1SendMsgDelay in your config file. Try 95 and
> 55 ms (75
> is default).
>
> Lee.
>
> ____________________ HylaFAX(tm) Users Mailing List
> _______________________
> To subscribe/unsubscribe, click
http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
