[hylafax-users] Zyxel hangs

[Denis A Ustimenko <denis@oldham.ru>]

Hi there!

I have ZYXEL Omni56K/1.06 + hylafax 4.1 + Solaris 2.6. If I try to call to
modem then hang up it comes to "wedged" state:
-----------
Aug 08 10:38:35.38: [27774]: SESSION BEGIN 00000444 73832267460
Aug 08 10:38:35.38: [27774]: <-- [4:ATA\r]
Aug 08 10:39:19.44: [27774]: --> [7:+FHS:70]
Aug 08 10:39:19.44: [27774]: REMOTE HANGUP: Unspecified Receive Phase B
error (code 70)
Aug 08 10:39:19.44: [27774]: ANSWER: Ring detected without successful
handshake
Aug 08 10:39:19.44: [27774]: SESSION END
-----------
here is my config:
-----------
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2.0        # use class 2.0 interface
ModemRate:              38400           # 38.4 works fine
ModemFlowControl:       rtscts          # default
#
ModemNoFlowCmd:         AT&H0           # disable flow control
ModemHardFlowCmd:       AT&H3           # hardware flow control
ModemSoftFlowCmd:       AT&H4           # software flow control
ModemSetupDTRCmd:       AT&D2           # DTR off causes modem to hang up
ModemSetupDCDCmd:       AT&C1           # DCD tracks carrier
#
ModemSetupAACmd:        AT+FAA=1        # enable in current class
#
# Additional reset commands:
#
# &B1     DTE-DCE rate is fixed at DTE setting
# &N0     Auto-negotiate highest possible DCE-DCE link rate
# &S0     DSR always on
# *F0     Deny remote configuration
#         (actually *F0 doesn't work in the firmware -- sigh)
# S18=4   Receive at 38400
# S38.3=1 DCD on/off sequence follows UNIX standard; also
#         fix receiving baud rate at S18 value
#
ModemResetCmds:         ATZ&B1&N0&S0S18=4S38.3=1
#

#
# We don't want unlimited page length
# original Omni was: (0,1),(0-5),(0-2),(0-2),(0,1),(0),(0),(0-7)
#
# A4 length:
Class2DCCQueryCmd:      !(0,1),(0-5),(0-2),0,(0,1),(0),(0),(0-7)
#
# A4,B4 length:
#
#Class2DCCQueryCmd:     !(0,1),(0-5),(0-2),(0,1),(0,1),(0),(0),(0-7)
#

ModemDialCmd:           ATDT%s          # no '@' 'cuz then busy not
recognized
NoCarrierRetrys:        3               # retry 3 times on no carrier
#
ModemSetVolumeCmd:      "ATM0 ATM1L1 ATM1L3 ATM1L5 ATM1L7"
#
# Caller ID configuration setup.
#
#QualifyCID:            etc/cid         # CID access control list file
#CIDNumber:             "CALLER NUMBER: " # pattern string for phone
number info
#CIDName:               "CALLER NAME: " # pattern string for identity info
#
PagerSetupCmds:         AT&K0&N15       # use V.22 at 1200 bps (PageNet)
------------
Does anyone know what's the matter?

Regards
Denis



____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null