|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] RSRPEC error/got DCN
This is the first time I have run across this error in the months of
using hylafax, I have the most current version which is running on RH
7.0. Any suggestions in keeping this error from occurring in the future?
Also, it made three attempts to send this document, how can I get it to
try more than three times when hylafax registers an error?
Any help is appreciated.
RSRPEC error/got DCN; Giving up after 3 attempts to send same page
---- Transcript of session follows ----
Mar 05 15:33:11.20: [ 6850]: SESSION BEGIN 00000089 12147581550
Mar 05 15:33:11.20: [ 6850]: HylaFAX (tm) Version 4.1
Mar 05 15:33:11.20: [ 6850]: SEND FAX: JOB 188 DEST 12147581550 COMMID
00000089
Mar 05 15:33:11.20: [ 6850]: DEVICE '/dev/ttyS0'
Mar 05 15:33:11.20: [ 6850]: MODEM set DTR OFF
Mar 05 15:33:11.20: [ 6850]: DELAY 75 ms
Mar 05 15:33:11.28: [ 6850]: MODEM set DTR ON
Mar 05 15:33:11.28: [ 6850]: DELAY 2600 ms
Mar 05 15:33:13.88: [ 6850]: MODEM set baud rate: 19200 baud, input
flow
RTS/CTS, output flow RTS/CTS
Mar 05 15:33:13.88: [ 6850]: MODEM flush i/o
Mar 05 15:33:13.88: [ 6850]: <-- [4:ATZ\r]
Mar 05 15:33:14.85: [ 6850]: --> [2:OK]
Mar 05 15:33:14.85: [ 6850]: <-- [5:ATE0\r]
Mar 05 15:33:14.86: [ 6850]: --> [4:ATE0]
Mar 05 15:33:14.87: [ 6850]: --> [2:OK]
Mar 05 15:33:14.87: [ 6850]: <-- [5:ATV1\r]
Mar 05 15:33:14.88: [ 6850]: --> [2:OK]
Mar 05 15:33:14.88: [ 6850]: <-- [5:ATQ0\r]
Mar 05 15:33:14.89: [ 6850]: --> [2:OK]
Mar 05 15:33:14.89: [ 6850]: <-- [7:ATS0=0\r]
Mar 05 15:33:14.91: [ 6850]: --> [2:OK]
Mar 05 15:33:14.91: [ 6850]: <-- [7:ATS8=2\r]
Mar 05 15:33:14.93: [ 6850]: --> [2:OK]
Mar 05 15:33:14.93: [ 6850]: <-- [8:ATS7=60\r]
Mar 05 15:33:14.95: [ 6850]: --> [2:OK]
Mar 05 15:33:14.95: [ 6850]: <-- [12:AT+FCLASS=1\r]
Mar 05 15:33:14.97: [ 6850]: --> [2:OK]
Mar 05 15:33:14.97: [ 6850]: <-- [5:ATM0\r]
Mar 05 15:33:14.98: [ 6850]: --> [2:OK]
Mar 05 15:33:14.98: [ 6850]: STATE CHANGE: RUNNING -> SENDING
Mar 05 15:33:14.98: [ 6850]: MODEM input buffering enabled
Mar 05 15:33:14.98: [ 6850]: <-- [12:AT+FCLASS=1\r]
Mar 05 15:33:15.10: [ 6850]: --> [2:OK]
Mar 05 15:33:15.12: [ 6850]: DIAL 12147581550
Mar 05 15:33:15.12: [ 6850]: <-- [16:ATDT12147581550\r]
Mar 05 15:33:30.34: [ 6850]: --> [7:CONNECT]
Mar 05 15:33:30.34: [ 6850]: MODEM input buffering disabled
Mar 05 15:33:32.28: [ 6850]: --> HDLC<36:FF C0 04 00 00 90 00 10 B6 84
E2 1A A8
0A FF FF FF FF FF FF FF 80 96 40 50 08 80 41 80 0C 00 00 00 96 6B 25>
Mar 05 15:33:32.28: [ 6850]: --> [2:OK]
Mar 05 15:33:32.28: [ 6850]: REMOTE NSF "00 00 09 00 08 6D 21 47 58 15
50 FF FF
FF FF FF FF FF 01 69 02 0A 10 01 82 01 30 00 00 00 69 D6"
Mar 05 15:33:32.28: [ 6850]: NSF remote fax equipment: Xerox
Mar 05 15:33:32.28: [ 6850]: NSF remote station ID: "XG!m"
Mar 05 15:33:32.28: [ 6850]: <-- [9:AT+FRH=3\r]
Mar 05 15:33:32.30: [ 6850]: --> [7:CONNECT]
Mar 05 15:33:33.00: [ 6850]: --> HDLC<25:FF C0 02 0C AC AC 8C 1C AC EC
2C 8C 4C
04 04 04 04 04 04 04 04 04 04 48 79>
Mar 05 15:33:33.01: [ 6850]: --> [2:OK]
Mar 05 15:33:33.01: [ 6850]: REMOTE CSI "2147581550"
Mar 05 15:33:33.01: [ 6850]: <-- [9:AT+FRH=3\r]
Mar 05 15:33:33.03: [ 6850]: --> [7:CONNECT]
Mar 05 15:33:33.37: [ 6850]: --> HDLC<12:FF C8 01 00 77 19 23 01 EB C0
52 D8>
Mar 05 15:33:33.38: [ 6850]: --> [2:OK]
Mar 05 15:33:33.38: [ 6850]: REMOTE best rate 14400 bit/s
Mar 05 15:33:33.38: [ 6850]: REMOTE max page width 1728 pixels in 215
mm
Mar 05 15:33:33.38: [ 6850]: REMOTE max unlimited page length
Mar 05 15:33:33.38: [ 6850]: REMOTE best vres 7.7 line/mm
Mar 05 15:33:33.38: [ 6850]: REMOTE best format 2-D MMR
Mar 05 15:33:33.38: [ 6850]: REMOTE supports T.30 Annex A, ECM
Mar 05 15:33:33.38: [ 6850]: REMOTE best 5 ms/scanline
Mar 05 15:33:33.38: [ 6850]: USE 14400 bit/s
Mar 05 15:33:33.38: [ 6850]: USE 5 ms/scanline
Mar 05 15:33:33.38: [ 6850]: SEND file "docq/doc284.ps;01"
Mar 05 15:33:33.41: [ 6850]: USE page width 1728 pixels in 215 mm
Mar 05 15:33:33.42: [ 6850]: USE unlimited page length
Mar 05 15:33:33.42: [ 6850]: USE 7.7 line/mm
Mar 05 15:33:33.42: [ 6850]: USE 1-D MR
Mar 05 15:33:33.42: [ 6850]: SEND training at v.17 14400 bit/s
Mar 05 15:33:33.42: [ 6850]: <-- [9:AT+FTH=3\r]
Mar 05 15:33:34.36: [ 6850]: --> [7:CONNECT]
Mar 05 15:33:34.36: [ 6850]: <-- HDLC<23:FF C0 C2 AE CE 76 F6 C2 04 9E
A6 76 4E
F6 2E 2E 82 04 2E CE 4E 96 62>
Mar 05 15:33:34.39: [ 6850]: --> [7:CONNECT]
Mar 05 15:33:34.39: [ 6850]: <-- HDLC<6:FF C8 C1 00 46 18>
Mar 05 15:33:35.48: [ 6850]: --> [2:OK]
Mar 05 15:33:35.48: [ 6850]: <-- [9:AT+FTS=7\r]
Mar 05 15:33:35.57: [ 6850]: --> [2:OK]
Mar 05 15:33:35.57: [ 6850]: <-- [11:AT+FTM=145\r]
Mar 05 15:33:35.59: [ 6850]: --> [7:CONNECT]
Mar 05 15:33:38.72: [ 6850]: --> [2:OK]
Mar 05 15:33:38.72: [ 6850]: <-- [9:AT+FRH=3\r]
Mar 05 15:33:39.43: [ 6850]: --> [7:CONNECT]
Mar 05 15:33:40.60: [ 6850]: --> HDLC<5:FF C8 5F C8 E7>
Mar 05 15:33:40.61: [ 6850]: --> [2:OK]
Mar 05 15:33:40.61: [ 6850]: TRAINING failed
Mar 05 15:33:40.61: [ 6850]: SEND: RSRPEC error/got DCN; Giving up
after 3
attempts to send same page "docq/doc284.ps;01", dirnum 0
Mar 05 15:33:40.61: [ 6850]: <-- [9:AT+FTH=3\r]
Mar 05 15:33:41.55: [ 6850]: --> [7:CONNECT]
Mar 05 15:33:41.55: [ 6850]: <-- HDLC<3:FF C8 DF>
Mar 05 15:33:41.87: [ 6850]: --> [2:OK]
Mar 05 15:33:41.87: [ 6850]: MODEM input buffering enabled
Mar 05 15:33:41.87: [ 6850]: <-- [5:ATH0\r]
Mar 05 15:33:43.27: [ 6850]: --> [2:OK]
Mar 05 15:33:43.27: [ 6850]: MODEM set DTR OFF
Mar 05 15:33:43.27: [ 6850]: STATE CHANGE: SENDING -> MODEMWAIT
(timeout 5)
Mar 05 15:33:43.27: [ 6850]: SESSION END
____________________ HylaFAX(tm) Users Mailing List _______________________
To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
