|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Another no response to MPS code 52
Greetings List,
I have hylafax rpm (based on hylafax-cvs-20000604) running on redhat linux
6.2 with linux-2.2.17. Everything has gone well for the last couple of
months since we switched from a Hayes Acura 56K internal to a Multitech
MT5634ZPXi internal (for testing). At least until the multi met a
Panasonic KXFP250 fax machine :-)
I've created a config file going by the faq and what experience I have
with past configurations, tried xonxoff/crtscts and high and low speed DTE
rates with no success in making a fax go through the Panasonic. One in
twelve faxes make it past the first page but then die.. This is the first
failure I've had with the modem - it has sent to over 30 differant offices
without problem...
Looking through the archives, the best (common) answer I have found is "it
could be many things that cause MPS failure"... Is there any one document
that describes the possibile causes of a MPS failure so I could go down a
check list of probable causes??
Here is the important part of my config file:
==cut===
ModemType: Class2 # use this to supply a hint
ModemRate: 38400 # max rate for DCE-DTE communication
ModemFlowControl: rtscts # Hardware flow control assumed
#
ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
ModemRecvFillOrder: MSB2LSB # bit order of received facsimile
ModemHardFlowCmd: AT&K3 # enable hardware flow control
Class2HFLOCmd: AT+FLO=2 # fax class 2 hardware flow control
==cut==
and here is a log from the last attempt...
===cut===
Dec 06 09:51:03.65: [ 924]: SESSION BEGIN 00000592 19005551213
Dec 06 09:51:03.65: [ 924]: SEND FAX: JOB 304 DEST 1-900-555-1213 COMMID 00000592
Dec 06 09:51:03.65: [ 924]: DELAY 2600 ms
Dec 06 09:51:06.25: [ 924]: <-- [4:ATZ\r]
Dec 06 09:51:06.73: [ 924]: --> [171:ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ]
Dec 06 09:51:06.73: [ 924]: --> [2:OK]
Dec 06 09:51:06.73: [ 924]: <-- [15:ATE0V1Q0S0=0H0\r]
Dec 06 09:51:06.76: [ 924]: --> [14:ATE0V1Q0S0=0H0]
Dec 06 09:51:06.76: [ 924]: --> [2:OK]
Dec 06 09:51:06.76: [ 924]: <-- [15:ATS8=2S7=60&K3\r]
Dec 06 09:51:06.77: [ 924]: --> [2:OK]
Dec 06 09:51:06.77: [ 924]: <-- [12:AT+FCLASS=2\r]
Dec 06 09:51:06.78: [ 924]: --> [2:OK]
Dec 06 09:51:06.78: [ 924]: <-- [9:AT+FLO=2\r]
Dec 06 09:51:06.79: [ 924]: --> [2:OK]
Dec 06 09:51:06.79: [ 924]: <-- [10:AT+FTBC=0\r]
Dec 06 09:51:06.80: [ 924]: --> [2:OK]
Dec 06 09:51:06.80: [ 924]: <-- [10:AT+FBOR=0\r]
Dec 06 09:51:06.81: [ 924]: --> [2:OK]
Dec 06 09:51:06.81: [ 924]: <-- [13:AT+FPHCTO=30\r]
Dec 06 09:51:06.82: [ 924]: --> [2:OK]
Dec 06 09:51:06.82: [ 924]: <-- [24:AT+FDCC=1,5,0,2,0,0,0,0\r]
Dec 06 09:51:06.83: [ 924]: --> [2:OK]
Dec 06 09:51:06.83: [ 924]: <-- [7:ATL3M1\r]
Dec 06 09:51:06.84: [ 924]: --> [2:OK]
Dec 06 09:51:06.84: [ 924]: <-- [12:AT+FCLASS=2\r]
Dec 06 09:51:06.95: [ 924]: --> [2:OK]
Dec 06 09:51:06.95: [ 924]: <-- [9:AT+FLO=2\r]
Dec 06 09:51:07.06: [ 924]: --> [2:OK]
Dec 06 09:51:07.06: [ 924]: <-- [10:AT+FTBC=0\r]
Dec 06 09:51:07.17: [ 924]: --> [2:OK]
Dec 06 09:51:07.17: [ 924]: <-- [10:AT+FBOR=0\r]
Dec 06 09:51:07.28: [ 924]: --> [2:OK]
Dec 06 09:51:07.28: [ 924]: <-- [13:AT+FPHCTO=30\r]
Dec 06 09:51:07.39: [ 924]: --> [2:OK]
Dec 06 09:51:07.39: [ 924]: <-- [24:AT+FDCC=1,5,0,2,0,0,0,0\r]
Dec 06 09:51:07.50: [ 924]: --> [2:OK]
Dec 06 09:51:07.50: [ 924]: <-- [21:AT+FLID="9005551212"\r]
Dec 06 09:51:07.61: [ 924]: --> [2:OK]
Dec 06 09:51:07.61: [ 924]: DIAL 19005551213
Dec 06 09:51:07.61: [ 924]: <-- [16:ATDT19005551213\r]
Dec 06 09:51:20.26: [ 924]: --> [5:+FCON]
Dec 06 09:51:20.26: [ 924]: --> [47:+FNSF:0,0,14,0,0,0,22,15,1,3,0,16,0,2,149,128,8]
Dec 06 09:51:20.26: [ 924]: REMOTE NSF "0,0,14,0,0,0,22,15,1,3,0,16,0,2,149,128,8"
Dec 06 09:51:20.26: [ 924]: NSF remote fax equipment: unknown
Dec 06 09:51:21.01: [ 924]: --> [28:+FCSI:" "]
Dec 06 09:51:21.01: [ 924]: REMOTE CSI ""
Dec 06 09:51:21.39: [ 924]: --> [21:+FDIS:1,3,0,2,0,0,0,5]
Dec 06 09:51:21.39: [ 924]: --> [2:OK]
Dec 06 09:51:21.39: [ 924]: REMOTE best rate 9600 bit/s
Dec 06 09:51:21.39: [ 924]: REMOTE max page width 1728 pixels in 215 mm
Dec 06 09:51:21.39: [ 924]: REMOTE max unlimited page length
Dec 06 09:51:21.39: [ 924]: REMOTE best vres 7.7 line/mm
Dec 06 09:51:21.39: [ 924]: REMOTE best format 1-D MR
Dec 06 09:51:21.39: [ 924]: REMOTE best 20 ms/scanline
Dec 06 09:51:21.39: [ 924]: USE 9600 bit/s
Dec 06 09:51:21.39: [ 924]: USE 20 ms/scanline
Dec 06 09:51:21.39: [ 924]: SEND file "docq/doc304.cover;31"
Dec 06 09:51:21.39: [ 924]: USE page width 1728 pixels in 215 mm
Dec 06 09:51:21.39: [ 924]: USE unlimited page length
Dec 06 09:51:21.39: [ 924]: USE 7.7 line/mm
Dec 06 09:51:21.39: [ 924]: USE 1-D MR
Dec 06 09:51:21.39: [ 924]: <-- [24:AT+FDIS=1,3,0,2,0,0,0,5\r]
Dec 06 09:51:21.50: [ 924]: --> [2:OK]
Dec 06 09:51:21.50: [ 924]: <-- [7:AT+FDT\r]
Dec 06 09:51:27.10: [ 924]: --> [21:+FDCS:1,3,0,2,0,0,0,5]
Dec 06 09:51:27.21: [ 924]: --> [7:CONNECT]
Dec 06 09:51:27.21: [ 924]: SEND wait for XON
Dec 06 09:51:27.21: [ 924]: --> [1:]
Dec 06 09:51:27.21: [ 924]: SEND begin page
Dec 06 09:51:27.22: [ 924]: <-- data [1028]
(lots of data lines cut!)
Dec 06 09:52:18.78: [ 924]: <-- data [1025]
Dec 06 09:52:19.62: [ 924]: <-- data [510]
Dec 06 09:52:20.10: [ 924]: SENT 43518 bytes of data
Dec 06 09:52:20.10: [ 924]: <-- data [2]
Dec 06 09:52:20.10: [ 924]: SEND end page
Dec 06 09:52:30.61: [ 924]: --> [2:OK]
Dec 06 09:52:30.61: [ 924]: SEND send MPS (more pages, same document)
Dec 06 09:52:30.61: [ 924]: <-- [9:AT+FET=0\r]
Dec 06 09:52:45.47: [ 924]: --> [8:+FHNG:52]
Dec 06 09:52:45.47: [ 924]: REMOTE HANGUP: No response to MPS repeated 3 times (code 52)
Dec 06 09:52:45.47: [ 924]: <-- [5:ATH0\r]
Dec 06 09:52:46.51: [ 924]: --> [2:OK]
Dec 06 09:52:46.51: [ 924]: SESSION END
==cut==
One thing that is weird is after the ATZ the modem responds with a bunch
of junk characters - not sure what causes that but I've seen it only with
this model of modem... and it doesn't seem to be a problem on other calls.
Any help will be greatly appreciated!!
Andrew McRory - President/CTO amacc@iron-bridge.net *****************
The PC Doctor, Inc. www.pcdr.com 850-575-7213 **
Iron Bridge Communications, Inc. www.iron-bridge.net 850-575-0779 **
Contributed RPMS for RedHat and Caldera ftp://ftp.iron-bridge.net/pub **
****************************************************************************
____________________ HylaFAX(tm) Users Mailing List _______________________
To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
