Hylafax Mailing List Archives

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

[hylafax-users] 3com sportser and hyla



Hi everyone,
    As suggested by Lee Howard i changed my configuration of hyla to class one , all ok about receving !!! Thank you very much.
 
Sending of fax is very difficult now, the most common error is no carrier detected.
 
here is my conf file, anyone who has any suggestion ???
 
 

# Generic Class 1 modem configuration.

# BEGIN-SERVER

CountryCode: 39 

LongDistancePrefix: 0

InternationalPrefix: 00

AreaCode: 051

DialStringRules: etc/dialrules

FAXNumber: +39051xxxxxxx

LocalIdentifier: "xxxxxxx" 

ServerTracing: 1 

SessionTracing: 11 

RecvFileMode: 0666 

LogFileMode: 0600 

DeviceMode: 0600 

#QualifyTSI: etc/tsi # accept facsimile from anyone

SpeakerVolume: off

RingsBeforeAnswer: 2 

TagLineFont: etc/lutRS18.pcf 

TagLineFormat: "Da %%l|%c|Pagina %%P di %%T"

#MaxBadCalls: 5 

PostScriptTimeout: 300 

MaxSendPages: 50 

MaxRecvPages: 50 

#ContCoverPage: etc/cover.templ # enable continuation cover pages

#DestControls: etc/destcontrols # destination-specific controls

#MaxConcurrentJobs: 1 # serialize jobs to the same dest

#TimeOfDay: "Any" # outbound jobs any day, any time

# END-SERVER

#

# Modem-related stuff: should reflect modem command interface

# and hardware connection/cabling (e.g. flow control).

#

ModemType: Class1 # use this to supply a hint

ModemRate: 19200 # rate for DCE-DTE communication

ModemFlowControl: rtscts # XON/XOFF flow control assumed

#

ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem

ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier

GettyArgs: "-h %l dx_%s" # modem must auto-detect fax/data

ModemDialCmd: ATS7=100DT%s@ # T for tone dialing, @ for silence

#

#ModemNoFlowCmd AT&H0&I0&R1

#ModemHardFlowCmd AT&H1&I0&R2

#ModemSoftFlowCmd AT&H2&I2&R1

ModemResetCmds: "" # stuff to do when modem is reset

ModemAnswerCmd: ATA # use this to answer phone

ModemNoFlowCmd: AT&K # disable flow control cmd

ModemHardFlowCmd: AT&K3 # hardware flow control cmd

ModemSoftFlowCmd: AT&K4 # software flow control cmd

ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer

#

# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.

# Note that we both turn the speaker on/off and set volume.

#

ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"

ModemEchoOffCmd: ATE0 # disable command echo

ModemVerboseResultsCmd: ATV1 # enable verbose command results

ModemResultCodesCmd: ATQ0 # enable result codes

ModemOnHookCmd: ATH0 # place phone on hook (hangup)

ModemSoftResetCmd: ATZ # do soft reset of modem

ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier

#ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds

#ModemRecvFillOrder: LSB2MSB # bit order of received facsimile

#ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit

#

Class1Cmd: AT+FCLASS=1 # command to enter class 1

Class1TCFResponseDelay: 75 # 75ms delay between recv TCF & response

Class1SendPPMDelay: 75 # 75ms delay before sending PPM

Class1SendTCFDelay: 75 # 75ms delay between sending DCS & TCF

Class1SwitchingDelay: 150 # 150ms delay in switching transmission direction

Class1TrainingRecovery: 1500 # 1.5sec delay after training failure

Class1RecvAbortOK: 200 # wait 200ms for abort response

Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames

Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames

Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero

Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration

  
 
 
 
Massimo Donato
 
e-mail tecnico@adcom.it


Home
Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services