Re: [hylafax-users] spead

["Dan" <dwright@spca.org>]

> I've used RedHat 7, HylaFAX 4.1beta3, and a Cirrus Logic modem in Class 1
> to send about 50 faxes in as many minutes.
> 
> How many failures are you experiencing out of the 100?



very few if any mostly no carrier detected or busy signal
here is my modem config file I had problems setting it up
and from trial and error got this to work .

thanks for your help
Dan
 


#
# Generic Class 1 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:  1
AreaCode:  214
FAXNumber:  ""
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing:  0xFFF
SessionTracing:  0xFFF
RecvFileMode:  0666
LogFileMode:  0600
DeviceMode:  0600
RingsBeforeAnswer: 1
SpeakerVolume:  quiet
GettyArgs:  "-h %l dx_%s"
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:  Class1  # use this to supply a hint
ModemRate:  19200  # rate for DCE-DTE communication
ModemFlowControl: xonxoff  # XON/XOFF flow control assumed
#
#ModemSetupDTRCmd: AT&D2  # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1  # setup so DCD follows carrier
##GettyArgs:  "-h %l dx_%s" # modem must auto-detect fax/data
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd:  ATDT%s  # T for tone dialing, @ for silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
###ModemResetCmds:  ""  # stuff to do when modem is reset
ModemAnswerCmd:  ATA  # use this to answer phone
#ModemNoFlowCmd:  AT&K  # disable flow control cmd
#ModemHardFlowCmd: AT&K3  # hardware flow control cmd
ModemSoftFlowCmd: AT&K4  # software flow control cmd
ModemNoAutoAnswerCmd: ATS0=0  # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd: ATE0  # disable command echo
#ModemVerboseResultsCmd: ATV1  # enable verbose command results
#ModemResultCodesCmd: ATQ0  # enable result codes
#ModemOnHookCmd:  ATH0  # place phone on hook (hangup)
#ModemSoftResetCmd: ATZ  # do soft reset of modem
#ModemWaitTimeCmd: ATS7=60  # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd: ATS8=2  # comma pause time is 2 seconds
# ModemRecvFillOrder: LSB2MSB  # bit order of received facsimile
#ModemSendFillOrder: LSB2MSB  # bit order modem expects for transmit
#
Class1Cmd:  AT+FCLASS=1 # command to enter class 1
Class1TCFResponseDelay: 75  # 75ms delay between recv TCF & response
Class1SendPPMDelay: 75  # 75ms delay before sending PPM
Class1SendTCFDelay: 75  # 75ms delay between sending DCS & TCF
Class1TrainingRecovery: 1500  # 1.5sec delay after training failure
Class1RecvAbortOK: 200  # wait 200ms for abort response
Class1FrameOverhead: 4  # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer: 40000  # 35+5secs waiting for ident frames
Class1TCFMaxNonZero: 10  # max 10% of data may be non-zero
Class1TCFMinRun: 1000  # min run is 2/3rds of TCF duration




____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null