[hylafax-users] Multi page fax and RC2

[Stephan Bauer <stephan_bauer@gmx.de>]

Hello,

I cant get multi page faxes with RC2.
The first page is ok, e.g.
RECV: 2233 total lines, 0 bad lines, 1 consecutive bad

The next pages didnt have any lines, e.g.
RECV: 0 total lines, 0 bad lines, 0 consecutive bad lines

I tried also the CVS version.

It works with beta3.
My config is attatched.

Regards

Stephan Bauer
# $Id: class1,v 1.4 2001/05/21 04:31:28 darren Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Generic Class 1 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:		49
AreaCode:		7306
FAXNumber:		+49.7306.919594
LongDistancePrefix:	0
InternationalPrefix:	00
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0644
LogFileMode:		0644
DeviceMode:		0600
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"r -b -s %s %l"
LocalIdentifier:	"Kling & Bauer"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"%%l|%c|Seite %%P von %%T"
PercentGoodLines:	80
MaxConsecutiveBadLines:	10
MaxRecvPages:		50
JobReqNoCarrier:	180
JobReqNoAnswer:		180
JobReqDataConn:		180
JobReqOther:		180
RecvDataFormat:		"1-D MR"
Use2D:			No
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		# use this to supply a hint
#ModemRate:		19200		# rate for DCE-DTE communication
#ModemFlowControl:	xonxoff		# XON/XOFF flow control assumed
#
#ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
#ModemSetupDCDCmd:	AT&C1		# setup so DCD follows carrier
#GettyArgs:		"-h %l dx_%s"	# modem must auto-detect fax/data
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd:		ATDT%s@		# T for tone dialing, @ for silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds:		"AT&E919594"		# stuff to do when modem is reset
#ModemAnswerCmd:		ATA		# use this to answer phone
#ModemNoFlowCmd:		AT&K		# disable flow control cmd
#ModemHardFlowCmd:	AT&K3		# hardware flow control cmd
#ModemSoftFlowCmd:	AT&K4		# software flow control cmd
#ModemNoAutoAnswerCmd:	ATS0=0		# disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd:	"ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd:	ATE0		# disable command echo
#ModemVerboseResultsCmd:	ATV1		# enable verbose command results
#ModemResultCodesCmd:	ATQ0		# enable result codes
#ModemOnHookCmd:		ATH0		# place phone on hook (hangup)
#ModemSoftResetCmd:	ATZ		# do soft reset of modem
#ModemWaitTimeCmd:	ATS7=60		# wait 60 seconds for carrier
#ModemCommaPauseTimeCmd:	ATS8=2		# comma pause time is 2 seconds
#ModemRecvFillOrder:	LSB2MSB		# bit order of received facsimile
#ModemSendFillOrder:	LSB2MSB		# bit order modem expects for transmit
#
Class1Cmd:		AT+FCLASS=1	# command to enter class 1
Class1TCFResponseDelay:	75		# 75ms delay between recv TCF & response
Class1SendPPMDelay:	75		# 75ms delay before sending PPM
Class1SendTCFDelay:	75		# 75ms delay between sending DCS & TCF
Class1SwitchingDelay:	150		# 150ms delay in switching transmission direction
Class1TrainingRecovery:	1500		# 1.5sec delay after training failure
Class1RecvAbortOK:	200		# wait 200ms for abort response
Class1FrameOverhead:	4		# 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer:	40000		# 35+5secs waiting for ident frames
Class1TCFMaxNonZero:	10		# max 10% of data may be non-zero
Class1TCFMinRun:	1000		# min run is 2/3rds of TCF duration