|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] 3com faxmodem or trust 28.8
Hi,
I'm just looking to best tune my system because i think 5/7 % of the fax
end in an error state, i think that some small config variation could help
here you are two error log one for receive end one for send.
fax numbers subst by xxx
thanks a lot and sorry for my english
Your facsimile job to xxxxxxxxxx was not sent because:
RSPREC error/got DCN
The job will be retried at 11:25.
---- Transcript of session follows ----
Mar 01 11:23:05.75: [31926]: SESSION BEGIN 00000780 39xxxxxxxxxxx
Mar 01 11:23:05.75: [31926]: HylaFAX (tm) Version 4.1
Mar 01 11:23:05.75: [31926]: SEND FAX: JOB 83 DEST 0xxxxxxxxxx COMMID
00000780
Mar 01 11:23:05.75: [31926]: DEVICE '/dev/ttyS0'
Mar 01 11:23:05.75: [31926]: DELAY 75 ms
Mar 01 11:23:05.83: [31926]: DELAY 2600 ms
Mar 01 11:23:08.43: [31926]: <-- [4:ATZ\r]
Mar 01 11:23:08.56: [31926]: --> [2:OK]
Mar 01 11:23:08.56: [31926]: <-- [5:ATE0\r]
Mar 01 11:23:08.69: [31926]: --> [4:ATE0]
Mar 01 11:23:08.69: [31926]: --> [2:OK]
Mar 01 11:23:08.69: [31926]: <-- [5:ATV1\r]
Mar 01 11:23:08.82: [31926]: --> [2:OK]
Mar 01 11:23:08.82: [31926]: <-- [7:ATQ0X4\r]
Mar 01 11:23:08.95: [31926]: --> [2:OK]
Mar 01 11:23:08.95: [31926]: <-- [7:ATS0=0\r]
Mar 01 11:23:09.08: [31926]: --> [2:OK]
Mar 01 11:23:09.08: [31926]: <-- [7:ATS8=2\r]
Mar 01 11:23:09.21: [31926]: --> [2:OK]
Mar 01 11:23:09.21: [31926]: <-- [8:ATS7=60\r]
Mar 01 11:23:09.34: [31926]: --> [2:OK]
Mar 01 11:23:09.34: [31926]: <-- [12:AT&H1&I0&R2\r]
Mar 01 11:23:09.48: [31926]: --> [2:OK]
Mar 01 11:23:09.48: [31926]: <-- [11:ATS13=1&D2\r]
Mar 01 11:23:09.62: [31926]: --> [2:OK]
Mar 01 11:23:09.62: [31926]: <-- [6:AT&C1\r]
Mar 01 11:23:09.75: [31926]: --> [2:OK]
Mar 01 11:23:09.75: [31926]: <-- [14:AT+FCLASS=2.0\r]
Mar 01 11:23:09.89: [31926]: --> [2:OK]
Mar 01 11:23:09.89: [31926]: <-- [9:AT+FLO=2\r]
Mar 01 11:23:10.03: [31926]: --> [2:OK]
Mar 01 11:23:10.03: [31926]: <-- [9:AT+FPP=0\r]
Mar 01 11:23:10.17: [31926]: --> [2:OK]
Mar 01 11:23:10.17: [31926]: <-- [9:AT+FBO=0\r]
Mar 01 11:23:10.31: [31926]: --> [2:OK]
Mar 01 11:23:10.31: [31926]: <-- [10:AT+FCT=30\r]
Mar 01 11:23:10.45: [31926]: --> [2:OK]
Mar 01 11:23:10.45: [31926]: <-- [15:AT+FNR=1,1,1,0\r]
Mar 01 11:23:10.59: [31926]: --> [2:OK]
Mar 01 11:23:10.59: [31926]: <-- [9:AT+FIE=0\r]
Mar 01 11:23:10.73: [31926]: --> [2:OK]
Mar 01 11:23:10.73: [31926]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Mar 01 11:23:10.87: [31926]: --> [2:OK]
Mar 01 11:23:10.87: [31926]: <-- [5:ATM0\r]
Mar 01 11:23:11.00: [31926]: --> [2:OK]
Mar 01 11:23:11.00: [31926]: <-- [14:AT+FCLASS=2.0\r]
Mar 01 11:23:11.24: [31926]: --> [2:OK]
Mar 01 11:23:11.24: [31926]: <-- [9:AT+FLO=2\r]
Mar 01 11:23:11.48: [31926]: --> [2:OK]
Mar 01 11:23:11.48: [31926]: <-- [9:AT+FPP=0\r]
Mar 01 11:23:11.72: [31926]: --> [2:OK]
Mar 01 11:23:11.72: [31926]: <-- [9:AT+FBO=0\r]
Mar 01 11:23:11.96: [31926]: --> [2:OK]
Mar 01 11:23:11.96: [31926]: <-- [10:AT+FCT=30\r]
Mar 01 11:23:12.20: [31926]: --> [2:OK]
Mar 01 11:23:12.20: [31926]: <-- [15:AT+FNR=1,1,1,0\r]
Mar 01 11:23:12.44: [31926]: --> [2:OK]
Mar 01 11:23:12.44: [31926]: <-- [9:AT+FIE=0\r]
Mar 01 11:23:12.68: [31926]: --> [2:OK]
Mar 01 11:23:12.68: [31926]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Mar 01 11:23:12.92: [31926]: --> [2:OK]
Mar 01 11:23:12.92: [31926]: <-- [19:AT+FLI="Adcom Srl"\r]
Mar 01 11:23:13.16: [31926]: --> [2:OK]
Mar 01 11:23:13.16: [31926]: DIAL 0xxxxxxxxxxxxx
Mar 01 11:23:13.16: [31926]: <-- [15:ATDT0xxxxxxxxxxxxxx\r]
Mar 01 11:23:30.19: [31926]: --> [4:+FCO]
Mar 01 11:23:33.55: [31926]: --> [27:+FCI:" 0039 0522 625525"]
Mar 01 11:23:33.55: [31926]: REMOTE CSI "0039 0522 625525"
Mar 01 11:23:33.55: [31926]: --> [20:+FIS:1,5,0,2,1,0,0,2]
Mar 01 11:23:33.55: [31926]: --> [2:OK]
Mar 01 11:23:33.55: [31926]: REMOTE best rate 14400 bit/s
Mar 01 11:23:33.55: [31926]: REMOTE max page width 1728 pixels in 215 mm
Mar 01 11:23:33.55: [31926]: REMOTE max unlimited page length
Mar 01 11:23:33.55: [31926]: REMOTE best vres 7.7 line/mm
Mar 01 11:23:33.55: [31926]: REMOTE best format 2-D MR
Mar 01 11:23:33.55: [31926]: REMOTE best 10 ms, 5 ms/scanline
Mar 01 11:23:33.55: [31926]: USE 14400 bit/s
Mar 01 11:23:33.55: [31926]: USE 10 ms, 5 ms/scanline
Mar 01 11:23:33.55: [31926]: SEND file "docq/doc83.ps;00"
Mar 01 11:23:33.55: [31926]: USE page width 1728 pixels in 215 mm
Mar 01 11:23:33.55: [31926]: USE unlimited page length
Mar 01 11:23:33.55: [31926]: USE 3.85 line/mm
Mar 01 11:23:33.55: [31926]: USE 1-D MR
Mar 01 11:23:33.55: [31926]: <-- [23:AT+FIS=0,5,0,2,0,0,0,2\r]
Mar 01 11:23:33.79: [31926]: --> [2:OK]
Mar 01 11:23:33.79: [31926]: <-- [7:AT+FDT\r]
Mar 01 11:23:34.06: [31926]: --> [20:+FCS:0,5,0,2,0,0,0,2]
Mar 01 11:23:40.87: [31926]: --> [7:CONNECT]
Mar 01 11:23:40.87: [31926]: SEND begin page
Mar 01 11:23:59.23: [31926]: SENT 32939 bytes of data
Mar 01 11:23:59.23: [31926]: SEND 1D RTC
Mar 01 11:23:59.23: [31926]: SEND end page
Mar 01 11:23:59.23: [31926]: SEND send EOP (no more pages or documents)
Mar 01 11:24:12.37: [31926]: --> [7:+FHS:51]
Mar 01 11:24:12.37: [31926]: REMOTE HANGUP: RSPREC error/got DCN (code 51)
Mar 01 11:24:12.37: [31926]: <-- [5:ATH0\r]
Mar 01 11:24:12.49: [31926]: --> [2:OK]
Mar 01 11:24:12.49: [31926]: SESSION END
here is another:
recvq/fax00411.tif:
Could not open recvq/fax00411.tif; either not TIFF or corrupted.
The full document was not received because:
RSPREC invalid response received
---- Transcript of session follows ----
Mar 01 13:30:57.16: [20716]: SESSION BEGIN 00000786 39051352680
Mar 01 13:30:57.16: [20716]: <-- [4:ATA\r]
Mar 01 13:31:05.91: [20716]: --> [4:+FCO]
Mar 01 13:31:05.91: [20716]: ANSWER: FAX CONNECTION
Mar 01 13:31:05.91: [20716]: RECV FAX: begin
Mar 01 13:31:07.93: [20716]: --> [27:+FTI:" +39 xxxxxxxxx"]
Mar 01 13:31:07.93: [20716]: REMOTE TSI "+39 xxxxxxxxxxx"
Mar 01 13:31:07.93: [20716]: --> [20:+FCS:1,5,0,2,0,0,0,1]
Mar 01 13:31:07.93: [20716]: REMOTE wants 14400 bit/s
Mar 01 13:31:07.93: [20716]: REMOTE wants page width 1728 pixels in 215 mm
Mar 01 13:31:07.93: [20716]: REMOTE wants unlimited page length
Mar 01 13:31:07.93: [20716]: REMOTE wants 7.7 line/mm
Mar 01 13:31:07.93: [20716]: REMOTE wants 1-D MR
Mar 01 13:31:07.93: [20716]: --> [2:OK]
Mar 01 13:31:07.93: [20716]: <-- [7:AT+FDR\r]
Mar 01 13:31:13.03: [20716]: --> [7:CONNECT]
Mar 01 13:31:13.03: [20716]: RECV: begin page
Mar 01 13:31:13.03: [20716]: RECV: send trigger 022
Mar 01 13:31:13.03: [20716]: <-- data [1]
Mar 01 13:31:35.02: [20716]: RECV: 1248 total lines, 0 bad lines, 0
consecutive bad lines
Mar 01 13:31:35.13: [20716]: --> [17:+FPS:1,1249,0,0,0]
Mar 01 13:31:44.48: [20716]: --> [7:+FHS:A1]
Mar 01 13:31:44.48: [20716]: REMOTE HANGUP: RSPREC invalid response received
(code A1)
Mar 01 13:31:44.61: [20716]: --> [2:OK]
Mar 01 13:31:44.61: [20716]: RECV FAX (00000786): recvq/fax00411.tif from
+39 xxxxxxxxxx, route to <unspecified>, 0 pages in 0:39
Mar 01 13:31:44.61: [20716]: RECV FAX: RSPREC invalid response received
Mar 01 13:31:44.61: [20716]: RECV FAX (00000786): session with +39
xxxxxxxxxxxxx terminated abnormally: RSPREC invalid response received
Mar 01 13:31:44.61: [20716]: RECV FAX: bin/faxrcvd "recvq/fax00411.tif"
"ttyS0" "00000786" "RSPREC invalid response received"
----- Original Message -----
From: "Lee Howard" <faxguy@deanox.com>
To: "Massimo Donato" <tecnico@adcom.it>
Cc: <hylafax-users@hylafax.org>
Sent: Friday, March 01, 2002 5:36 PM
Subject: Re: [hylafax-users] 3com faxmodem or trust 28.8
> On 2002.03.01 07:41 Massimo Donato wrote:
> > Hi hylafax-users@hylafax.org,
> > does anyone have a well working config file for one of this two
> > modems
> > or can give me some advice on a modem that works very well vith others.
> > the 3com faxmodem i use now has some roblems with remote faxes like EOP
> > or
> > other errors.
>
> Running in Class 1 with HylaFAX 4.1.1 you shouldn't be getting many (if
> any) consistent "problems with remote faxes like EOP or other errors" that
> would warrant changing modems. Post the session log and let's try to
> diagnose the real problem.
>
> Lee.
>
> ____________________ HylaFAX(tm) Users Mailing List
_______________________
> To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org <
/dev/null
>
____________________ HylaFAX(tm) Users Mailing List _______________________
To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
