[hylafax-users] Incoming Faxes are being scrambled

To: <hylafax-users@hylafax.org>
Subject: [hylafax-users] Incoming Faxes are being scrambled
From: "Dennis Fellows" <dennis@lamtop.com>
Date: Thu, 5 Apr 2001 13:01:40 -0500
I sent a question yesterday but I was not subscribing to this list. So I am
resending this question but I also have some followup info.

I am running RH7.0, Hyla-Fax 4.1beta2 (binary
hylafax-4.1beta2-2rh7.i386.rpm), libtiff 3.4 (developer beta037-4),
Multitech 2834ZDX modems (four of 'em), and a RocketPort multi-I/O card.

I have had problems receiving faxes with this set up from certain senders.
When I receive thier transmission all I get is a garbled tiff that is
usually just an inch or more of legible text and then the rest is black
lines and speckles. The sender would get a successful transmission reprot
from his fax machine. When I have the sender send the fax to a standalone
fax machine (Richoh), the fax will be successful. When I send from my Richoh
to my HylaFax server it has no problems.

I was very puzzled because the log reported no errors (see below).
Apr 04 09:24:44.78: [ 4447]: SESSION BEGIN 00000005 12626584184
Apr 04 09:24:44.78: [ 4447]: <-- [4:ATA\r]
Apr 04 09:24:54.69: [ 4447]: --> [5:+FCON]
Apr 04 09:24:54.69: [ 4447]: ANSWER: FAX CONNECTION
Apr 04 09:24:54.69: [ 4447]: RECV FAX: begin
Apr 04 09:24:59.93: [ 4447]: --> [28:+FTSI:"          6082407266"]
Apr 04 09:24:59.93: [ 4447]: REMOTE TSI "6082407266"
Apr 04 09:24:59.93: [ 4447]: --> [21:+FDCS:0,5,0,2,1,0,0,3]
Apr 04 09:24:59.93: [ 4447]: REMOTE wants 14400 bit/s
Apr 04 09:24:59.93: [ 4447]: REMOTE wants page width 1728 pixels in 215 mm
Apr 04 09:24:59.93: [ 4447]: REMOTE wants unlimited page length
Apr 04 09:24:59.93: [ 4447]: REMOTE wants 3.85 line/mm
Apr 04 09:24:59.93: [ 4447]: REMOTE wants 2-D MR
Apr 04 09:24:59.93: [ 4447]: --> [2:OK]
Apr 04 09:24:59.93: [ 4447]: <-- [7:AT+FDR\r]
Apr 04 09:25:01.35: [ 4447]: --> [5:+FCFR]
Apr 04 09:25:01.35: [ 4447]: --> [28:+FTSI:"          6082407266"]
Apr 04 09:25:01.35: [ 4447]: REMOTE TSI "6082407266"
Apr 04 09:25:01.35: [ 4447]: --> [21:+FDCS:0,5,0,2,1,0,0,3]
Apr 04 09:25:01.35: [ 4447]: REMOTE wants 14400 bit/s
Apr 04 09:25:01.35: [ 4447]: REMOTE wants page width 1728 pixels in 215 mm
Apr 04 09:25:01.35: [ 4447]: REMOTE wants unlimited page length
Apr 04 09:25:01.35: [ 4447]: REMOTE wants unlimited page length
Apr 04 09:25:01.35: [ 4447]: REMOTE wants 3.85 line/mm
Apr 04 09:25:01.35: [ 4447]: REMOTE wants 2-D MR
Apr 04 09:25:02.86: [ 4447]: --> [7:CONNECT]
Apr 04 09:25:02.86: [ 4447]: RECV: begin page
Apr 04 09:25:02.86: [ 4447]: RECV: send trigger 022
Apr 04 09:25:02.86: [ 4447]: <-- data [1]
Apr 04 09:25:18.08: [ 4447]: RECV: 25322 bytes of data, 261 total lines
Apr 04 09:25:18.19: [ 4447]: --> [15:+FPTS:1,0,0,0,0]
Apr 04 09:25:19.48: [ 4447]: --> [6:+FET:2]
Apr 04 09:25:19.48: [ 4447]: RECV recv EOP (no more pages or documents)
Apr 04 09:25:19.48: [ 4447]: --> [2:OK]
Apr 04 09:25:19.48: [ 4447]: RECV send MCF (message confirmation)
Apr 04 09:25:19.48: [ 4447]: RECV FAX (00000005): from 6082407266, page 1 in
0:2
0, INF, 3.85 line/mm, 2-D MR, 14400 bit/s
Apr 04 09:25:19.48: [ 4447]: RECV FAX (00000005): recvq/fax00005.tif from
608240
7266, route to <unspecified>, 1 pages in 0:25
Apr 04 09:25:19.48: [ 4447]: <-- [7:AT+FDR\r]
Apr 04 09:25:22.53: [ 4447]: --> [7:+FHNG:0]
Apr 04 09:25:22.53: [ 4447]: REMOTE HANGUP: Normal and proper end of
connection
(code 0)
Apr 04 09:25:22.53: [ 4447]: RECV FAX: bin/faxrcvd "recvq/fax00005.tif"
"ttyR1"
"00000005" ""
Apr 04 09:25:01.35: [ 4447]: REMOTE wants 2-D MR
Apr 04 09:25:02.86: [ 4447]: --> [7:CONNECT]
Apr 04 09:25:02.86: [ 4447]: RECV: begin page
Apr 04 09:25:02.86: [ 4447]: RECV: send trigger 022
Apr 04 09:25:02.86: [ 4447]: <-- data [1]
Apr 04 09:25:18.08: [ 4447]: RECV: 25322 bytes of data, 261 total lines
Apr 04 09:25:18.19: [ 4447]: --> [15:+FPTS:1,0,0,0,0]
Apr 04 09:25:19.48: [ 4447]: --> [6:+FET:2]
Apr 04 09:25:19.48: [ 4447]: RECV recv EOP (no more pages or documents)
Apr 04 09:25:19.48: [ 4447]: --> [2:OK]
Apr 04 09:25:19.48: [ 4447]: RECV send MCF (message confirmation)
Apr 04 09:25:19.48: [ 4447]: RECV FAX (00000005): from 6082407266, page 1 in
0:2
0, INF, 3.85 line/mm, 2-D MR, 14400 bit/s
Apr 04 09:25:19.48: [ 4447]: RECV FAX (00000005): recvq/fax00005.tif from
608240
7266, route to <unspecified>, 1 pages in 0:25
Apr 04 09:25:19.48: [ 4447]: <-- [7:AT+FDR\r]
Apr 04 09:25:22.53: [ 4447]: --> [7:+FHNG:0]
Apr 04 09:25:22.53: [ 4447]: REMOTE HANGUP: Normal and proper end of
connection
(code 0)
Apr 04 09:25:22.53: [ 4447]: RECV FAX: bin/faxrcvd "recvq/fax00005.tif"
"ttyR1"
"00000005" ""
Apr 04 09:25:22.64: [ 4447]: RECV FAX: end
Apr 04 09:25:22.64: [ 4447]: SESSION END

Now today, there were no problems with incoming faxes. Yet NO CHANGES were
made! Here's a log from a successful receive (see below):

Apr 05 09:22:46.16: [  916]: SESSION BEGIN 00000022 12626584152
Apr 05 09:22:46.16: [  916]: <-- [4:ATA\r]
Apr 05 09:22:55.77: [  916]: --> [5:+FCON]
Apr 05 09:22:55.77: [  916]: ANSWER: FAX CONNECTION
Apr 05 09:22:55.77: [  916]: RECV FAX: begin
Apr 05 09:23:01.00: [  916]: --> [28:+FTSI:"          6082407266"]
Apr 05 09:23:01.00: [  916]: REMOTE TSI "6082407266"
Apr 05 09:23:01.00: [  916]: --> [21:+FDCS:0,5,0,2,1,0,0,3]
Apr 05 09:23:01.00: [  916]: REMOTE wants 14400 bit/s
Apr 05 09:23:01.00: [  916]: REMOTE wants page width 1728 pixels in 215 mm
Apr 05 09:23:01.00: [  916]: REMOTE wants unlimited page length
Apr 05 09:23:01.00: [  916]: REMOTE wants 3.85 line/mm
Apr 05 09:23:01.00: [  916]: REMOTE wants 2-D MR
Apr 05 09:23:01.00: [  916]: --> [2:OK]
Apr 05 09:23:01.00: [  916]: <-- [7:AT+FDR\r]
Apr 05 09:23:02.45: [  916]: --> [5:+FCFR]
Apr 05 09:23:02.45: [  916]: --> [28:+FTSI:"          6082407266"]
Apr 05 09:23:02.45: [  916]: REMOTE TSI "6082407266"
Apr 05 09:23:02.45: [  916]: --> [21:+FDCS:0,5,0,2,1,0,0,3]
Apr 05 09:23:02.45: [  916]: REMOTE wants 14400 bit/s
Apr 05 09:23:02.45: [  916]: REMOTE wants page width 1728 pixels in 215 mm
Apr 05 09:23:02.45: [  916]: REMOTE wants unlimited page length
Apr 05 09:23:02.45: [  916]: REMOTE wants unlimited page length
Apr 05 09:23:02.45: [  916]: REMOTE wants 3.85 line/mm
Apr 05 09:23:02.45: [  916]: REMOTE wants 2-D MR
Apr 05 09:23:03.95: [  916]: --> [7:CONNECT]
Apr 05 09:23:03.95: [  916]: RECV: begin page
Apr 05 09:23:03.95: [  916]: RECV: send trigger 022
Apr 05 09:23:03.95: [  916]: <-- data [1]
Apr 05 09:23:19.64: [  916]: RECV: 26700 bytes of data, 1060 total lines
Apr 05 09:23:19.64: [  916]: --> [15:+FPTS:1,0,0,0,0]
Apr 05 09:23:20.92: [  916]: --> [6:+FET:2]
Apr 05 09:23:20.92: [  916]: RECV recv EOP (no more pages or documents)
Apr 05 09:23:20.92: [  916]: --> [2:OK]
Apr 05 09:23:20.92: [  916]: RECV send MCF (message confirmation)
Apr 05 09:23:20.92: [  916]: RECV FAX (00000022): from 6082407266, page 1 in
0:1
9, INF, 3.85 line/mm, 2-D MR, 14400 bit/s
Apr 05 09:23:20.92: [  916]: RECV FAX (00000022): recvq/fax00018.tif from
608240
7266, route to <unspecified>, 1 pages in 0:25
Apr 05 09:23:20.92: [  916]: <-- [7:AT+FDR\r]
Apr 05 09:23:24.02: [  916]: --> [7:+FHNG:0]
Apr 05 09:23:24.02: [  916]: REMOTE HANGUP: Normal and proper end of
connection
(code 0)
Apr 05 09:23:24.02: [  916]: RECV FAX: bin/faxrcvd "recvq/fax00018.tif"
"ttyR0"
"00000022" ""
Apr 05 09:23:02.45: [  916]: REMOTE wants 2-D MR
Apr 05 09:23:03.95: [  916]: --> [7:CONNECT]
Apr 05 09:23:03.95: [  916]: RECV: begin page
Apr 05 09:23:03.95: [  916]: RECV: send trigger 022
Apr 05 09:23:03.95: [  916]: <-- data [1]
Apr 05 09:23:19.64: [  916]: RECV: 26700 bytes of data, 1060 total lines
Apr 05 09:23:19.64: [  916]: --> [15:+FPTS:1,0,0,0,0]
Apr 05 09:23:20.92: [  916]: --> [6:+FET:2]
Apr 05 09:23:20.92: [  916]: RECV recv EOP (no more pages or documents)
Apr 05 09:23:20.92: [  916]: --> [2:OK]
Apr 05 09:23:20.92: [  916]: RECV send MCF (message confirmation)
Apr 05 09:23:20.92: [  916]: RECV FAX (00000022): from 6082407266, page 1 in
0:1
9, INF, 3.85 line/mm, 2-D MR, 14400 bit/s
Apr 05 09:23:20.92: [  916]: RECV FAX (00000022): recvq/fax00018.tif from
608240
7266, route to <unspecified>, 1 pages in 0:25
Apr 05 09:23:20.92: [  916]: <-- [7:AT+FDR\r]
Apr 05 09:23:24.02: [  916]: --> [7:+FHNG:0]
Apr 05 09:23:24.02: [  916]: REMOTE HANGUP: Normal and proper end of
connection
(code 0)
Apr 05 09:23:24.02: [  916]: RECV FAX: bin/faxrcvd "recvq/fax00018.tif"
"ttyR0"
"00000022" ""
Apr 05 09:23:24.13: [  916]: RECV FAX: end
Apr 05 09:23:24.13: [  916]: SESSION END

I decided to use one of the suggestions I recently read to have the modem
perform QC on the line so I implemented the command in the config.ttyR0
script (and my other three lines): Class2CQQueryCmd: "!(0),(0)".

Upon doing that (I had to let one incoming fax go through before the command
took hold) suddenly I began receving major errors and the fax was rejected!
This happened with my "sure bet" Richoh which had never failed to send a fax
to my Hylafax server. Here's the log....
Apr 05 11:15:56.63: [  916]: SESSION BEGIN 00000028 12626584152
Apr 05 11:15:56.63: [  916]: <-- [4:ATA\r]
Apr 05 11:16:04.73: [  916]: --> [5:+FCON]
Apr 05 11:16:04.73: [  916]: ANSWER: FAX CONNECTION
Apr 05 11:16:04.73: [  916]: RECV FAX: begin
Apr 05 11:16:10.05: [  916]: --> [28:+FTSI:"          2626584152"]
Apr 05 11:16:10.05: [  916]: REMOTE TSI "2626584152"
Apr 05 11:16:10.05: [  916]: --> [21:+FDCS:0,5,0,2,1,0,0,1]
Apr 05 11:16:10.05: [  916]: REMOTE wants 14400 bit/s
Apr 05 11:16:10.05: [  916]: REMOTE wants page width 1728 pixels in 215 mm
Apr 05 11:16:10.05: [  916]: REMOTE wants unlimited page length
Apr 05 11:16:10.05: [  916]: REMOTE wants 3.85 line/mm
Apr 05 11:16:10.05: [  916]: REMOTE wants 2-D MR
Apr 05 11:16:10.05: [  916]: --> [2:OK]
Apr 05 11:16:10.05: [  916]: <-- [7:AT+FDR\r]
Apr 05 11:16:11.52: [  916]: --> [5:+FCFR]
Apr 05 11:16:11.52: [  916]: --> [28:+FTSI:"          2626584152"]
Apr 05 11:16:11.52: [  916]: REMOTE TSI "2626584152"
Apr 05 11:16:11.52: [  916]: --> [21:+FDCS:0,5,0,2,1,0,0,1]
Apr 05 11:16:11.52: [  916]: REMOTE wants 14400 bit/s
Apr 05 11:16:11.52: [  916]: REMOTE wants page width 1728 pixels in 215 mm
Apr 05 11:16:11.52: [  916]: REMOTE wants unlimited page length
Apr 05 11:16:11.52: [  916]: REMOTE wants unlimited page length
Apr 05 11:16:11.52: [  916]: REMOTE wants 3.85 line/mm
Apr 05 11:16:11.52: [  916]: REMOTE wants 2-D MR
Apr 05 11:16:12.40: [  916]: --> [7:CONNECT]
Apr 05 11:16:12.40: [  916]: RECV: begin page
Apr 05 11:16:12.40: [  916]: RECV: send trigger 022
Apr 05 11:16:12.40: [  916]: <-- data [1]
Apr 05 11:16:28.68: [  916]: RECV: 1048 total lines, 976 bad lines, 60
consecuti
ve bad lines
Apr 05 11:16:28.68: [  916]: --> [15:+FPTS:1,0,0,0,0]
Apr 05 11:16:29.96: [  916]: --> [6:+FET:0]
Apr 05 11:16:29.96: [  916]: RECV recv MPS (more pages, same document)
Apr 05 11:16:29.96: [  916]: --> [2:OK]
Apr 05 11:16:29.96: [  916]: RECV: REJECT page quality, 6% good lines (95%
requi
red)
Apr 05 11:16:29.96: [  916]: RECV send RTN (retrain negative)
Apr 05 11:16:29.96: [  916]: <-- [10:AT+FPTS=2\r]
Apr 05 11:16:30.22: [  916]: --> [2:OK]
Apr 05 11:16:30.22: [  916]: <-- [7:AT+FDR\r]
Apr 05 11:16:38.46: [  916]: --> [5:+FCFR]
Apr 05 11:16:38.46: [  916]: --> [28:+FTSI:"          2626584152"]
Apr 05 11:16:38.46: [  916]: REMOTE TSI "2626584152"
Apr 05 11:16:38.46: [  916]: --> [21:+FDCS:0,5,0,2,1,0,0,1]
Apr 05 11:16:38.46: [  916]: --> [21:+FDCS:0,5,0,2,1,0,0,1]
Apr 05 11:16:38.46: [  916]: REMOTE wants 14400 bit/s
Apr 05 11:16:38.46: [  916]: REMOTE wants page width 1728 pixels in 215 mm
Apr 05 11:16:38.46: [  916]: REMOTE wants unlimited page length
Apr 05 11:16:38.46: [  916]: REMOTE wants 3.85 line/mm
Apr 05 11:16:38.46: [  916]: REMOTE wants 2-D MR
Apr 05 11:16:39.32: [  916]: --> [7:CONNECT]
Apr 05 11:16:39.32: [  916]: RECV: begin page
Apr 05 11:16:39.32: [  916]: RECV: send trigger 022
Apr 05 11:16:39.32: [  916]: <-- data [1]
Apr 05 11:16:55.49: [  916]: RECV: 1050 total lines, 978 bad lines, 60
consecuti
ve bad lines
Apr 05 11:16:55.49: [  916]: --> [15:+FPTS:1,0,0,0,0]
Apr 05 11:16:56.89: [  916]: --> [6:+FET:0]
Apr 05 11:16:56.89: [  916]: RECV recv MPS (more pages, same document)
Apr 05 11:16:56.89: [  916]: --> [2:OK]
Apr 05 11:16:56.89: [  916]: RECV: REJECT page quality, 6% good lines (95%
requi
red)
Apr 05 11:16:56.89: [  916]: RECV send RTN (retrain negative)
Apr 05 11:16:56.89: [  916]: <-- [10:AT+FPTS=2\r]
Apr 05 11:16:57.15: [  916]: --> [2:OK]
Apr 05 11:16:57.15: [  916]: <-- [7:AT+FDR\r]
Apr 05 11:17:05.37: [  916]: --> [5:+FCFR]
Apr 05 11:17:05.37: [  916]: --> [5:+FCFR]
Apr 05 11:17:05.37: [  916]: --> [28:+FTSI:"          2626584152"]
Apr 05 11:17:05.37: [  916]: REMOTE TSI "2626584152"
Apr 05 11:17:05.37: [  916]: --> [21:+FDCS:0,5,0,2,1,0,0,1]
Apr 05 11:17:05.37: [  916]: REMOTE wants 14400 bit/s
Apr 05 11:17:05.37: [  916]: REMOTE wants page width 1728 pixels in 215 mm
Apr 05 11:17:05.37: [  916]: REMOTE wants unlimited page length
Apr 05 11:17:05.37: [  916]: REMOTE wants 3.85 line/mm
Apr 05 11:17:05.37: [  916]: REMOTE wants 2-D MR
Apr 05 11:17:06.23: [  916]: --> [7:CONNECT]
Apr 05 11:17:06.23: [  916]: RECV: begin page
Apr 05 11:17:06.23: [  916]: RECV: send trigger 022
Apr 05 11:17:06.23: [  916]: <-- data [1]
Apr 05 11:17:22.51: [  916]: RECV: 1050 total lines, 982 bad lines, 60
consecuti
ve bad lines
Apr 05 11:17:22.51: [  916]: --> [15:+FPTS:1,0,0,0,0]
Apr 05 11:17:23.79: [  916]: --> [6:+FET:0]
Apr 05 11:17:23.79: [  916]: RECV recv MPS (more pages, same document)
Apr 05 11:17:23.79: [  916]: --> [2:OK]
Apr 05 11:17:23.79: [  916]: RECV: REJECT page quality, 6% good lines (95%
requi
red)
Apr 05 11:17:23.79: [  916]: RECV send RTN (retrain negative)
Apr 05 11:17:23.79: [  916]: <-- [10:AT+FPTS=2\r]
Apr 05 11:17:23.79: [  916]: <-- [10:AT+FPTS=2\r]
Apr 05 11:17:24.05: [  916]: --> [2:OK]
Apr 05 11:17:24.05: [  916]: <-- [7:AT+FDR\r]
Apr 05 11:17:32.29: [  916]: --> [5:+FCFR]
Apr 05 11:17:32.29: [  916]: --> [28:+FTSI:"          2626584152"]
Apr 05 11:17:32.29: [  916]: REMOTE TSI "2626584152"
Apr 05 11:17:32.29: [  916]: --> [21:+FDCS:0,5,0,2,1,0,0,1]
Apr 05 11:17:32.29: [  916]: REMOTE wants 14400 bit/s
Apr 05 11:17:32.29: [  916]: REMOTE wants page width 1728 pixels in 215 mm
Apr 05 11:17:32.29: [  916]: REMOTE wants unlimited page length
Apr 05 11:17:32.29: [  916]: REMOTE wants 3.85 line/mm
Apr 05 11:17:32.29: [  916]: REMOTE wants 2-D MR
Apr 05 11:17:33.15: [  916]: --> [7:CONNECT]
Apr 05 11:17:33.15: [  916]: RECV: begin page
Apr 05 11:17:33.15: [  916]: RECV: send trigger 022
Apr 05 11:17:33.15: [  916]: <-- data [1]
Apr 05 11:17:49.43: [  916]: RECV: 1050 total lines, 986 bad lines, 60
consecuti
ve bad lines
Apr 05 11:17:49.43: [  916]: --> [15:+FPTS:1,0,0,0,0]
Apr 05 11:17:50.72: [  916]: --> [6:+FET:0]
Apr 05 11:17:50.72: [  916]: RECV recv MPS (more pages, same document)
Apr 05 11:17:50.72: [  916]: --> [2:OK]
Apr 05 11:17:50.72: [  916]: RECV: REJECT page quality, 6% good lines (95%
requi
Apr 05 11:17:49.43: [  916]: RECV: 1050 total lines, 986 bad lines, 60
consecuti
ve bad lines
Apr 05 11:17:49.43: [  916]: --> [15:+FPTS:1,0,0,0,0]
Apr 05 11:17:50.72: [  916]: --> [6:+FET:0]
Apr 05 11:17:50.72: [  916]: RECV recv MPS (more pages, same document)
Apr 05 11:17:50.72: [  916]: --> [2:OK]
Apr 05 11:17:50.72: [  916]: RECV: REJECT page quality, 6% good lines (95%
requi
red)
Apr 05 11:17:50.72: [  916]: RECV send RTN (retrain negative)
Apr 05 11:17:50.72: [  916]: <-- [10:AT+FPTS=2\r]
Apr 05 11:17:50.98: [  916]: --> [2:OK]
Apr 05 11:17:50.98: [  916]: <-- [7:AT+FDR\r]
Apr 05 11:17:53.93: [  916]: --> [8:+FHNG:72]
Apr 05 11:17:53.93: [  916]: REMOTE HANGUP: COMREC error (code 72)
Apr 05 11:17:53.93: [  916]: RECV FAX (00000028): recvq/fax00024.tif from
262658
4152, route to <unspecified>, 0 pages in 1:49
Apr 05 11:17:53.93: [  916]: RECV FAX: COMREC error
Apr 05 11:17:53.93: [  916]: RECV FAX (00000028): session with 2626584152
termin
ated abnormally: COMREC error
Apr 05 11:17:53.93: [  916]: RECV FAX: bin/faxrcvd "recvq/fax00024.tif"
"ttyR0"
"00000028" "COMREC error"
Apr 05 11:17:54.03: [  916]: RECV FAX: end
Apr 05 11:17:54.03: [  916]: SESSION END

After commenting out the QC line. Things are back to "normal". Here's my
config script (you'll see the QC line commented out):

# $Id: mt-1432,v 1.1.1.1 1998/10/12 20:47:47 root Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names
of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#

#
# Configuration for a Multi-Tech MT1432, MT224BA, and MT1932ZDX modems.
#
# MT1432        firmware rev 0307 I or newer
# MT132BG       rev 0109A
# MT1932ZDX     rev 0109H
#
# Note that MT1432 modems come in several varieties:
#
# MT1432BA      uses Rockwell data pump
# MT1432BA/A    uses AT&T data pump
# MT1432BG      MT1432BA tweaked for German FCC
# MT1432MK      (for UK?)
#
# The modem has been tried with both XON/XOFF and RTS/CTS flow
# control; this configuration is for hardware flow control.
# control; this configuration is for hardware flow control.
#
#
CountryCode:            1
AreaCode:               262
FAXNumber:              1.262.658.4152
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "Laminated Products x4152"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%p of %%t"
MaxRecvPages:           250
#
#
TagLineFormat:          "From %%l|%c|Page %%p of %%t"
MaxRecvPages:           250
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2          # use class 2 interface
ModemRate:              57600           # lock rate for DCE-DTE
communication
ModemFlowControl:       rtscts          # default
#
ModemHardFlowCmd:       AT&E4           # hardware flow control
ModemSoftFlowCmd:       AT&E5           # software flow control
ModemSetupDTRCmd:       AT&D3           # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or
not)
ModemSetupAACmd:        AT+FAA=1        # enable adaptive-answer in class 2
#
# NB: some models get confused by the @
#
ModemDialCmd:           ATDT%s@         # T for tone dialing, @ for silence
#
Class2RecvDataTrigger:  "\022"          # character sent to modem to start
recv
#Class2CQQueryCmd:      "!(0),(0)"      # Enable Quality Check by DF 040501


Any help would be greatly appreciated! I have read some people being given
the suggestion of going to Class 1 faxing but we need to send and receive
faxes. I am lead to believe that I need Class2 to do both. Correct me if I'm
not right in that thought.

Best Regards,
Dennis Fellows
dennis@lamtop.com



____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
Follow-Ups:
- Re: [hylafax-users] Incoming Faxes are being scrambled
  - From: Lee Howard <faxguy@deanox.com>
Prev by Date: Re: [hylafax-users] Hylafax installed properly on Suse 6.4
Next by Date: Re: [hylafax-users] Incoming Faxes are being scrambled
Prev by thread: [hylafax-users] VIRUS IN A MAIL FOR YOU FROM fcartron@apm-online.fr
Next by thread: Re: [hylafax-users] Incoming Faxes are being scrambled
Index(es):
- Main
- Thread
Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services