[hylafax-users] Unspecified Transmit Phase C error (Code 40)

To: <hylafax-users@hylafax.org>
Subject: [hylafax-users] Unspecified Transmit Phase C error (Code 40)
From: "Riki - Imap" <riki.scasi@libero.it>
Date: Fri, 19 Oct 2001 13:12:39 +0200

Hi all,

I'm trying to setup hylafax to send and receive faxes.
I currently have RedHat Linux 7.0 and I have installed Hylafax 4.1-1
(hylafax-4.1-1rh7.i386.rpm).
I have libtiff 3.5.5 installed.
My modem is an old external e-tech mod. E288c FaxModem (V.34) configured as
a class2 modem.
I had a problem sending a 'complex' fax (3 pages text/graphics) using Word
and WHFC, which wasn't delivered correctly (to more than a destination):
 - In one case the three pages were received, but the graphics were in part
not clear
 - In another case it was delivered three times the first page (partially
not clear)

(note that the same document was received perfectly)

here it follows  the log (quite long):

Oct 19 10:10:56.43: [ 4102]: SESSION BEGIN 00000034 392700441776
Oct 19 10:10:56.43: [ 4102]: HylaFAX (tm) Version 4.1
Oct 19 10:10:56.43: [ 4102]: SEND FAX: JOB 9 DEST 02700441776 COMMID
00000034
Oct 19 10:10:56.43: [ 4102]: DEVICE '/dev/ttyS0'
Oct 19 10:10:56.43: [ 4102]: DELAY 75 ms
Oct 19 10:10:56.51: [ 4102]: DELAY 2600 ms
Oct 19 10:10:59.11: [ 4102]: <-- [4:ATZ\r]
Oct 19 10:10:59.24: [ 4102]: --> [2:OK]
Oct 19 10:10:59.24: [ 4102]: <-- [5:ATE0\r]
Oct 19 10:10:59.35: [ 4102]: --> [4:ATE0]
Oct 19 10:10:59.35: [ 4102]: --> [2:OK]
Oct 19 10:10:59.35: [ 4102]: <-- [5:ATV1\r]
Oct 19 10:10:59.46: [ 4102]: --> [2:OK]
Oct 19 10:10:59.46: [ 4102]: <-- [5:ATQ0\r]
Oct 19 10:10:59.57: [ 4102]: --> [2:OK]
Oct 19 10:10:59.57: [ 4102]: <-- [7:ATS0=0\r]
Oct 19 10:10:59.69: [ 4102]: --> [2:OK]
Oct 19 10:10:59.69: [ 4102]: <-- [7:ATS8=2\r]
Oct 19 10:10:59.81: [ 4102]: --> [2:OK]
Oct 19 10:10:59.81: [ 4102]: <-- [8:ATS7=60\r]
Oct 19 10:10:59.93: [ 4102]: --> [2:OK]
Oct 19 10:10:59.93: [ 4102]: <-- [12:AT+FCLASS=2\r]
Oct 19 10:11:00.05: [ 4102]: --> [2:OK]
Oct 19 10:11:00.05: [ 4102]: <-- [10:AT+FTBC=0\r]
Oct 19 10:11:00.17: [ 4102]: --> [2:OK]
Oct 19 10:11:00.17: [ 4102]: <-- [10:AT+FBOR=0\r]
Oct 19 10:11:00.29: [ 4102]: --> [2:OK]
Oct 19 10:11:00.29: [ 4102]: <-- [13:AT+FPHCTO=30\r]
Oct 19 10:11:00.41: [ 4102]: --> [2:OK]
Oct 19 10:11:00.41: [ 4102]: <-- [24:AT+FDCC=1,5,0,2,0,0,0,0\r]
Oct 19 10:11:00.54: [ 4102]: --> [2:OK]
Oct 19 10:11:00.54: [ 4102]: <-- [5:ATM0\r]
Oct 19 10:11:00.67: [ 4102]: --> [2:OK]
Oct 19 10:11:00.67: [ 4102]: <-- [12:AT+FCLASS=2\r]
Oct 19 10:11:00.89: [ 4102]: --> [2:OK]
Oct 19 10:11:00.89: [ 4102]: <-- [10:AT+FTBC=0\r]
Oct 19 10:11:01.11: [ 4102]: --> [2:OK]
Oct 19 10:11:01.11: [ 4102]: <-- [10:AT+FBOR=0\r]
Oct 19 10:11:01.33: [ 4102]: --> [2:OK]
Oct 19 10:11:01.33: [ 4102]: <-- [13:AT+FPHCTO=30\r]
Oct 19 10:11:01.55: [ 4102]: --> [2:OK]
Oct 19 10:11:01.55: [ 4102]: <-- [24:AT+FDCC=1,5,0,2,0,0,0,0\r]
Oct 19 10:11:01.77: [ 4102]: --> [2:OK]
Oct 19 10:11:01.77: [ 4102]: <-- [25:AT+FLID="S.C.A.S.I. snc"\r]
Oct 19 10:11:02.00: [ 4102]: --> [2:OK]
Oct 19 10:11:02.02: [ 4102]: DIAL 02700441776
Oct 19 10:11:02.02: [ 4102]: <-- [16:ATDT02700441776\r]
Oct 19 10:11:12.22: [ 4102]: --> [5:+FCON]
Oct 19 10:11:13.83: [ 4102]: --> [28:+FCSI:"                    "]
Oct 19 10:11:13.83: [ 4102]: REMOTE CSI ""
Oct 19 10:11:14.19: [ 4102]: --> [21:+FDIS:1,5,0,2,0,0,0,0]
Oct 19 10:11:14.19: [ 4102]: --> [2:OK]
Oct 19 10:11:14.19: [ 4102]: REMOTE best rate 14400 bit/s
Oct 19 10:11:14.19: [ 4102]: REMOTE max page width 1728 pixels in 215 mm
Oct 19 10:11:14.19: [ 4102]: REMOTE max unlimited page length
Oct 19 10:11:14.19: [ 4102]: REMOTE best vres 7.7 line/mm
Oct 19 10:11:14.19: [ 4102]: REMOTE best format 1-D MR
Oct 19 10:11:14.19: [ 4102]: REMOTE best 0 ms/scanline
Oct 19 10:11:14.19: [ 4102]: USE 14400 bit/s
Oct 19 10:11:14.19: [ 4102]: USE 0 ms/scanline
Oct 19 10:11:14.19: [ 4102]: SEND file "docq/doc9.ps;01"
Oct 19 10:11:14.19: [ 4102]: USE page width 1728 pixels in 215 mm
Oct 19 10:11:14.19: [ 4102]: USE unlimited page length
Oct 19 10:11:14.19: [ 4102]: USE 7.7 line/mm
Oct 19 10:11:14.19: [ 4102]: USE 1-D MR
Oct 19 10:11:14.19: [ 4102]: <-- [7:AT+FDT\r]
Oct 19 10:11:21.68: [ 4102]: --> [21:+FDCS:1,5,0,2,0,0,0,0]
Oct 19 10:11:22.23: [ 4102]: --> [7:CONNECT]
Oct 19 10:11:22.23: [ 4102]: SEND wait for XON
Oct 19 10:11:22.23: [ 4102]: --> [1:]
Oct 19 10:11:22.23: [ 4102]: SEND begin page
Oct 19 10:12:46.09: [ 4102]: SENT 161485 bytes of data
Oct 19 10:12:46.60: [ 4102]: SEND end page
Oct 19 10:12:48.41: [ 4102]: --> [2:OK]
Oct 19 10:12:48.41: [ 4102]: SEND send MPS (more pages, same document)
Oct 19 10:12:48.41: [ 4102]: <-- [9:AT+FET=0\r]
Oct 19 10:12:51.74: [ 4102]: --> [7:+FPTS:2]
Oct 19 10:12:51.74: [ 4102]: --> [2:OK]
Oct 19 10:12:51.74: [ 4102]: SEND recv RTN (retrain negative)
Oct 19 10:12:51.74: [ 4102]: <-- [24:AT+FDIS=1,4,0,2,0,0,0,0\r]
Oct 19 10:12:51.97: [ 4102]: --> [2:OK]
Oct 19 10:12:51.97: [ 4102]: <-- [7:AT+FDT\r]
Oct 19 10:12:59.23: [ 4102]: --> [21:+FDCS:1,5,0,2,0,0,0,0]
Oct 19 10:12:59.78: [ 4102]: --> [7:CONNECT]
Oct 19 10:12:59.78: [ 4102]: SEND wait for XON
Oct 19 10:12:59.78: [ 4102]: --> [1:]
Oct 19 10:12:59.78: [ 4102]: SEND begin page
Oct 19 10:14:23.64: [ 4102]: SENT 161485 bytes of data
Oct 19 10:14:24.15: [ 4102]: SEND end page
Oct 19 10:14:24.25: [ 4102]: --> [2:OK]
Oct 19 10:14:24.25: [ 4102]: SEND send MPS (more pages, same document)
Oct 19 10:14:24.25: [ 4102]: <-- [9:AT+FET=0\r]
Oct 19 10:14:27.22: [ 4102]: --> [7:+FPTS:2]
Oct 19 10:14:27.22: [ 4102]: --> [2:OK]
Oct 19 10:14:27.22: [ 4102]: SEND recv RTN (retrain negative)
Oct 19 10:14:27.22: [ 4102]: <-- [24:AT+FDIS=1,3,0,2,0,0,0,0\r]
Oct 19 10:14:27.45: [ 4102]: --> [2:OK]
Oct 19 10:14:27.45: [ 4102]: <-- [7:AT+FDT\r]
Oct 19 10:14:34.71: [ 4102]: --> [21:+FDCS:1,5,0,2,0,0,0,0]
Oct 19 10:14:35.26: [ 4102]: --> [7:CONNECT]
Oct 19 10:14:35.26: [ 4102]: SEND wait for XON
Oct 19 10:14:35.26: [ 4102]: --> [1:]
Oct 19 10:14:35.26: [ 4102]: SEND begin page
Oct 19 10:15:59.12: [ 4102]: SENT 161485 bytes of data
Oct 19 10:15:59.63: [ 4102]: SEND end page
Oct 19 10:16:31.44: [ 4102]: --> [8:+FHNG:40]
Oct 19 10:16:31.44: [ 4102]: REMOTE HANGUP: Unspecified Transmit Phase C
error (code 40)
Oct 19 10:16:31.44: [ 4102]: --> [2:OK]
Oct 19 10:16:31.44: [ 4102]: <-- [5:ATH0\r]
Oct 19 10:16:31.65: [ 4102]: --> [2:OK]
Oct 19 10:16:31.65: [ 4102]: SESSION END

Can anybody help me?

Thanks
Riki



____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null

Follow-Ups:
- Re: [hylafax-users] Unspecified Transmit Phase C error (Code 40)
  - From: Lee Howard

Prev by Date: Re: [hylafax-users] Error converting data; command was "/usr/sbin/textfmt -B -f Courier-Bold
Next by Date: Re: [hylafax-users] sender variable in faxdispatch field
Previous by thread: [hylafax-users] avm c4 with 4 controllers
Next by thread: Re: [hylafax-users] Unspecified Transmit Phase C error (Code 40)
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services