|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Rockwell / Conexant: "No response to MPS ..." and other problems
Hi!
I just built and installed Hylafax 4.1.1 on a Slackware 8.0 Linux system. The modem is branded "Bestmatic", and it seems to have a Rockwell/Conexant chipset. Installation and configuration went smoothly until I tried to send faxes. I'm trying to fax to a HP OfficeJet G85 Fax, but it won't work:
- If I send only one page everything looks ok on the Hylafax-side. On the HP side the fax seems to be received ok but then it's never printed (!!).
- If I send two or more pages I get the infamous "No response to MPS or EOP repeated 3 times".
- I've tried to use both Class 1 and Class 2, but no difference.
I'm a newbie when it comes to (Hyla)faxes and modems so I don't exactly know what info to send. Below is:
a) How faxaddmodem identifies the modem
b) From config.modem when trying Class 1
c) From config.modem when trying Class 2
d) The output from "probemodem"
e) The logfile from sending 1 page. Everything seems to work well, but the fax is never printed on the receiving side (HP OfficeJet). If this is a HP problem I've never experienced it or heard about it before.
f) The logfile from sending 2 pages. No response to MPS... etc.
Please help me, I really want to use Hylafax! If you need any more information I'll be happy to provide it.
Regards,
/Johan Ekenberg - Sweden
------ Logs and info ------
===== faxaddmodem gives this identification of the chipset:
Hmm, this looks like a Class 1 modem.
Product code (ATI0) is "56000".
Other information (ATI3) is "P2107-V90".
Modem manufacturer is "Rockwell/Conexant".
Modem model is "AC/K56".
===== Class 1 config.modem
# Configuration for a Rockwell RC288DPi-based Class 1 modem.
# Hayes Optima 28800 firmware rev ???
# Microcom DeskPorte 28.8S firmware rev V1.100K-V34_DS
# PPI PM288FXMT firmware rev 1.57
...
ModemType: Class1 # use this to supply a hint
ModemRate: 38400 # rate for DCE-DTE communication
ModemFlowControl: rtscts # default
#
ModemNoFlowCmd: AT&K0 # setup no flow control
ModemHardFlowCmd: AT&K3 # setup hardware flow control
ModemSoftFlowCmd: AT&K4 # setup software flow control
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)#
ModemMfrQueryCmd: !Rockwell
ModemModelQueryCmd: !RC288DPi
ModemRevQueryCmd: ATI3 # product information
#
ModemDialCmd: ATDT%s # T for tone dialing
===== Class 2 config.modem:
# Configuration for a Rockwell AC/K56-based Class 2 modem.
# based upon work of Mark J. Bailey, Jonathan Mau and Glenn Burkhardt.
# Multitech MT5600ZDX
# Diamond Multimedia SupraExpress 56e PRO
# Zoom Telephonics 56Kx
# (and others)
...
ModemType: Class2 # use class 2 interface
ModemRate: 38400
ModemFlowControl: xonxoff # default
ModemWaitForConnect: yes # wait for CONNECT on answer
#
#ModemResetCmds: AT&F2 # what you want for a Supra
ModemNoFlowCmd: AT&K # disable flow control cmd
ModemHardFlowCmd: AT&K3 # hardware flow control cmd
ModemSoftFlowCmd: AT&K4 # software flow control cmd
ModemSetupDTRCmd: AT&D3 # DTR off causes modem to reset
ModemSetupDCDCmd: AT&C1 # DCD follows carrier
ModemSetupAACmd: AT+FCLASS=0;+FAA=1 # enable in class 0
#
ModemSendFillOrder: LSB2MSB # as expected
ModemRecvFillOrder: MSB2LSB # opposite of what makes sense
Class2RecvDataTrigger: "\022" # a la 2388-B
===== probemodem:
Probing for best speed to talk to modem: 38400 OK.
This looks like a Class 1 modem.
ATI0 RESULT = "OK" RESPONSE = "56000"
ATI1 RESULT = "OK" RESPONSE = "030"
ATI2 RESULT = "OK" RESPONSE = "OK"
ATI3 RESULT = "OK" RESPONSE = "P2107-V90"
Class 1 stuff...
AT+FCLASS=? RESULT = "OK" RESPONSE = "0,1,1.0,2,8,10"
AT+FCLASS? RESULT = "OK" RESPONSE = "1"
AT+FCLASS=0 RESULT = "OK" RESPONSE = "OK"
AT+FCLASS=1 RESULT = "OK" RESPONSE = "OK"
AT+FCLASS? RESULT = "OK" RESPONSE = "1"
AT+FJUNK=? RESULT = "ERROR" RESPONSE = "ERROR"
AT+FJUNK? RESULT = "ERROR" RESPONSE = "ERROR"
AT+FAA=? RESULT = "ERROR" RESPONSE = "ERROR"
AT+FAA? RESULT = "ERROR" RESPONSE = "ERROR"
AT+FAE=? RESULT = "OK" RESPONSE = "(0,1)"
AT+FAE? RESULT = "OK" RESPONSE = "0"
AT+FTH=? RESULT = "OK" RESPONSE = "3,24,48,72,73,74,96,97,98,121,122,145,146"
AT+FRH=? RESULT = "OK" RESPONSE = "3,24,48,72,73,74,96,97,98,121,122,145,146"
AT+FTM=? RESULT = "OK" RESPONSE = "3,24,48,72,73,74,96,97,98,121,122,145,146"
AT+FRM=? RESULT = "OK" RESPONSE = "3,24,48,72,73,74,96,97,98,121,122,145,146"
AT+FTS=? RESULT = "ERROR" RESPONSE = "ERROR"
AT+FRS=? RESULT = "ERROR" RESPONSE = "ERROR"
===== Logfile from trying to send 1 page to a HP OfficeJet G85 Fax Machine (where everything looks ok when sending, but the fax is never printed (!?)
Apr 12 15:24:57.52: [ 938]: SESSION BEGIN 00000006 46317043887
Apr 12 15:24:57.52: [ 938]: HylaFAX (tm) Version 4.1.1
Apr 12 15:24:57.52: [ 938]: SEND FAX: JOB 4 DEST 7043887 COMMID 00000006 DEVICE '/dev/modem'
Apr 12 15:24:57.52: [ 938]: DELAY 75 ms
Apr 12 15:24:57.60: [ 938]: DELAY 2600 ms
Apr 12 15:25:00.20: [ 938]: <-- [4:ATZ\r]
Apr 12 15:25:00.29: [ 938]: --> [2:OK]
Apr 12 15:25:00.29: [ 938]: DELAY 3000 ms
Apr 12 15:25:03.29: [ 938]: <-- [5:ATE0\r]
Apr 12 15:25:03.30: [ 938]: --> [4:ATE0]
Apr 12 15:25:03.30: [ 938]: --> [2:OK]
Apr 12 15:25:03.30: [ 938]: <-- [5:ATV1\r]
Apr 12 15:25:03.32: [ 938]: --> [2:OK]
Apr 12 15:25:03.32: [ 938]: <-- [5:ATQ0\r]
Apr 12 15:25:03.34: [ 938]: --> [2:OK]
Apr 12 15:25:03.34: [ 938]: <-- [7:ATS0=0\r]
Apr 12 15:25:03.36: [ 938]: --> [2:OK]
Apr 12 15:25:03.36: [ 938]: <-- [7:ATS8=2\r]
Apr 12 15:25:03.38: [ 938]: --> [2:OK]
Apr 12 15:25:03.38: [ 938]: <-- [8:ATS7=60\r]
Apr 12 15:25:03.40: [ 938]: --> [2:OK]
Apr 12 15:25:03.40: [ 938]: <-- [6:AT&K4\r]
Apr 12 15:25:03.42: [ 938]: --> [2:OK]
Apr 12 15:25:03.42: [ 938]: <-- [6:AT&D3\r]
Apr 12 15:25:03.45: [ 938]: --> [2:OK]
Apr 12 15:25:03.45: [ 938]: <-- [6:AT&C1\r]
Apr 12 15:25:03.47: [ 938]: --> [2:OK]
Apr 12 15:25:03.47: [ 938]: <-- [12:AT+FCLASS=2\r]
Apr 12 15:25:03.49: [ 938]: --> [2:OK]
Apr 12 15:25:03.49: [ 938]: <-- [10:AT+FTBC=0\r]
Apr 12 15:25:03.51: [ 938]: --> [2:OK]
Apr 12 15:25:03.51: [ 938]: <-- [10:AT+FBOR=0\r]
Apr 12 15:25:03.53: [ 938]: --> [2:OK]
Apr 12 15:25:03.53: [ 938]: <-- [13:AT+FPHCTO=30\r]
Apr 12 15:25:03.56: [ 938]: --> [2:OK]
Apr 12 15:25:03.56: [ 938]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Apr 12 15:25:03.59: [ 938]: --> [2:OK]
Apr 12 15:25:03.59: [ 938]: <-- [5:ATM0\r]
Apr 12 15:25:03.61: [ 938]: --> [2:OK]
Apr 12 15:25:03.61: [ 938]: <-- [12:AT+FCLASS=2\r]
Apr 12 15:25:03.73: [ 938]: --> [2:OK]
Apr 12 15:25:03.73: [ 938]: <-- [10:AT+FTBC=0\r]
Apr 12 15:25:03.85: [ 938]: --> [2:OK]
Apr 12 15:25:03.85: [ 938]: <-- [10:AT+FBOR=0\r]
Apr 12 15:25:03.97: [ 938]: --> [2:OK]
Apr 12 15:25:03.97: [ 938]: <-- [13:AT+FPHCTO=30\r]
Apr 12 15:25:04.09: [ 938]: --> [2:OK]
Apr 12 15:25:04.09: [ 938]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Apr 12 15:25:04.22: [ 938]: --> [2:OK]
Apr 12 15:25:04.22: [ 938]: <-- [26:AT+FLID="EkenbergHylafax"\r]
Apr 12 15:25:04.35: [ 938]: --> [2:OK]
Apr 12 15:25:04.35: [ 938]: DIAL 7043887
Apr 12 15:25:04.35: [ 938]: <-- [12:ATDT7043887\r]
Apr 12 15:25:25.76: [ 938]: --> [5:+FCON]
Apr 12 15:25:27.72: [ 938]: --> [29:+FCSI: " +46317043887"]
Apr 12 15:25:27.72: [ 938]: REMOTE CSI "+46317043887"
Apr 12 15:25:28.26: [ 938]: --> [22:+FDIS: 1,5,0,2,1,0,0,0]
Apr 12 15:25:28.26: [ 938]: --> [2:OK]
Apr 12 15:25:28.26: [ 938]: REMOTE best rate 14400 bit/s
Apr 12 15:25:28.26: [ 938]: REMOTE max page width 1728 pixels in 215 mm
Apr 12 15:25:28.26: [ 938]: REMOTE max unlimited page length
Apr 12 15:25:28.26: [ 938]: REMOTE best vres 7.7 line/mm
Apr 12 15:25:28.26: [ 938]: REMOTE best format 2-D MR
Apr 12 15:25:28.26: [ 938]: REMOTE best 0 ms/scanline
Apr 12 15:25:28.26: [ 938]: USE 14400 bit/s
Apr 12 15:25:28.26: [ 938]: USE 0 ms/scanline
Apr 12 15:25:28.26: [ 938]: SEND file "docq/doc7.ps;30"
Apr 12 15:25:28.26: [ 938]: USE page width 1728 pixels in 215 mm
Apr 12 15:25:28.26: [ 938]: USE unlimited page length
Apr 12 15:25:28.26: [ 938]: USE 3.85 line/mm
Apr 12 15:25:28.26: [ 938]: USE 1-D MR
Apr 12 15:25:28.26: [ 938]: <-- [24:AT+FDIS=0,5,0,2,0,0,0,0\r]
Apr 12 15:25:28.39: [ 938]: --> [2:OK]
Apr 12 15:25:28.39: [ 938]: <-- [7:AT+FDT\r]
Apr 12 15:25:35.85: [ 938]: --> [22:+FDCS: 0,5,0,2,0,0,0,0]
Apr 12 15:25:35.85: [ 938]: --> [7:CONNECT]
Apr 12 15:25:35.85: [ 938]: SEND wait for XON
Apr 12 15:25:35.85: [ 938]: --> [1:]
Apr 12 15:25:35.85: [ 938]: SEND begin page
Apr 12 15:25:35.85: [ 938]: <-- data [1028]
Apr 12 15:25:35.85: [ 938]: <-- data [1028]
Apr 12 15:25:35.85: [ 938]: <-- data [1030]
Apr 12 15:25:35.85: [ 938]: <-- data [1026]
Apr 12 15:25:36.86: [ 938]: <-- data [1027]
Apr 12 15:25:36.86: [ 938]: <-- data [1025]
Apr 12 15:25:36.86: [ 938]: <-- data [1028]
Apr 12 15:25:38.02: [ 938]: <-- data [1030]
Apr 12 15:25:38.60: [ 938]: <-- data [1025]
Apr 12 15:25:39.17: [ 938]: <-- data [478]
Apr 12 15:25:39.17: [ 938]: SENT 9694 bytes of data
Apr 12 15:25:39.17: [ 938]: <-- data [2]
Apr 12 15:25:41.66: [ 938]: SEND end page
Apr 12 15:25:42.49: [ 938]: --> [2:OK]
Apr 12 15:25:42.49: [ 938]: SEND send EOP (no more pages or documents)
Apr 12 15:25:42.49: [ 938]: <-- [9:AT+FET=2\r]
Apr 12 15:25:45.26: [ 938]: --> [8:+FPTS: 1]
Apr 12 15:25:46.83: [ 938]: --> [8:+FHNG: 0]
Apr 12 15:25:46.83: [ 938]: REMOTE HANGUP: Normal and proper end of connection (code 0)
Apr 12 15:25:46.83: [ 938]: SEND recv MCF (message confirmation)
Apr 12 15:25:46.83: [ 938]: SEND FAX (00000006): FROM root@fax.ekenberg.se TO 7043887 (page 1 of 1 sent in 0:18)
Apr 12 15:25:46.83: [ 938]: SEND FAX (00000006): FROM root@fax.ekenberg.se TO 7043887 (docq/doc7.ps;30 sent in 0:18)
Apr 12 15:25:46.83: [ 938]: <-- [5:ATH0\r]
Apr 12 15:25:47.59: [ 938]: --> [2:OK]
Apr 12 15:25:47.59: [ 938]: SESSION END
===== Logfile from trying to send 2 pages to a HP OfficeJet G85 fax machine:
Apr 12 15:32:48.15: [ 1171]: SESSION BEGIN 00000009 46317043887
Apr 12 15:32:48.15: [ 1171]: HylaFAX (tm) Version 4.1.1
Apr 12 15:32:48.15: [ 1171]: SEND FAX: JOB 7 DEST 7043887 COMMID 00000009 DEVICE '/dev/modem'
Apr 12 15:32:48.15: [ 1171]: DELAY 75 ms
Apr 12 15:32:48.23: [ 1171]: DELAY 2600 ms
Apr 12 15:32:50.83: [ 1171]: <-- [4:ATZ\r]
Apr 12 15:32:50.92: [ 1171]: --> [2:OK]
Apr 12 15:32:50.92: [ 1171]: DELAY 3000 ms
Apr 12 15:32:53.92: [ 1171]: <-- [5:ATE0\r]
Apr 12 15:32:53.93: [ 1171]: --> [4:ATE0]
Apr 12 15:32:53.93: [ 1171]: --> [2:OK]
Apr 12 15:32:53.93: [ 1171]: <-- [5:ATV1\r]
Apr 12 15:32:53.95: [ 1171]: --> [2:OK]
Apr 12 15:32:53.95: [ 1171]: <-- [5:ATQ0\r]
Apr 12 15:32:53.97: [ 1171]: --> [2:OK]
Apr 12 15:32:53.97: [ 1171]: <-- [7:ATS0=0\r]
Apr 12 15:32:53.99: [ 1171]: --> [2:OK]
Apr 12 15:32:53.99: [ 1171]: <-- [7:ATS8=2\r]
Apr 12 15:32:54.01: [ 1171]: --> [2:OK]
Apr 12 15:32:54.01: [ 1171]: <-- [8:ATS7=60\r]
Apr 12 15:32:54.03: [ 1171]: --> [2:OK]
Apr 12 15:32:54.03: [ 1171]: <-- [6:AT&K3\r]
Apr 12 15:32:54.05: [ 1171]: --> [2:OK]
Apr 12 15:32:54.05: [ 1171]: <-- [6:AT&D2\r]
Apr 12 15:32:54.07: [ 1171]: --> [2:OK]
Apr 12 15:32:54.07: [ 1171]: <-- [6:AT&C1\r]
Apr 12 15:32:54.09: [ 1171]: --> [2:OK]
Apr 12 15:32:54.09: [ 1171]: <-- [12:AT+FCLASS=1\r]
Apr 12 15:32:54.12: [ 1171]: --> [2:OK]
Apr 12 15:32:54.12: [ 1171]: <-- [5:ATM0\r]
Apr 12 15:32:54.14: [ 1171]: --> [2:OK]
Apr 12 15:32:54.14: [ 1171]: <-- [12:AT+FCLASS=1\r]
Apr 12 15:32:54.27: [ 1171]: --> [2:OK]
Apr 12 15:32:54.27: [ 1171]: DIAL 7043887
Apr 12 15:32:54.27: [ 1171]: <-- [12:ATDT7043887\r]
Apr 12 15:33:15.92: [ 1171]: --> [7:CONNECT]
Apr 12 15:33:16.95: [ 1171]: --> [2:OK]
Apr 12 15:33:16.95: [ 1171]: REMOTE NSF "AD 00 36 20 00 00 00 00 6D"
Apr 12 15:33:16.95: [ 1171]: NSF remote fax equipment: HP
Apr 12 15:33:16.95: [ 1171]: <-- [9:AT+FRH=3\r]
Apr 12 15:33:16.98: [ 1171]: --> [7:CONNECT]
Apr 12 15:33:17.65: [ 1171]: --> [2:OK]
Apr 12 15:33:17.65: [ 1171]: REMOTE CSI "+46317043887"
Apr 12 15:33:17.65: [ 1171]: <-- [9:AT+FRH=3\r]
Apr 12 15:33:17.68: [ 1171]: --> [7:CONNECT]
Apr 12 15:33:18.07: [ 1171]: --> [2:OK]
Apr 12 15:33:18.07: [ 1171]: REMOTE best rate 14400 bit/s
Apr 12 15:33:18.07: [ 1171]: REMOTE max page width 1728 pixels in 215 mm
Apr 12 15:33:18.07: [ 1171]: REMOTE max unlimited page length
Apr 12 15:33:18.07: [ 1171]: REMOTE best vres 7.7 line/mm
Apr 12 15:33:18.07: [ 1171]: REMOTE best format 2-D MMR
Apr 12 15:33:18.07: [ 1171]: REMOTE supports T.30 Annex A, ECM
Apr 12 15:33:18.07: [ 1171]: REMOTE best 0 ms/scanline
Apr 12 15:33:18.07: [ 1171]: USE 14400 bit/s
Apr 12 15:33:18.07: [ 1171]: USE 0 ms/scanline
Apr 12 15:33:18.07: [ 1171]: SEND file "docq/doc10.ps;30"
Apr 12 15:33:18.07: [ 1171]: USE page width 1728 pixels in 215 mm
Apr 12 15:33:18.07: [ 1171]: USE unlimited page length
Apr 12 15:33:18.07: [ 1171]: USE 3.85 line/mm
Apr 12 15:33:18.07: [ 1171]: USE 1-D MR
Apr 12 15:33:18.07: [ 1171]: SEND training at v.17 14400 bit/s
Apr 12 15:33:18.07: [ 1171]: <-- [9:AT+FTH=3\r]
Apr 12 15:33:18.11: [ 1171]: --> [7:CONNECT]
Apr 12 15:33:18.11: [ 1171]: <-- data [23]
Apr 12 15:33:18.11: [ 1171]: <-- data [2]
Apr 12 15:33:19.89: [ 1171]: --> [7:CONNECT]
Apr 12 15:33:19.89: [ 1171]: <-- data [6]
Apr 12 15:33:19.89: [ 1171]: <-- data [2]
Apr 12 15:33:20.35: [ 1171]: --> [2:OK]
Apr 12 15:33:20.35: [ 1171]: <-- [9:AT+FTS=7\r]
Apr 12 15:33:20.46: [ 1171]: --> [2:OK]
Apr 12 15:33:20.46: [ 1171]: <-- [11:AT+FTM=145\r]
Apr 12 15:33:20.50: [ 1171]: --> [7:CONNECT]
Apr 12 15:33:20.50: [ 1171]: <-- data [1024]
Apr 12 15:33:20.50: [ 1171]: <-- data [1024]
Apr 12 15:33:20.50: [ 1171]: <-- data [652]
Apr 12 15:33:20.50: [ 1171]: <-- data [2]
Apr 12 15:33:23.85: [ 1171]: --> [2:OK]
Apr 12 15:33:23.85: [ 1171]: <-- [9:AT+FRH=3\r]
Apr 12 15:33:24.26: [ 1171]: --> [7:CONNECT]
Apr 12 15:33:25.16: [ 1171]: --> [2:OK]
Apr 12 15:33:25.16: [ 1171]: TRAINING succeeded
Apr 12 15:33:25.16: [ 1171]: DELAY 75 ms
Apr 12 15:33:25.24: [ 1171]: <-- [11:AT+FTM=146\r]
Apr 12 15:33:25.28: [ 1171]: --> [7:CONNECT]
Apr 12 15:33:25.28: [ 1171]: SEND begin page
Apr 12 15:33:25.28: [ 1171]: <-- data [1029]
Apr 12 15:33:25.28: [ 1171]: <-- data [1028]
Apr 12 15:33:25.28: [ 1171]: <-- data [1028]
Apr 12 15:33:25.28: [ 1171]: <-- data [1025]
Apr 12 15:33:25.28: [ 1171]: <-- data [1027]
Apr 12 15:33:25.96: [ 1171]: <-- data [1030]
Apr 12 15:33:26.46: [ 1171]: <-- data [1030]
Apr 12 15:33:27.46: [ 1171]: <-- data [1025]
Apr 12 15:33:27.95: [ 1171]: <-- data [1028]
Apr 12 15:33:28.46: [ 1171]: <-- data [1028]
Apr 12 15:33:29.49: [ 1171]: <-- data [1032]
Apr 12 15:33:29.99: [ 1171]: <-- data [1024]
Apr 12 15:33:30.49: [ 1171]: <-- data [1027]
Apr 12 15:33:30.99: [ 1171]: <-- data [1029]
Apr 12 15:33:32.03: [ 1171]: <-- data [1030]
Apr 12 15:33:32.53: [ 1171]: <-- data [1026]
Apr 12 15:33:33.04: [ 1171]: <-- data [1026]
Apr 12 15:33:33.54: [ 1171]: <-- data [1028]
Apr 12 15:33:34.54: [ 1171]: <-- data [1027]
Apr 12 15:33:35.05: [ 1171]: <-- data [1030]
Apr 12 15:33:35.55: [ 1171]: <-- data [1028]
Apr 12 15:33:36.55: [ 1171]: <-- data [1031]
Apr 12 15:33:37.05: [ 1171]: <-- data [998]
Apr 12 15:33:37.57: [ 1171]: SENT 23525 bytes of data
Apr 12 15:33:37.57: [ 1171]: SEND 1D RTC
Apr 12 15:33:37.57: [ 1171]: <-- data [29]
Apr 12 15:33:37.57: [ 1171]: <-- data [2]
Apr 12 15:33:37.57: [ 1171]: SEND end page
Apr 12 15:33:40.46: [ 1171]: --> [2:OK]
Apr 12 15:33:40.46: [ 1171]: <-- [9:AT+FTS=7\r]
Apr 12 15:33:40.55: [ 1171]: --> [2:OK]
Apr 12 15:33:40.55: [ 1171]: SEND send MPS (more pages, same document)
Apr 12 15:33:40.55: [ 1171]: <-- [9:AT+FTH=3\r]
Apr 12 15:33:40.59: [ 1171]: --> [7:CONNECT]
Apr 12 15:33:40.59: [ 1171]: <-- data [3]
Apr 12 15:33:40.59: [ 1171]: <-- data [2]
Apr 12 15:33:41.89: [ 1171]: --> [2:OK]
Apr 12 15:33:41.89: [ 1171]: <-- [9:AT+FRH=3\r]
Apr 12 15:33:44.99: [ 1171]: --> [0:]
Apr 12 15:33:44.99: [ 1171]: MODEM <Empty line>
Apr 12 15:33:44.99: [ 1171]: <-- data [1]
Apr 12 15:33:45.06: [ 1171]: --> [2:OK]
Apr 12 15:33:45.06: [ 1171]: SEND send MPS (more pages, same document)
Apr 12 15:33:45.06: [ 1171]: <-- [9:AT+FTH=3\r]
Apr 12 15:33:45.10: [ 1171]: --> [7:CONNECT]
Apr 12 15:33:45.10: [ 1171]: <-- data [3]
Apr 12 15:33:45.10: [ 1171]: <-- data [2]
Apr 12 15:33:46.43: [ 1171]: --> [2:OK]
Apr 12 15:33:46.43: [ 1171]: <-- [9:AT+FRH=3\r]
Apr 12 15:33:49.53: [ 1171]: --> [0:]
Apr 12 15:33:49.53: [ 1171]: MODEM <Empty line>
Apr 12 15:33:49.53: [ 1171]: <-- data [1]
Apr 12 15:33:49.60: [ 1171]: --> [2:OK]
Apr 12 15:33:49.60: [ 1171]: SEND send MPS (more pages, same document)
Apr 12 15:33:49.60: [ 1171]: <-- [9:AT+FTH=3\r]
Apr 12 15:33:49.64: [ 1171]: --> [7:CONNECT]
Apr 12 15:33:49.64: [ 1171]: <-- data [3]
Apr 12 15:33:49.64: [ 1171]: <-- data [2]
Apr 12 15:33:50.96: [ 1171]: --> [2:OK]
Apr 12 15:33:50.96: [ 1171]: <-- [9:AT+FRH=3\r]
Apr 12 15:33:54.06: [ 1171]: --> [0:]
Apr 12 15:33:54.06: [ 1171]: MODEM <Empty line>
Apr 12 15:33:54.06: [ 1171]: <-- data [1]
Apr 12 15:33:54.13: [ 1171]: --> [2:OK]
Apr 12 15:33:54.13: [ 1171]: No response to MPS or EOP repeated 3 tries
Apr 12 15:33:54.13: [ 1171]: <-- [9:AT+FTH=3\r]
Apr 12 15:33:54.17: [ 1171]: --> [7:CONNECT]
Apr 12 15:33:54.17: [ 1171]: <-- data [3]
Apr 12 15:33:54.17: [ 1171]: <-- data [2]
Apr 12 15:33:55.47: [ 1171]: --> [2:OK]
Apr 12 15:33:55.47: [ 1171]: <-- [5:ATH0\r]
Apr 12 15:33:56.35: [ 1171]: --> [2:OK]
Apr 12 15:33:56.35: [ 1171]: SESSION END
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
