[hylafax-users] Fax not received T.30 T2 Timeout ?

["Mark Welborn" <markw@electromotor.com>]

Hello,

 

HylaFAX was trying to receive a fax and failed.  I looked at the message log and the log indicates that the Training failed three times, before Training succeeded.  When Training was successful the rest of the log looked like this:

-----------------------------------------------------------------------------------------

 

Dec 18 08:50:16.46: [  757]: REMOTE wants 12000 bit/s
Dec 18 08:50:16.46: [  757]: REMOTE wants page width 1728 pixels in 215 mm
Dec 18 08:50:16.46: [  757]: REMOTE wants unlimited page length
Dec 18 08:50:16.46: [  757]: REMOTE wants 3.85 line/mm
Dec 18 08:50:16.46: [  757]: REMOTE wants 2-D MR
Dec 18 08:50:16.46: [  757]: RECV training at v.17 12000 bit/s
Dec 18 08:50:16.46: [  757]: <-- [11:AT+FRM=121\r]
Dec 18 08:50:18.20: [  757]: --> [7:CONNECT]
Dec 18 08:50:19.76: [  757]: RECV: TCF 2343 bytes, 2% non-zero, 2274 zero-run
Dec 18 08:50:19.77: [  757]: --> [10:NO CARRIER]
Dec 18 08:50:19.77: [  757]: DELAY 75 ms
Dec 18 08:50:19.85: [  757]: <-- [9:AT+FTH=3\r]
Dec 18 08:50:20.05: [  757]: --> [7:CONNECT]
Dec 18 08:50:20.05: [  757]: <-- data [3]
Dec 18 08:50:20.05: [  757]: <-- data [2]
Dec 18 08:50:21.22: [  757]: --> [2:OK]
Dec 18 08:50:21.22: [  757]: TRAINING succeeded
Dec 18 08:50:21.22: [  757]: <-- [11:AT+FRM=122\r]
Dec 18 08:50:22.23: [  757]: --> [7:CONNECT]
Dec 18 08:50:22.23: [  757]: RECV: begin page
Dec 18 08:50:24.28: [  757]: RECV: 105 total lines, 0 bad lines, 0 consecutive bad lines
Dec 18 08:50:24.28: [  757]: RECV: end page
Dec 18 08:50:24.28: [  757]: --> [10:NO CARRIER]
Dec 18 08:50:24.28: [  757]: <-- [9:AT+FRH=3\r]
Dec 18 08:50:31.37: [  757]: --> [7:CONNECT]
Dec 18 08:50:36.37: [  757]: <-- data [1]
Dec 18 08:50:36.57: [  757]: MODEM <Timeout>
Dec 18 08:50:36.57: [  757]: RECV FAX (00000178): recvq/fax00088.tif from , route to <unspecified>, 0 pages in 0:43
Dec 18 08:50:36.57: [  757]: RECV FAX: T.30 T2 timeout, expected page not received
Dec 18 08:50:36.57: [  757]: <-- [9:AT+FTH=3\r]
Dec 18 08:50:36.77: [  757]: --> [7:CONNECT]
Dec 18 08:50:36.77: [  757]: <-- data [3]
Dec 18 08:50:36.77: [  757]: <-- data [2]
Dec 18 08:50:37.95: [  757]: --> [2:OK]
Dec 18 08:50:37.95: [  757]: RECV FAX (00000178): session with  terminated abnormally: T.30 T2 timeout, expected page not received
Dec 18 08:50:37.95: [  757]: RECV FAX: bin/faxrcvd "recvq/fax00088.tif" "ttyS0" "00000178" "T.30 T2 timeout, expected page not received"

---------------------------------------------------------------------------------------------------

 

At the end of this log, what does the "T.30 T2 timeout" mean ?

Is this a problem on my HylaFAX server or was this a problem with the sending fax machine ?

 

Any comments are welcome.

 

Thanks,

 

Mark Welborn