|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] hylafax and isdn
Hi,
I have the same card with me and trying deparately get it going for
HylaFax.. But still no luck.. I got the following mail from Melware people
who develop Linux Drivers for Eicon cards. It might give you an idea the
state of the drivers. I was able to get up to some extent but the behavior
of the ttyI driver with hylafax is very odd.
I'm stuck at the situation discribed in the follwing mail. Any comments are
greatly appriciated!
Best Regards,
Ruwan Jayanetti.
--------------------------------------------------------------------------------
Date: Thu, 22 Mar 2001 21:11:30 +0100
From: Ralf Spachmann <mel@melware.de>
To: rjayanetti@www.com
Cc: "Armin Schindler techn. dev" <armins@melware.de>
Subject: Re: ttyIs Diva Server BRI
--------------------------------------------------------------------------------
Hi,
there are no known problems related to our driver using fax-capabilities.
We have a lot of customers using various eicon cards w/o any difficulties
under
Linux as a Fax-Server.
Which driver for your eicon-card do you use ? In case of legacy eicon,
please
update to our latest release of DIVAS driver (www.melware.net for
details/dnl)
Obviously there seem to exist an CAPI2.0 adoption for Hylafax, which could
be
useful since the new DIVAS driver has full CAPI20 support, too.
For more details about configuring Hylafax, the Hylafax-peoples FAQ and
websites
may be helpful !
Best Regards
Ralf Spachmann, CM
-------
On 22 Mar 2001 03:59:29 -0800
rjayanetti@www.com wrote:
> Hi,
> I’m trying to use HylaFax with Diva Serer 2M BRI ISDN card on SUSE
>Linux 7.0
distribution. I use ttyI interface for HylaFax to use ISDN. I have two major
problems.
> 1. When sending fax at one point HylaFax drops the connection and at the
receiving fax machine I get “Communication Error”. HylaFax Log follows.
> Mar 22 10:30:08.71: [ 727]: SESSION BEGIN 00000010 941650912
> Mar 22 10:30:08.71: [ 727]: SEND FAX: JOB 3 DEST 01650912 COMMID
>00000010
> Mar 22 10:30:08.71: [ 727]: MODEM set DTR OFF
> Mar 22 10:30:11.30: [ 727]: MODEM set DTR ON
> Mar 22 10:30:11.30: [ 727]: MODEM set baud rate: 19200 baud, input flow
>NONE,
output flow NONE
> Mar 22 10:30:11.30: [ 727]: MODEM flush i/o
> Mar 22 10:30:11.30: [ 727]: <-- [28:ATZ&E0S0=1S13=1E0V1Q0S0=0H0\r]
> Mar 22 10:30:11.31: [ 727]: --> [2:OK]
> Mar 22 10:30:11.31: [ 727]: <-- [12:ATS8=2S7=60\r]
> Mar 22 10:30:11.32: [ 727]: --> [2:OK]
> Mar 22 10:30:11.32: [ 727]: <-- [12:AT+FCLASS=2\r]
> Mar 22 10:30:11.33: [ 727]: --> [2:OK]
> Mar 22 10:30:11.33: [ 727]: <-- [10:AT+FTBC=0\r]
> Mar 22 10:30:11.34: [ 727]: --> [2:OK]
> Mar 22 10:30:11.34: [ 727]: <-- [10:AT+FBOR=0\r]
> Mar 22 10:30:11.35: [ 727]: --> [2:OK]
> Mar 22 10:30:11.35: [ 727]: <-- [13:AT+FPHCTO=30\r]
> Mar 22 10:30:11.36: [ 727]: --> [2:OK]
> Mar 22 10:30:11.36: [ 727]: <-- [24:AT+FDCC=1,5,2,2,3,0,0,0\r]
> Mar 22 10:30:11.37: [ 727]: --> [2:OK]
> Mar 22 10:30:11.37: [ 727]: <-- [5:ATM0\r]
> Mar 22 10:30:11.38: [ 727]: --> [2:OK]
> Mar 22 10:30:11.38: [ 727]: MODEM input buffering enabled
> Mar 22 10:30:11.38: [ 727]: <-- [12:AT+FCLASS=2\r]
> Mar 22 10:30:11.49: [ 727]: --> [2:OK]
> Mar 22 10:30:11.49: [ 727]: <-- [10:AT+FTBC=0\r]
> Mar 22 10:30:11.60: [ 727]: --> [2:OK]
> Mar 22 10:30:11.60: [ 727]: <-- [10:AT+FBOR=0\r]
> Mar 22 10:30:11.71: [ 727]: --> [2:OK]
> Mar 22 10:30:11.71: [ 727]: <-- [13:AT+FPHCTO=30\r]
> Mar 22 10:30:11.82: [ 727]: --> [2:OK]
> Mar 22 10:30:11.82: [ 727]: <-- [24:AT+FDCC=1,5,2,2,3,0,0,0\r]
> Mar 22 10:30:11.93: [ 727]: --> [2:OK]
> Mar 22 10:30:11.93: [ 727]: <-- [19:AT+FLID="MORA_FAX"\r]
> Mar 22 10:30:12.04: [ 727]: --> [2:OK]
> Mar 22 10:30:12.05: [ 727]: <-- [13:ATDT01650912\r]
> Mar 22 10:30:28.70: [ 727]: --> [5:+FCON]
> Mar 22 10:30:28.70: [ 727]: --> [28:+FCSI:" 650912"]
> Mar 22 10:30:28.70: [ 727]: --> [21:+FDIS:1,3,0,2,3,2,0,0]
> Mar 22 10:30:28.70: [ 727]: --> [21:+FDIS:1,3,0,2,0,2,0,0]
> Mar 22 10:30:28.70: [ 727]: --> [2:OK]
> Mar 22 10:30:28.73: [ 727]: <-- [24:AT+FDIS=0,3,0,2,0,0,0,0\r]
> Mar 22 10:30:28.83: [ 727]: --> [2:OK]
> Mar 22 10:30:28.83: [ 727]: <-- [7:AT+FDT\r]
> Mar 22 10:30:35.00: [ 727]: --> [9:+FHNG:126]
> Mar 22 10:30:35.00: [ 727]: --> [2:OK]
> Mar 22 10:30:35.00: [ 727]: --> [10:NO CARRIER]
> Mar 22 10:30:35.00: [ 727]: MODEM No carrier
> Mar 22 10:30:35.00: [ 727]: SEND: Unknown hangup code; Giving up after 3
attempts to send same page "docq/doc3.ps;00", dirnum 0
> Mar 22 10:30:35.00: [ 727]: <-- [5:ATH0\r]
> Mar 22 10:30:35.11: [ 727]: --> [2:OK]
> Mar 22 10:30:35.11: [ 727]: MODEM set DTR OFF
> Mar 22 10:30:35.11: [ 727]: SESSION END
> 2. When I try to receive fax on ttyI interface it seems to be
>negotiating very
first communication with the sending fax machine, i.e. I can see the HylaFax
fax
id on sending fax machine. But after a little while the fax machine
disconnects
and at the same time the Linux server get STUCK. (This should not happen to
a
Linux machine!) I think there is something major wrong with ISDN card
drivers.
HylaFax Log follows.
> Mar 22 12:04:54.22: [ 612]: SESSION BEGIN 00000018 9474219124
> Mar 22 12:04:54.22: [ 612]: <-- [4:ATA\r]
>
> Thanks for any comments..
> Ruwan Jayanetti,
> University of Moratuwa.
> ______________________________________________________
> Listen to your favorite music while you work!
> - http://www.com/
>
--
_____________________________________________________________
Cytronics & Melware GbR
Weinbergstrasse 39
55296 Loerzweiler / Germany
fon: +49 6138 98 110-0
fax: +49 6138 98 110-9
http://www.melware.de
mailto:info@melware.de
_____________________________________________________________
_________________________________________________________________________
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com.
____________________ HylaFAX(tm) Users Mailing List _______________________
To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
