|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Unspecified Transmit Phase C
I have a "U.S. Robotics 56K FAX EXT Rev. 11.13.14" modem that I have
connected to a machine (FreeBSD 4.1) using hylafax-4.1.b2. I am trying
to send faxes but seem to be getting "Unspecified Transmit Phase C error"
when sending to 60% of sites. The modem is set to Class 1 as Class 2.0 did
not seem to work.
Any ideas on what the problem is and how to fix it??
----------------------------------------------------------------------------
Your facsimile job (facsimile job 69) to 32912496 failed because:
Unspecified Transmit Phase C error; Giving up after 3 attempts to send same page
---- Transcript of session follows ----
Jan 17 14:28:07.04: [44376]: SESSION BEGIN 00000138 141532912496
Jan 17 14:28:07.04: [44376]: SEND FAX: JOB 69 DEST 32912496 COMMID 00000138
Jan 17 14:28:07.04: [44376]: DELAY 2600 ms
Jan 17 14:28:12.65: [44376]: DELAY 100 ms
Jan 17 14:28:12.76: [44376]: <-- [17:ATE0V1Q0X3S0=0H0\r]
Jan 17 14:28:12.91: [44376]: --> [2:OK]
Jan 17 14:28:12.91: [44376]: DELAY 100 ms
Jan 17 14:28:13.02: [44376]: <-- [12:ATS8=2S7=60\r]
Jan 17 14:28:13.16: [44376]: --> [2:OK]
Jan 17 14:28:13.16: [44376]: DELAY 100 ms
Jan 17 14:28:13.27: [44376]: <-- [12:AT+FCLASS=1\r]
Jan 17 14:28:13.41: [44376]: --> [2:OK]
Jan 17 14:28:13.41: [44376]: DELAY 100 ms
Jan 17 14:28:13.52: [44376]: <-- [5:ATM0\r]
Jan 17 14:28:13.66: [44376]: --> [2:OK]
Jan 17 14:28:13.67: [44376]: DELAY 100 ms
Jan 17 14:28:13.78: [44376]: <-- [12:AT+FCLASS=1\r]
Jan 17 14:28:14.02: [44376]: --> [2:OK]
Jan 17 14:28:14.02: [44376]: DIAL 32912496
Jan 17 14:28:14.02: [44376]: DELAY 100 ms
Jan 17 14:28:14.13: [44376]: <-- [13:ATDT32912496\r]
Jan 17 14:28:26.24: [44376]: --> [7:CONNECT]
Jan 17 14:28:27.16: [44376]: --> [2:OK]
Jan 17 14:28:27.16: [44376]: DELAY 100 ms
Jan 17 14:28:27.27: [44376]: <-- [9:AT+FRH=3\r]
Jan 17 14:28:27.28: [44376]: --> [7:CONNECT]
Jan 17 14:28:27.90: [44376]: --> [2:OK]
Jan 17 14:28:27.90: [44376]: REMOTE CSI "03 32912496"
Jan 17 14:28:27.90: [44376]: DELAY 100 ms
Jan 17 14:28:28.01: [44376]: <-- [9:AT+FRH=3\r]
Jan 17 14:28:28.02: [44376]: --> [7:CONNECT]
Jan 17 14:28:28.25: [44376]: --> [2:OK]
Jan 17 14:28:28.25: [44376]: REMOTE best rate 9600 bit/s
Jan 17 14:28:28.25: [44376]: REMOTE max page width 1728 pixels in 215 mm
Jan 17 14:28:28.25: [44376]: REMOTE max unlimited page length
Jan 17 14:28:28.25: [44376]: REMOTE best vres 7.7 line/mm
Jan 17 14:28:28.25: [44376]: REMOTE best format 2-D MR
Jan 17 14:28:28.25: [44376]: REMOTE best 20 ms, 10 ms/scanline
Jan 17 14:28:28.25: [44376]: USE 9600 bit/s
Jan 17 14:28:28.25: [44376]: USE 20 ms, 10 ms/scanline
Jan 17 14:28:28.25: [44376]: SEND file "docq/doc72.ps;00"
Jan 17 14:28:28.25: [44376]: USE page width 1728 pixels in 215 mm
Jan 17 14:28:28.25: [44376]: USE unlimited page length
Jan 17 14:28:28.25: [44376]: USE 3.85 line/mm
Jan 17 14:28:28.25: [44376]: USE 1-D MR
Jan 17 14:28:28.25: [44376]: SEND training at v.29 9600 bit/s
Jan 17 14:28:28.25: [44376]: DELAY 100 ms
Jan 17 14:28:28.36: [44376]: <-- [9:AT+FTH=3\r]
Jan 17 14:28:28.55: [44376]: --> [7:CONNECT]
Jan 17 14:28:28.58: [44376]: --> [7:CONNECT]
Jan 17 14:28:30.53: [44376]: --> [2:OK]
Jan 17 14:28:30.53: [44376]: DELAY 75 ms
Jan 17 14:28:30.61: [44376]: DELAY 100 ms
Jan 17 14:28:30.72: [44376]: <-- [10:AT+FTM=96\r]
Jan 17 14:28:31.03: [44376]: --> [7:CONNECT]
Jan 17 14:28:32.57: [44376]: --> [2:OK]
Jan 17 14:28:32.57: [44376]: DELAY 100 ms
Jan 17 14:28:32.67: [44376]: <-- [9:AT+FRH=3\r]
Jan 17 14:28:33.34: [44376]: --> [7:CONNECT]
Jan 17 14:28:34.29: [44376]: --> [2:OK]
Jan 17 14:28:34.29: [44376]: TRAINING succeeded
Jan 17 14:28:34.29: [44376]: DELAY 100 ms
Jan 17 14:28:34.40: [44376]: <-- [10:AT+FTM=96\r]
Jan 17 14:28:34.74: [44376]: --> [7:CONNECT]
Jan 17 14:28:34.74: [44376]: SEND begin page
Jan 17 14:28:48.15: [44376]: SENT 27485 bytes of data
Jan 17 14:28:57.73: [44376]: SENT 17689 bytes of data
Jan 17 14:28:57.73: [44376]: SEND 1D RTC
Jan 17 14:28:57.73: [44376]: SEND end page
Jan 17 14:30:17.74: [44376]: SEND: Unspecified Transmit Phase C error; Giving up after 3 attempts to send same page "docq/doc72.ps;00", dirnum 0
Jan 17 14:30:17.74: [44376]: DELAY 100 ms
Jan 17 14:30:17.85: [44376]: <-- [9:AT+FTH=3\r]
Jan 17 14:30:20.30: [44376]: --> [0:]
Jan 17 14:30:20.30: [44376]: DELAY 100 ms
Jan 17 14:30:20.41: [44376]: <-- [5:ATH0\r]
Jan 17 14:30:25.42: [44376]: MODEM <Timeout>
Jan 17 14:30:25.42: [44376]: SESSION END
--
Daryl Sayers
Corinthian Engineering Ph: (02) 9906 7866
Suite 19, 401 Pacific Hwy Fax: (02) 9906 1556
Artarmon, NSW, 2064 email: daryl@ci.com.au
Australia www: http://www.cordoors.com.au
____________________ HylaFAX(tm) Users Mailing List _______________________
To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
