|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] MT5600ZDX and receive errors
RH 6.1 and
220 twgrh1 server (HylaFAX (tm) Version 4.1beta1) ready.
After increasing the
#SessionTracing: 11
SessionTracing: 0xFFF
I have received this error. Can these type of errors be reduced / eli,inated
by config changes?
Thanks!
ken
An attempt to receive facsimile on ttyS1 failed because:
COMREC invalid response received
---- Transcript of session follows ----
Mar 06 09:30:26.95: [ 647]: SESSION BEGIN 00002279 14254254867868
Mar 06 09:30:26.95: [ 647]: <-- [4:ATA\r]
Mar 06 09:30:35.64: [ 647]: --> [5:+FCON]
Mar 06 09:30:35.65: [ 647]: ANSWER: FAX CONNECTION
Mar 06 09:30:35.65: [ 647]: STATE CHANGE: ANSWERING -> RECEIVING
Mar 06 09:30:35.65: [ 647]: MODEM input buffering enabled
Mar 06 09:30:35.65: [ 647]: RECV FAX: begin
Mar 06 09:30:37.29: [ 647]: --> [29:+FTSI: " 8584968074"]
Mar 06 09:30:37.30: [ 647]: REMOTE TSI "8584968074"
Mar 06 09:30:37.59: [ 647]: --> [22:+FDCS: 0,5,0,2,0,0,0,0]
Mar 06 09:30:37.60: [ 647]: REMOTE wants 14400 bit/s
Mar 06 09:30:37.60: [ 647]: REMOTE wants page width 1728 pixels in 215 mm
Mar 06 09:30:37.60: [ 647]: REMOTE wants unlimited page length
Mar 06 09:30:37.60: [ 647]: REMOTE wants 3.85 line/mm
Mar 06 09:30:37.60: [ 647]: REMOTE wants 1-D MR
Mar 06 09:30:37.70: [ 647]: --> [2:OK]
Mar 06 09:30:37.71: [ 647]: <-- [7:AT+FDR\r]
Mar 06 09:30:40.70: [ 647]: --> [5:+FCFR]
Mar 06 09:30:42.86: [ 647]: --> [22:+FDCS: 0,5,0,2,0,0,0,0]
Mar 06 09:30:42.87: [ 647]: REMOTE wants 14400 bit/s
Mar 06 09:30:42.87: [ 647]: REMOTE wants page width 1728 pixels in 215 mm
Mar 06 09:30:42.87: [ 647]: REMOTE wants unlimited page length
Mar 06 09:30:42.87: [ 647]: REMOTE wants 3.85 line/mm
Mar 06 09:30:42.87: [ 647]: REMOTE wants 1-D MR
Mar 06 09:30:42.87: [ 647]: --> [7:CONNECT]
Mar 06 09:30:42.87: [ 647]: RECV: begin page
Mar 06 09:30:42.87: [ 647]: RECV: send trigger 022
Mar 06 09:31:00.60: [ 647]: RECV/CQ: Bad 1D pixel count, row 1090, got 0,
expected 1728
Mar 06 09:31:00.60: [ 647]: RECV/CQ: Bad 1D pixel count, row 1091, got 0,
expected 1728
Mar 06 09:31:00.60: [ 647]: RECV/CQ: Bad 1D pixel count, row 1092, got 0,
expected 1728
Mar 06 09:31:00.60: [ 647]: RECV/CQ: Bad 1D pixel count, row 1093, got 0,
expected 1728
Mar 06 09:31:00.60: [ 647]: RECV/CQ: Bad 1D pixel count, row 1094, got 0,
expected 1728
Mar 06 09:31:00.60: [ 647]: RECV/CQ: Adjusting for trailing noise (5 run)
Mar 06 09:31:00.60: [ 647]: RECV: 1090 total lines, 0 bad lines, 0
consecutive bad lines
Mar 06 09:31:00.60: [ 647]: --> [17:+FPTS: 1,2219,0,0]
Mar 06 09:31:02.02: [ 647]: --> [7:+FET: 0]
Mar 06 09:31:02.02: [ 647]: RECV recv MPS (more pages, same document)
Mar 06 09:31:02.13: [ 647]: --> [2:OK]
Mar 06 09:31:02.13: [ 647]: RECV send MCF (message confirmation)
Mar 06 09:31:02.13: [ 647]: RECV FAX (00002279): from 8584968074, page 1 in
0:25, INF, 3.85 line/mm, 1-D MR
Mar 06 09:31:02.13: [ 647]: <-- [7:AT+FDR\r]
Mar 06 09:31:04.20: [ 647]: --> [7:CONNECT]
Mar 06 09:31:04.20: [ 647]: RECV: begin page
Mar 06 09:31:04.20: [ 647]: RECV: send trigger 022
Mar 06 09:31:20.01: [ 647]: RECV/CQ: Bad 1D pixel count, row 1087, got 0,
expected 1728
Mar 06 09:31:20.01: [ 647]: RECV/CQ: Bad 1D pixel count, row 1088, got 0,
expected 1728
Mar 06 09:31:20.01: [ 647]: RECV/CQ: Bad 1D pixel count, row 1089, got 0,
expected 1728
Mar 06 09:31:20.01: [ 647]: RECV/CQ: Bad 1D pixel count, row 1090, got 0,
expected 1728
Mar 06 09:31:20.01: [ 647]: RECV/CQ: Bad 1D pixel count, row 1091, got 0,
expected 1728
Mar 06 09:31:20.01: [ 647]: RECV/CQ: Adjusting for trailing noise (5 run)
Mar 06 09:31:20.01: [ 647]: RECV: 1087 total lines, 0 bad lines, 0
consecutive bad lines
Mar 06 09:31:20.01: [ 647]: --> [17:+FPTS: 1,2219,0,0]
Mar 06 09:31:21.55: [ 647]: --> [7:+FET: 1]
Mar 06 09:31:21.55: [ 647]: RECV recv EOM (more documents)
Mar 06 09:31:21.66: [ 647]: --> [2:OK]
Mar 06 09:31:21.66: [ 647]: RECV send MCF (message confirmation)
Mar 06 09:31:21.66: [ 647]: RECV FAX (00002279): from 8584968074, page 2 in
0:19, INF, 3.85 line/mm, 1-D MR
Mar 06 09:31:21.66: [ 647]: RECV FAX (00002279): recvq/fax00312.tif from
8584968074, route to <unspecified>, 2 pages in 0:46
Mar 06 09:31:21.66: [ 647]: <-- [7:AT+FDR\r]
Mar 06 09:31:33.36: [ 647]: --> [29:+FTSI: " 8584968074"]
Mar 06 09:31:33.36: [ 647]: REMOTE TSI "8584968074"
Mar 06 09:31:38.94: [ 647]: --> [22:+FDCS: 0,5,0,2,0,0,0,0]
Mar 06 09:31:38.94: [ 647]: REMOTE wants 14400 bit/s
Mar 06 09:31:38.94: [ 647]: REMOTE wants page width 1728 pixels in 215 mm
Mar 06 09:31:38.94: [ 647]: REMOTE wants unlimited page length
Mar 06 09:31:38.94: [ 647]: REMOTE wants 3.85 line/mm
Mar 06 09:31:38.94: [ 647]: REMOTE wants 1-D MR
Mar 06 09:31:38.94: [ 647]: --> [7:CONNECT]
Mar 06 09:31:38.94: [ 647]: RECV: begin page
Mar 06 09:31:38.94: [ 647]: RECV: send trigger 022
Mar 06 09:31:58.26: [ 647]: RECV/CQ: Bad 1D pixel count, row 1089, got 0,
expected 1728
Mar 06 09:31:58.26: [ 647]: RECV/CQ: Bad 1D pixel count, row 1090, got 0,
expected 1728
Mar 06 09:31:58.26: [ 647]: RECV/CQ: Bad 1D pixel count, row 1091, got 0,
expected 1728
Mar 06 09:31:58.26: [ 647]: RECV/CQ: Bad 1D pixel count, row 1092, got 0,
expected 1728
Mar 06 09:31:58.26: [ 647]: RECV/CQ: Bad 1D pixel count, row 1093, got 0,
expected 1728
Mar 06 09:31:58.26: [ 647]: RECV/CQ: Adjusting for trailing noise (5 run)
Mar 06 09:31:58.26: [ 647]: RECV: 1089 total lines, 0 bad lines, 0
consecutive bad lines
Mar 06 09:31:58.26: [ 647]: --> [17:+FPTS: 1,2219,0,0]
Mar 06 09:31:59.68: [ 647]: --> [7:+FET: 0]
Mar 06 09:31:59.68: [ 647]: RECV recv MPS (more pages, same document)
Mar 06 09:31:59.79: [ 647]: --> [2:OK]
Mar 06 09:31:59.79: [ 647]: RECV send MCF (message confirmation)
Mar 06 09:31:59.79: [ 647]: RECV FAX (00002279): from 8584968074, page 1 in
0:38, INF, 3.85 line/mm, 1-D MR
Mar 06 09:31:59.79: [ 647]: <-- [7:AT+FDR\r]
Mar 06 09:32:01.84: [ 647]: --> [7:CONNECT]
Mar 06 09:32:01.84: [ 647]: RECV: begin page
Mar 06 09:32:01.84: [ 647]: RECV: send trigger 022
Mar 06 09:32:21.33: [ 647]: RECV/CQ: Bad 1D pixel count, row 1085, got 0,
expected 1728
Mar 06 09:32:21.33: [ 647]: RECV/CQ: Bad 1D pixel count, row 1086, got 0,
expected 1728
Mar 06 09:32:21.33: [ 647]: RECV/CQ: Bad 1D pixel count, row 1087, got 0,
expected 1728
Mar 06 09:32:21.33: [ 647]: RECV/CQ: Bad 1D pixel count, row 1088, got 0,
expected 1728
Mar 06 09:32:21.33: [ 647]: RECV/CQ: Bad 1D pixel count, row 1089, got 0,
expected 1728
Mar 06 09:32:21.33: [ 647]: RECV/CQ: Adjusting for trailing noise (5 run)
Mar 06 09:32:21.33: [ 647]: RECV: 1085 total lines, 0 bad lines, 0
consecutive bad lines
Mar 06 09:32:21.44: [ 647]: --> [17:+FPTS: 1,2219,0,0]
Mar 06 09:32:22.97: [ 647]: --> [7:+FET: 1]
Mar 06 09:32:22.97: [ 647]: RECV recv EOM (more documents)
Mar 06 09:32:23.08: [ 647]: --> [2:OK]
Mar 06 09:32:23.08: [ 647]: RECV send MCF (message confirmation)
Mar 06 09:32:23.08: [ 647]: RECV FAX (00002279): from 8584968074, page 2 in
0:24, INF, 3.85 line/mm, 1-D MR
Mar 06 09:32:23.08: [ 647]: RECV FAX (00002279): recvq/fax00314.tif from
8584968074, route to <unspecified>, 2 pages in 1:02
Mar 06 09:32:23.08: [ 647]: <-- [7:AT+FDR\r]
Mar 06 09:32:34.79: [ 647]: --> [29:+FTSI: " 8584968074"]
Mar 06 09:32:34.79: [ 647]: REMOTE TSI "8584968074"
Mar 06 09:32:40.36: [ 647]: --> [22:+FDCS: 0,5,0,2,0,0,0,0]
Mar 06 09:32:40.36: [ 647]: REMOTE wants 14400 bit/s
Mar 06 09:32:40.36: [ 647]: REMOTE wants page width 1728 pixels in 215 mm
Mar 06 09:32:40.36: [ 647]: REMOTE wants unlimited page length
Mar 06 09:32:40.36: [ 647]: REMOTE wants 3.85 line/mm
Mar 06 09:32:40.36: [ 647]: REMOTE wants 1-D MR
Mar 06 09:32:40.36: [ 647]: --> [7:CONNECT]
Mar 06 09:32:40.36: [ 647]: RECV: begin page
Mar 06 09:32:40.36: [ 647]: RECV: send trigger 022
Mar 06 09:32:50.32: [ 647]: RECV/CQ: Bad 1D pixel count, row 507, got 1788,
expected 1728
Mar 06 09:32:50.32: [ 647]: RECV/CQ: Adjusting for trailing noise (1 run)
Mar 06 09:32:50.32: [ 647]: RECV: 507 total lines, 0 bad lines, 0
consecutive bad lines
Mar 06 09:32:50.32: [ 647]: --> [17:+FPTS: 1,2219,0,0]
Mar 06 09:33:08.68: [ 647]: --> [10:+FHNG: 102]
Mar 06 09:33:08.68: [ 647]: REMOTE HANGUP: COMREC invalid response received
(code 102)
Mar 06 09:33:10.11: [ 647]: --> [2:OK]
Mar 06 09:33:10.11: [ 647]: RECV FAX (00002279): recvq/fax00315.tif from
8584968074, route to <unspecified>, 0 pages in 0:47
Mar 06 09:33:10.11: [ 647]: RECV FAX: COMREC invalid response received
Mar 06 09:33:10.11: [ 647]: RECV FAX: bin/faxrcvd "recvq/fax00312.tif"
"ttyS1" "00002279" ""
Mar 06 09:33:12.82: [ 647]: RECV FAX: bin/faxrcvd "recvq/fax00314.tif"
"ttyS1" "00002279" ""
Mar 06 09:33:16.51: [ 647]: RECV FAX (00002279): session with 8584968074
terminated abnormally: COMREC invalid response received
Mar 06 09:33:16.51: [ 647]: RECV FAX: bin/faxrcvd "recvq/fax00315.tif"
"ttyS1" "00002279" "COMREC invalid response received"
> -----Original Message-----
> From: Abrahamsen, Kenneth
> Sent: Monday, March 05, 2001 10:02 AM
> To: hylafax-users@hylafax.org
> Subject: MT5600ZDX and receive errors
>
> I've put a MT5600ZDX into production a few days ago and have been getting
> these type of errors. Many faxes are received properly but some like this
> have a problem. Have I made errors in the config file or left something
> out?
> Thanks.
> ken
>
> Config file.....
>
> # $Id: mt-5600zdx 2001/02/21 12:00:00 root Exp $
> #
> # HylaFAX Facsimile Software
> #
> # Copyright (c) 1990-1996 Sam Leffler
> # Copyright (c) 1991-1996 Silicon Graphics, Inc.
> # HylaFAX is a trademark of Silicon Graphics, Inc.
> #
> # Permission to use, copy, modify, distribute, and sell this software and
> # its documentation for any purpose is hereby granted without fee,
> provided
> # that (i) the above copyright notices and this permission notice appear
> in
> # all copies of the software and related documentation, and (ii) the names
> of
> # Sam Leffler and Silicon Graphics may not be used in any advertising or
> # publicity relating to the software without the specific, prior written
> # permission of Sam Leffler and Silicon Graphics.
> #
> # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
> # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
> # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
> #
> # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
> # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
> # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
> # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY
> OF
> # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
> # OF THIS SOFTWARE.
> #
> #
> # Configuration for a Multitech 5600ZDX Class 2 modem.
> #
> # This configuration file sets up the modem to run at 38.4 for
> # sending and for receiving. RTS/CTS is used for flow control
> # which also works for data connections. Adaptive answer support
> # is reliable, but to use it you must also enable ModemWaitForConnect
> # to force the server to skip intermediate status messages and
> # wait for the "CONNECT" message.
> #
> # CONFIG: CLASS2: MULTITECH 5600ZDX
> #
> # BEGIN-SERVER
> # END-SERVER
> CountryCode: 1
> AreaCode: 425
> FAXNumber: 425-486-7868
> LongDistancePrefix: 1
> InternationalPrefix: 011
> DialStringRules: etc/dialrules
> ServerTracing: 1
> SessionTracing: 11
> RecvFileMode: 0644
> LogFileMode: 0644
> DeviceMode: 0600
> RingsBeforeAnswer: 1
> SpeakerVolume: off
> GettyArgs: "-h %l dx_%s"
> LocalIdentifier: "425-486-7868 (WRIGHT GROUP)"
> TagLineFont: etc/lutRS18.pcf
> TagLineFormat: "From %%l|%c - Job %i|Page %%p of %%t"
> MaxRecvPages: 9999
> #
> # Modem-related stuff: should reflect modem command interface
> # and hardware connection/cabling (e.g. flow control).
> #
> ModemType: Class2 # use class 2 interface
> ModemRate: 38400 # lock rate for DCE-DTE
> # communication
> ModemFlowControl: rtscts # default
> #
> ModemHardFlowCmd: AT&E4 # hardware flow control
> ModemSoftFlowCmd: AT&E5 # software flow control
> ModemSetupDTRCmd: AT&D3 # setup so DTR drop resets
> # modem
> ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier
> # (or not)
> ModemSetupAACmd: AT+FAA=1 # enable adaptive-answer in
> # class 2
> #
> # NB: some models get confused by the @
> #
> ModemDialCmd: ATDT%s # T for tone dialing, @ for
> # silence
> #
> ModemSendFillOrder: LSB2MSB # as expected
> ModemRecvFillOrder: MSB2LSB # opposite of what makes sense
> Class2RecvDataTrigger: "\022" # character sent to modem to
> # start recv
>
>
> ===================================================================
> ERROR Message....
> An attempt to receive facsimile on ttyS1 failed because:
>
> Normal and proper end of connection
>
> ---- Transcript of session follows ----
>
> Mar 05 09:51:40.45: [ 647]: SESSION BEGIN 00002223 14254254867868
> Mar 05 09:51:40.45: [ 647]: <-- [4:ATA\r]
> Mar 05 09:51:49.03: [ 647]: --> [5:+FCON]
> Mar 05 09:51:49.03: [ 647]: ANSWER: FAX CONNECTION
> Mar 05 09:51:49.03: [ 647]: RECV FAX: begin
> Mar 05 09:51:50.65: [ 647]: --> [29:+FTSI: " FIOT4.24 "]
> Mar 05 09:51:50.65: [ 647]: REMOTE TSI "FIOT4.24"
> Mar 05 09:51:51.05: [ 647]: --> [22:+FDCS: 0,5,0,2,0,0,0,0]
> Mar 05 09:51:51.05: [ 647]: REMOTE wants 14400 bit/s
> Mar 05 09:51:51.05: [ 647]: REMOTE wants page width 1728 pixels in 215 mm
> Mar 05 09:51:51.05: [ 647]: REMOTE wants unlimited page length
> Mar 05 09:51:51.05: [ 647]: REMOTE wants 3.85 line/mm
> Mar 05 09:51:51.05: [ 647]: REMOTE wants 1-D MR
> Mar 05 09:51:51.05: [ 647]: --> [2:OK]
> Mar 05 09:51:51.05: [ 647]: <-- [7:AT+FDR\r]
> Mar 05 09:51:54.04: [ 647]: --> [5:+FCFR]
> Mar 05 09:51:56.26: [ 647]: --> [22:+FDCS: 0,5,0,2,0,0,0,0]
> Mar 05 09:51:56.26: [ 647]: REMOTE wants 14400 bit/s
> Mar 05 09:51:56.26: [ 647]: REMOTE wants page width 1728 pixels in 215 mm
> Mar 05 09:51:56.26: [ 647]: REMOTE wants unlimited page length
> Mar 05 09:51:56.26: [ 647]: REMOTE wants 3.85 line/mm
> Mar 05 09:51:56.26: [ 647]: REMOTE wants 1-D MR
> Mar 05 09:51:56.26: [ 647]: --> [7:CONNECT]
> Mar 05 09:51:56.26: [ 647]: RECV: begin page
> Mar 05 09:51:56.26: [ 647]: RECV: send trigger 022
> Mar 05 09:52:17.27: [ 647]: RECV: 955 total lines, 0 bad lines, 0
> consecutive bad lines
> Mar 05 09:52:17.27: [ 647]: --> [17:+FPTS: 1,2219,0,0]
> Mar 05 09:52:18.50: [ 647]: --> [8:+FHNG: 0]
> Mar 05 09:52:18.50: [ 647]: REMOTE HANGUP: Normal and proper end of
> connection (code 0)
> Mar 05 09:52:19.93: [ 647]: --> [2:OK]
> Mar 05 09:52:19.93: [ 647]: RECV recv MPS (more pages, same document)
> Mar 05 09:52:49.93: [ 647]: MODEM <Timeout>
> Mar 05 09:52:49.93: [ 647]: RECV FAX (00002223): recvq/fax00258.tif from
> FIOT4.24, route to <unspecified>, 0 pages in 1:00
> Mar 05 09:52:49.93: [ 647]: RECV FAX: Normal and proper end of connection
> Mar 05 09:52:49.93: [ 647]: RECV FAX (00002223): session with FIOT4.24
> terminated abnormally: Normal and proper end of connection
> Mar 05 09:52:49.93: [ 647]: RECV FAX: bin/faxrcvd "recvq/fax00258.tif"
> "ttyS1" "00002223" "Normal and proper end of connection"
____________________ HylaFAX(tm) Users Mailing List _______________________
To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
