[hylafax-users] EOP Error / Re: Busy signal detected

["Sven Johannsen" <sven.johannsen@menck-fenster.de>]

Thanks for all the help,

with the ATX3DT0 dial command, my Zyxel U-1496EG works on the branch
line.

But now I've got another problem. Hylafax didn't stop sending the first
page until 3 attempts. I found an entry in the SuSE Supportdatabase,
which said that this happens when the opposite is a DIN A4 Fax. Then it
sends an receiving error and hylafax try's to send the first page again.
The suggested solution was to change the following parameters in the
config.modem file:

Class2PHCTOCmd:     AT+FPHCTO=FF    # set phase C timeout parameter
Class2DCCQueryCmd:  "!(0,1),(0-5),(0-4),(0),(0,1),(0),(0),(0-7)"

but this didn't help. Here is a part of a job-session-protocol:

Your facsimile job to 76010685 was not sent because:     # of course it
was sent, 3 times!!!
    Unable to transmit page (giving up after 3 attempts)

The job will be retried at 14:07.

    ---- Transcript of session follows ----


[cut]
Nov 23 14:00:02.54: [11454]: <-- [9:AT+FBO=0\r]
Nov 23 14:00:02.65: [11454]: --> [2:OK]
Nov 23 14:00:02.65: [11454]: <-- [13:AT+FPHCTO=FF\r]
Nov 23 14:00:02.76: [11454]: --> [2:OK]
Nov 23 14:00:02.76: [11454]: <-- [15:AT+FNR=1,1,1,1\r]
Nov 23 14:00:02.87: [11454]: --> [2:OK]
Nov 23 14:00:02.87: [11454]: <-- [9:AT+FIE=0\r]
Nov 23 14:00:02.98: [11454]: --> [2:OK]
Nov 23 14:00:02.98: [11454]: <-- [23:AT+FCC=1,5,2,0,1,0,0,0\r]
Nov 23 14:00:03.10: [11454]: --> [2:OK]
Nov 23 14:00:03.10: [11454]: <-- [28:AT+FLI="Menck Fenster GmbH"\r]
Nov 23 14:00:03.22: [11454]: --> [2:OK]
Nov 23 14:00:03.23: [11454]: DIAL 76010685
Nov 23 14:00:03.23: [11454]: <-- [16:ATX3DT076010685\r]
Nov 23 14:00:50.00: [11454]: --> [4:+FCO]
Nov 23 14:00:50.14: [11454]: --> [126:+FNF:00 00 11 80 00 86 49 10 4D 65
6E 63 6B 20 46 65 6E 73 74 65 72 20 20 20 00 3A 00 82 04 30 30 30 30 80
C0 0E 01 01 01 01  ]
Nov 23 14:00:50.14: [11454]: REMOTE NSF "00 00 11 80 00 86 49 10 4D 65
6E 63 6B 20 46 65 6E 73 74 65 72 20 20 20 00 3A 00 82 04 30 30 30 30 80
C0 0E 01 01 01 01"
Nov 23 14:00:50.14: [11454]: --> [26:+FCI:       +494076010685 ]
Nov 23 14:00:50.14: [11454]: REMOTE CSI "+494076010685"
Nov 23 14:00:50.14: [11454]: --> [20:+FIS:1,3,0,2,1,0,0,2]
Nov 23 14:00:50.14: [11454]: --> [2:OK]
Nov 23 14:00:50.14: [11454]: REMOTE best rate 9600 bit/s
Nov 23 14:00:50.14: [11454]: REMOTE max page width 1728 pixels in 215 mm
Nov 23 14:00:50.14: [11454]: REMOTE max unlimited page length
Nov 23 14:00:50.14: [11454]: REMOTE best vres 7.7 line/mm
Nov 23 14:00:50.14: [11454]: REMOTE best format 2-D MR
Nov 23 14:00:50.14: [11454]: REMOTE best 10 ms, 5 ms/scanline
Nov 23 14:00:50.14: [11454]: USE 9600 bit/s
Nov 23 14:00:50.14: [11454]: USE 10 ms, 5 ms/scanline
Nov 23 14:00:50.14: [11454]: SEND file "docq/doc18.ps;00"
Nov 23 14:00:50.14: [11454]: USE page width 1728 pixels in 215 mm
Nov 23 14:00:50.14: [11454]: USE unlimited page length
Nov 23 14:00:50.14: [11454]: USE 3.85 line/mm
Nov 23 14:00:50.14: [11454]: USE 1-D MR
Nov 23 14:00:50.14: [11454]: <-- [23:AT+FIS=0,3,0,2,0,0,0,2\r]
Nov 23 14:00:50.26: [11454]: --> [2:OK]
Nov 23 14:00:50.26: [11454]: <-- [7:AT+FDT\r]
Nov 23 14:00:55.96: [11454]: --> [20:+FCS:0,3,0,2,0,0,0,2]
Nov 23 14:00:55.96: [11454]: --> [7:CONNECT]
Nov 23 14:00:55.96: [11454]: SEND begin page
Nov 23 14:01:07.28: [11454]: SENT 14683 bytes of data
Nov 23 14:01:07.28: [11454]: SEND 1D RTC
Nov 23 14:01:07.28: [11454]: SEND end page
Nov 23 14:01:07.28: [11454]: SEND send EOP (no more pages or documents)
Nov 23 14:01:17.48: [11454]: --> [5:ERROR]
Nov 23 14:01:17.48: [11454]: SEND recv RTN (retrain negative)
Nov 23 14:01:17.48: [11454]: <-- [23:AT+FIS=0,2,0,2,0,0,0,2\r]
Nov 23 14:01:17.60: [11454]: --> [2:OK]

[cut]

What can I do? Any ideas?

 Sven




____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null