|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] USR: ok class2.0, error in class1 (HylaFAX <-> HylaFAX)
There is one server (Linux RedHat 6.1, kernel 2.2.16) with the latest HylaFAX cvs installed.
It has 2 modems attached and controlled by HylaFAX:
1) USRobotics Courier HST Dual Standard V.34 Fax.
More details at the end.
2) Rockwell based class1 fax-modem
I configured the USR in 2 ways using faxaddmodem:
a) class2.0 rtscts
b) class1 xonxoff (since I read class1 is more reliable for USR).
when sending a fax from 1 to 2:
- if the USR is class2.0 then the fax is received well
- if the USR is class1 then the fax is aborted.
== USR class2.0/rtscts sending
Nov 17 19:59:47.83: [10109]: SESSION BEGIN 00003958 39019RECVNO
Nov 17 19:59:47.83: [10109]: SEND FAX: JOB 2046 DEST 019RECVNO COMMID 00003958
Nov 17 19:59:47.83: [10109]: MODEM set DTR OFF
Nov 17 19:59:47.83: [10109]: DELAY 2600 ms
Nov 17 19:59:50.42: [10109]: MODEM set DTR ON
Nov 17 19:59:50.42: [10109]: MODEM set baud rate: 19200 baud, input flow RTS/CTS, output flow
RTS/CTS
Nov 17 19:59:50.42: [10109]: MODEM flush i/o
Nov 17 19:59:50.42: [10109]: <-- [4:ATZ\r]
Nov 17 19:59:50.73: [10109]: --> [3:ATZ]
Nov 17 19:59:50.73: [10109]: --> [2:OK]
Nov 17 19:59:50.73: [10109]: <-- [17:ATE0V1Q0X3S0=0H0\r]
Nov 17 19:59:50.91: [10109]: --> [16:ATE0V1Q0X3S0=0H0]
Nov 17 19:59:50.91: [10109]: --> [2:OK]
Nov 17 19:59:50.91: [10109]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=1&D2&C1\r]
Nov 17 19:59:51.09: [10109]: --> [2:OK]
Nov 17 19:59:51.09: [10109]: <-- [14:AT+FCLASS=2.0\r]
Nov 17 19:59:51.14: [10109]: --> [2:OK]
Nov 17 19:59:51.14: [10109]: <-- [9:AT+FLO=2\r]
Nov 17 19:59:51.19: [10109]: --> [2:OK]
Nov 17 19:59:51.19: [10109]: <-- [9:AT+FPP=0\r]
Nov 17 19:59:51.24: [10109]: --> [2:OK]
Nov 17 19:59:51.24: [10109]: <-- [9:AT+FBO=0\r]
Nov 17 19:59:51.29: [10109]: --> [2:OK]
Nov 17 19:59:51.29: [10109]: <-- [10:AT+FCT=30\r]
Nov 17 19:59:51.34: [10109]: --> [2:OK]
Nov 17 19:59:51.34: [10109]: <-- [15:AT+FNR=1,1,1,0\r]
Nov 17 19:59:51.39: [10109]: --> [2:OK]
Nov 17 19:59:51.39: [10109]: <-- [9:AT+FIE=0\r]
Nov 17 19:59:51.44: [10109]: --> [2:OK]
Nov 17 19:59:51.44: [10109]: <-- [9:AT+FBU=0\r]
Nov 17 19:59:51.49: [10109]: --> [2:OK]
Nov 17 19:59:51.49: [10109]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Nov 17 19:59:51.55: [10109]: --> [2:OK]
Nov 17 19:59:51.55: [10109]: <-- [5:ATM0\r]
Nov 17 19:59:51.72: [10109]: --> [2:OK]
Nov 17 19:59:51.72: [10109]: STATE CHANGE: RUNNING -> SENDING
Nov 17 19:59:51.72: [10109]: MODEM input buffering enabled
Nov 17 19:59:51.72: [10109]: <-- [14:AT+FCLASS=2.0\r]
Nov 17 19:59:51.87: [10109]: --> [2:OK]
Nov 17 19:59:51.87: [10109]: <-- [9:AT+FLO=2\r]
Nov 17 19:59:52.02: [10109]: --> [2:OK]
Nov 17 19:59:52.02: [10109]: <-- [9:AT+FPP=0\r]
Nov 17 19:59:52.17: [10109]: --> [2:OK]
Nov 17 19:59:52.17: [10109]: <-- [9:AT+FBO=0\r]
Nov 17 19:59:52.32: [10109]: --> [2:OK]
Nov 17 19:59:52.32: [10109]: <-- [10:AT+FCT=30\r]
Nov 17 19:59:52.47: [10109]: --> [2:OK]
Nov 17 19:59:52.47: [10109]: <-- [15:AT+FNR=1,1,1,0\r]
Nov 17 19:59:52.62: [10109]: --> [2:OK]
Nov 17 19:59:52.62: [10109]: <-- [9:AT+FIE=0\r]
Nov 17 19:59:52.77: [10109]: --> [2:OK]
Nov 17 19:59:52.77: [10109]: <-- [9:AT+FBU=0\r]
Nov 17 19:59:52.92: [10109]: --> [2:OK]
Nov 17 19:59:52.92: [10109]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Nov 17 19:59:53.08: [10109]: --> [2:OK]
Nov 17 19:59:53.08: [10109]: <-- [26:AT+FLI="+39 06 123456789"\r]
Nov 17 19:59:53.24: [10109]: --> [2:OK]
Nov 17 19:59:53.24: [10109]: DIAL 019RECVNO
Nov 17 19:59:53.24: [10109]: <-- [14:ATDT019RECVNO\r]
Nov 17 20:00:06.72: [10109]: --> [4:+FCO]
Nov 17 20:00:08.42: [10109]: --> [27:+FCI:" +39 019 RECVNO"]
Nov 17 20:00:08.42: [10109]: REMOTE CSI "+39 019 RECVNO"
Nov 17 20:00:08.90: [10109]: --> [20:+FIS:1,5,2,2,1,0,0,0]
Nov 17 20:00:09.01: [10109]: --> [2:OK]
Nov 17 20:00:09.01: [10109]: REMOTE best rate 14400 bit/s
Nov 17 20:00:09.01: [10109]: REMOTE max page width 2432 pixels in 303 mm
Nov 17 20:00:09.01: [10109]: REMOTE max unlimited page length
Nov 17 20:00:09.01: [10109]: REMOTE best vres 7.7 line/mm
Nov 17 20:00:09.01: [10109]: REMOTE best format 2-D MR
Nov 17 20:00:09.01: [10109]: REMOTE best 0 ms/scanline
Nov 17 20:00:09.01: [10109]: USE 14400 bit/s
Nov 17 20:00:09.01: [10109]: USE 0 ms/scanline
Nov 17 20:00:09.01: [10109]: SEND file "docq/doc2062.ps;01"
Nov 17 20:00:09.01: [10109]: USE page width 1728 pixels in 215 mm
Nov 17 20:00:09.01: [10109]: USE unlimited page length
Nov 17 20:00:09.01: [10109]: USE 7.7 line/mm
Nov 17 20:00:09.01: [10109]: USE 1-D MR
Nov 17 20:00:09.01: [10109]: <-- [23:AT+FIS=1,5,0,2,0,0,0,0\r]
Nov 17 20:00:09.17: [10109]: --> [2:OK]
Nov 17 20:00:09.17: [10109]: <-- [7:AT+FDT\r]
Nov 17 20:00:09.33: [10109]: --> [20:+FCS:1,5,0,2,0,0,0,0]
Nov 17 20:00:16.37: [10109]: --> [7:CONNECT]
Nov 17 20:00:16.37: [10109]: SEND begin page
Nov 17 20:00:16.37: [10109]: <-- data [1026]
Nov 17 20:00:16.37: [10109]: <-- data [1025]
Nov 17 20:00:16.37: [10109]: <-- data [1024]
Nov 17 20:00:16.37: [10109]: <-- data [1026]
Nov 17 20:00:16.37: [10109]: <-- data [1029]
Nov 17 20:00:18.37: [10109]: <-- data [1031]
Nov 17 20:00:18.37: [10109]: <-- data [1033]
Nov 17 20:00:18.37: [10109]: <-- data [1025]
Nov 17 20:00:20.37: [10109]: <-- data [1024]
Nov 17 20:00:20.37: [10109]: <-- data [1040]
Nov 17 20:00:20.37: [10109]: <-- data [1040]
Nov 17 20:00:20.37: [10109]: <-- data [1024]
Nov 17 20:00:22.36: [10109]: <-- data [1026]
Nov 17 20:00:22.36: [10109]: <-- data [1026]
Nov 17 20:00:22.36: [10109]: <-- data [1024]
Nov 17 20:00:22.36: [10109]: <-- data [1024]
Nov 17 20:00:24.36: [10109]: <-- data [1026]
Nov 17 20:00:24.36: [10109]: <-- data [1034]
Nov 17 20:00:24.36: [10109]: <-- data [1024]
Nov 17 20:00:26.36: [10109]: <-- data [1029]
Nov 17 20:00:26.36: [10109]: <-- data [1026]
Nov 17 20:00:26.36: [10109]: <-- data [1024]
Nov 17 20:00:26.36: [10109]: <-- data [1025]
Nov 17 20:00:28.35: [10109]: <-- data [1024]
Nov 17 20:00:28.35: [10109]: <-- data [127]
Nov 17 20:00:28.35: [10109]: SENT 24703 bytes of data
Nov 17 20:00:28.35: [10109]: SEND 1D RTC
Nov 17 20:00:28.35: [10109]: <-- data [9]
Nov 17 20:00:28.35: [10109]: SEND end page
Nov 17 20:00:28.35: [10109]: SEND send EOP (no more pages or documents)
Nov 17 20:00:28.35: [10109]: <-- data [2]
Nov 17 20:00:34.54: [10109]: --> [7:+FHS:00]
Nov 17 20:00:34.54: [10109]: REMOTE HANGUP: Normal and proper end of connection (code 0)
Nov 17 20:00:34.54: [10109]: SEND recv MCF (message confirmation)
Nov 17 20:00:34.54: [10109]: SEND FAX (00003958): FROM go@i3 TO 019RECVNO (page 1 of 1 sent in 0:25)
Nov 17 20:00:34.54: [10109]: SEND FAX (00003958): FROM go@i3 TO 019RECVNO (docq/doc2062.ps;01 sent
in 0:25)
Nov 17 20:00:34.54: [10109]: <-- [5:ATH0\r]
Nov 17 20:00:34.54: [10109]: --> [2:OK]
Nov 17 20:00:34.54: [10109]: MODEM set DTR OFF
Nov 17 20:00:34.55: [10109]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Nov 17 20:00:34.55: [10109]: SESSION END
== Rockwell receiving from USR class2.0/rtscts
Nov 17 20:00:00.57: [ 9967]: SESSION BEGIN 00003959 39019RECVNO
Nov 17 20:00:00.57: [ 9967]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Nov 17 20:00:00.57: [ 9967]: <-- [4:ATA\r]
Nov 17 20:00:06.65: [ 9967]: --> [7:CONNECT]
Nov 17 20:00:06.65: [ 9967]: ANSWER: FAX CONNECTION
Nov 17 20:00:06.65: [ 9967]: STATE CHANGE: ANSWERING -> RECEIVING
Nov 17 20:00:06.65: [ 9967]: MODEM input buffering enabled
Nov 17 20:00:06.65: [ 9967]: RECV FAX: begin
Nov 17 20:00:06.65: [ 9967]: MODEM input buffering disabled
Nov 17 20:00:06.65: [ 9967]: <-- HDLC<23:FF C0 02 0C EC 6C EC 4C 6C 04 9C 8C 0C 04 9C CC D4 04 04 04
04 04 04>
Nov 17 20:00:06.65: [ 9967]: <-- data [23]
Nov 17 20:00:06.65: [ 9967]: <-- data [2]
Nov 17 20:00:08.34: [ 9967]: --> [7:CONNECT]
Nov 17 20:00:08.34: [ 9967]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Nov 17 20:00:08.34: [ 9967]: <-- data [10]
Nov 17 20:00:08.34: [ 9967]: <-- data [2]
Nov 17 20:00:08.89: [ 9967]: --> [2:OK]
Nov 17 20:00:08.89: [ 9967]: <-- [9:AT+FRH=3\r]
Nov 17 20:00:09.54: [ 9967]: --> [7:CONNECT]
Nov 17 20:00:10.93: [ 9967]: --> HDLC<25:FF C0 C2 04 04 04 04 9C 1C EC 6C AC 2C CC 4C 8C 04 6C 0C 04
9C CC D4 E7 F5>
Nov 17 20:00:10.94: [ 9967]: --> [2:OK]
Nov 17 20:00:10.94: [ 9967]: REMOTE TSI "+39 06 123456789"
Nov 17 20:00:10.94: [ 9967]: <-- [9:AT+FRH=3\r]
Nov 17 20:00:10.96: [ 9967]: --> [7:CONNECT]
Nov 17 20:00:11.30: [ 9967]: --> HDLC<9:FF C8 C1 00 46 1F 00 3D 9B>
Nov 17 20:00:11.31: [ 9967]: --> [2:OK]
Nov 17 20:00:11.31: [ 9967]: REMOTE wants 14400 bit/s
Nov 17 20:00:11.31: [ 9967]: REMOTE wants page width 1728 pixels in 215 mm
Nov 17 20:00:11.31: [ 9967]: REMOTE wants unlimited page length
Nov 17 20:00:11.31: [ 9967]: REMOTE wants 7.7 line/mm
Nov 17 20:00:11.31: [ 9967]: REMOTE wants 1-D MR
Nov 17 20:00:11.31: [ 9967]: RECV training at v.17 14400 bit/s
Nov 17 20:00:11.31: [ 9967]: MODEM set XON/XOFF/DRAIN: input ignored, output generated
Nov 17 20:00:11.31: [ 9967]: <-- [11:AT+FRM=145\r]
Nov 17 20:00:12.91: [ 9967]: --> [7:CONNECT]
Nov 17 20:00:14.43: [ 9967]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Nov 17 20:00:14.43: [ 9967]: RECV: TCF 2679 bytes, 0% non-zero, 2657 zero-run
Nov 17 20:00:14.43: [ 9967]: --> [10:NO CARRIER]
Nov 17 20:00:14.43: [ 9967]: DELAY 75 ms
Nov 17 20:00:14.51: [ 9967]: <-- [9:AT+FTH=3\r]
Nov 17 20:00:14.56: [ 9967]: --> [7:CONNECT]
Nov 17 20:00:14.56: [ 9967]: <-- HDLC<3:FF C8 21>
Nov 17 20:00:14.56: [ 9967]: <-- data [3]
Nov 17 20:00:14.56: [ 9967]: <-- data [2]
Nov 17 20:00:15.88: [ 9967]: --> [2:OK]
Nov 17 20:00:15.88: [ 9967]: TRAINING succeeded
Nov 17 20:00:15.88: [ 9967]: MODEM input buffering enabled
Nov 17 20:00:15.88: [ 9967]: MODEM set XON/XOFF/FLUSH: input ignored, output generated
Nov 17 20:00:15.88: [ 9967]: <-- [11:AT+FRM=146\r]
Nov 17 20:00:16.36: [ 9967]: --> [7:CONNECT]
Nov 17 20:00:16.36: [ 9967]: RECV: begin page
Nov 17 20:00:30.18: [ 9967]: RECV/CQ: Bad 1D pixel count, row 2292, got 0, expected 1728
Nov 17 20:00:30.18: [ 9967]: RECV/CQ: Bad 1D pixel count, row 2293, got 0, expected 1728
Nov 17 20:00:30.18: [ 9967]: RECV/CQ: Bad 1D pixel count, row 2294, got 0, expected 1728
Nov 17 20:00:30.18: [ 9967]: RECV/CQ: Bad 1D pixel count, row 2295, got 0, expected 1728
Nov 17 20:00:30.18: [ 9967]: RECV/CQ: Bad 1D pixel count, row 2296, got 0, expected 1728
Nov 17 20:00:30.34: [ 9967]: RECV/CQ: Bad 1D pixel count, row 2297, got 2336, expected 1728
Nov 17 20:00:30.34: [ 9967]: RECV/CQ: Adjusting for trailing noise (6 run)
Nov 17 20:00:30.34: [ 9967]: RECV: 2292 total lines, 0 bad lines, 0 consecutive bad lines
Nov 17 20:00:30.34: [ 9967]: RECV: end page
Nov 17 20:00:30.34: [ 9967]: --> [10:NO CARRIER]
Nov 17 20:00:30.34: [ 9967]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Nov 17 20:00:30.34: [ 9967]: MODEM input buffering disabled
Nov 17 20:00:30.34: [ 9967]: <-- [9:AT+FRH=3\r]
Nov 17 20:00:30.70: [ 9967]: --> [7:CONNECT]
Nov 17 20:00:31.45: [ 9967]: --> HDLC<5:FF C8 F4 CC 66>
Nov 17 20:00:31.46: [ 9967]: --> [2:OK]
Nov 17 20:00:31.46: [ 9967]: RECV recv EOP (no more pages or documents)
Nov 17 20:00:31.46: [ 9967]: <-- [9:AT+FTH=3\r]
Nov 17 20:00:31.51: [ 9967]: --> [7:CONNECT]
Nov 17 20:00:31.51: [ 9967]: <-- HDLC<3:FF C8 31>
Nov 17 20:00:31.51: [ 9967]: <-- data [3]
Nov 17 20:00:31.51: [ 9967]: <-- data [2]
Nov 17 20:00:32.83: [ 9967]: --> [2:OK]
Nov 17 20:00:32.83: [ 9967]: RECV send MCF (message confirmation)
Nov 17 20:00:32.83: [ 9967]: RECV FAX (00003959): from +39 06 123456789, page 1 in 0:17, INF, 7.7
line/mm, 1-D MR, 14400 bit/s
Nov 17 20:00:32.83: [ 9967]: RECV FAX (00003959): recvq/fax00163.tif from +39 06 123456789, route to
<unspecified>, 1 pages in 0:26
Nov 17 20:00:32.83: [ 9967]: <-- [9:AT+FRH=3\r]
Nov 17 20:00:33.37: [ 9967]: --> [7:CONNECT]
Nov 17 20:00:34.23: [ 9967]: --> HDLC<5:FF C8 5F C8 E7>
Nov 17 20:00:34.24: [ 9967]: --> [2:OK]
Nov 17 20:00:34.24: [ 9967]: MODEM input buffering enabled
Nov 17 20:00:34.24: [ 9967]: RECV FAX: bin/faxrcvd "recvq/fax00163.tif" "ttyS2" "00003959" ""
Nov 17 20:00:34.47: [ 9967]: RECV FAX: end
Nov 17 20:00:34.47: [ 9967]: SESSION END
== USR class1/xonxoff sending
Nov 17 20:05:01.48: [10389]: SESSION BEGIN 00003962 39019RECVNO
Nov 17 20:05:01.48: [10389]: SEND FAX: JOB 2048 DEST 019RECVNO COMMID 00003962
Nov 17 20:05:01.48: [10389]: MODEM set DTR OFF
Nov 17 20:05:01.48: [10389]: DELAY 2600 ms
Nov 17 20:05:04.07: [10389]: MODEM set DTR ON
Nov 17 20:05:04.07: [10389]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow
XON/XOFF
Nov 17 20:05:04.07: [10389]: MODEM flush i/o
Nov 17 20:05:04.07: [10389]: <-- [4:ATZ\r]
Nov 17 20:05:04.38: [10389]: --> [3:ATZ]
Nov 17 20:05:04.38: [10389]: --> [2:OK]
Nov 17 20:05:04.38: [10389]: <-- [17:ATE0V1Q0X3S0=0H0\r]
Nov 17 20:05:04.56: [10389]: --> [16:ATE0V1Q0X3S0=0H0]
Nov 17 20:05:04.56: [10389]: --> [2:OK]
Nov 17 20:05:04.56: [10389]: <-- [32:ATS8=2S7=60&H2&I2&R1S13=1&D2&C1\r]
Nov 17 20:05:04.75: [10389]: --> [2:OK]
Nov 17 20:05:04.75: [10389]: <-- [12:AT+FCLASS=1\r]
Nov 17 20:05:04.80: [10389]: --> [2:OK]
Nov 17 20:05:04.80: [10389]: <-- [12:AT+FCLASS=0\r]
Nov 17 20:05:04.87: [10389]: --> [2:OK]
Nov 17 20:05:04.87: [10389]: <-- [5:ATM0\r]
Nov 17 20:05:05.04: [10389]: --> [2:OK]
Nov 17 20:05:05.04: [10389]: STATE CHANGE: RUNNING -> SENDING
Nov 17 20:05:05.04: [10389]: MODEM input buffering enabled
Nov 17 20:05:05.04: [10389]: <-- [12:AT+FCLASS=1\r]
Nov 17 20:05:05.19: [10389]: --> [2:OK]
Nov 17 20:05:05.19: [10389]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Nov 17 20:05:05.19: [10389]: DIAL 019RECVNO
Nov 17 20:05:05.19: [10389]: <-- [15:ATDT019RECVNO@\r]
Nov 17 20:06:10.12: [10389]: --> [9:NO ANSWER]
Nov 17 20:06:10.12: [10389]: SEND FAILED: No answer from remote
Nov 17 20:06:10.12: [10389]: <-- [5:ATH0\r]
Nov 17 20:06:10.39: [10389]: --> [2:OK]
Nov 17 20:06:10.39: [10389]: MODEM set DTR OFF
Nov 17 20:06:10.39: [10389]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Nov 17 20:06:10.39: [10389]: SESSION END
== Rockwell receiving from USR class1/xonxoff
Nov 17 20:05:12.49: [ 9967]: SESSION BEGIN 00003963 39019RECVNO
Nov 17 20:05:12.49: [ 9967]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Nov 17 20:05:12.49: [ 9967]: <-- [4:ATA\r]
Nov 17 20:05:18.55: [ 9967]: --> [7:CONNECT]
Nov 17 20:05:18.55: [ 9967]: ANSWER: FAX CONNECTION
Nov 17 20:05:18.55: [ 9967]: STATE CHANGE: ANSWERING -> RECEIVING
Nov 17 20:05:18.55: [ 9967]: MODEM input buffering enabled
Nov 17 20:05:18.55: [ 9967]: RECV FAX: begin
Nov 17 20:05:18.55: [ 9967]: MODEM input buffering disabled
Nov 17 20:05:18.55: [ 9967]: <-- HDLC<23:FF C0 02 0C EC 6C EC 4C 6C 04 9C 8C 0C 04 9C CC D4 04 04 04
04 04 04>
Nov 17 20:05:18.55: [ 9967]: <-- data [23]
Nov 17 20:05:18.55: [ 9967]: <-- data [2]
Nov 17 20:05:20.23: [ 9967]: --> [7:CONNECT]
Nov 17 20:05:20.23: [ 9967]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Nov 17 20:05:20.23: [ 9967]: <-- data [10]
Nov 17 20:05:20.23: [ 9967]: <-- data [2]
Nov 17 20:05:20.78: [ 9967]: --> [2:OK]
Nov 17 20:05:20.78: [ 9967]: <-- [9:AT+FRH=3\r]
Nov 17 20:05:23.88: [ 9967]: --> [0:]
Nov 17 20:05:23.88: [ 9967]: MODEM <Empty line>
Nov 17 20:05:23.88: [ 9967]: MODEM TIMEOUT: waiting for v.21 carrier
Nov 17 20:05:23.88: [ 9967]: <-- data [1]
Nov 17 20:05:23.93: [ 9967]: --> [2:OK]
Nov 17 20:05:23.93: [ 9967]: DELAY 1500 ms
Nov 17 20:05:25.43: [ 9967]: <-- [9:AT+FTH=3\r]
Nov 17 20:05:25.48: [ 9967]: --> [7:CONNECT]
Nov 17 20:05:25.48: [ 9967]: <-- HDLC<23:FF C0 02 0C EC 6C EC 4C 6C 04 9C 8C 0C 04 9C CC D4 04 04 04
04 04 04>
Nov 17 20:05:25.48: [ 9967]: <-- data [23]
Nov 17 20:05:25.48: [ 9967]: <-- data [2]
Nov 17 20:05:27.27: [ 9967]: --> [7:CONNECT]
Nov 17 20:05:27.27: [ 9967]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Nov 17 20:05:27.27: [ 9967]: <-- data [10]
Nov 17 20:05:27.27: [ 9967]: <-- data [2]
Nov 17 20:05:27.81: [ 9967]: --> [2:OK]
Nov 17 20:05:27.81: [ 9967]: <-- [9:AT+FRH=3\r]
Nov 17 20:05:30.91: [ 9967]: --> [0:]
Nov 17 20:05:30.91: [ 9967]: MODEM <Empty line>
Nov 17 20:05:30.91: [ 9967]: MODEM TIMEOUT: waiting for v.21 carrier
Nov 17 20:05:30.91: [ 9967]: <-- data [1]
Nov 17 20:05:30.96: [ 9967]: --> [2:OK]
Nov 17 20:05:30.96: [ 9967]: DELAY 1500 ms
Nov 17 20:05:32.46: [ 9967]: <-- [9:AT+FTH=3\r]
Nov 17 20:05:32.51: [ 9967]: --> [7:CONNECT]
Nov 17 20:05:32.51: [ 9967]: <-- HDLC<23:FF C0 02 0C EC 6C EC 4C 6C 04 9C 8C 0C 04 9C CC D4 04 04 04
04 04 04>
Nov 17 20:05:32.51: [ 9967]: <-- data [23]
Nov 17 20:05:32.51: [ 9967]: <-- data [2]
Nov 17 20:05:34.30: [ 9967]: --> [7:CONNECT]
Nov 17 20:05:34.30: [ 9967]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Nov 17 20:05:34.30: [ 9967]: <-- data [10]
Nov 17 20:05:34.30: [ 9967]: <-- data [2]
Nov 17 20:05:34.84: [ 9967]: --> [2:OK]
Nov 17 20:05:34.84: [ 9967]: <-- [9:AT+FRH=3\r]
Nov 17 20:05:37.94: [ 9967]: --> [0:]
Nov 17 20:05:37.94: [ 9967]: MODEM <Empty line>
Nov 17 20:05:37.94: [ 9967]: MODEM TIMEOUT: waiting for v.21 carrier
Nov 17 20:05:37.94: [ 9967]: <-- data [1]
Nov 17 20:05:37.99: [ 9967]: --> [2:OK]
Nov 17 20:05:37.99: [ 9967]: DELAY 1500 ms
Nov 17 20:05:39.49: [ 9967]: <-- [9:AT+FTH=3\r]
Nov 17 20:05:39.54: [ 9967]: --> [7:CONNECT]
Nov 17 20:05:39.54: [ 9967]: <-- HDLC<23:FF C0 02 0C EC 6C EC 4C 6C 04 9C 8C 0C 04 9C CC D4 04 04 04
04 04 04>
Nov 17 20:05:39.54: [ 9967]: <-- data [23]
Nov 17 20:05:39.54: [ 9967]: <-- data [2]
Nov 17 20:05:41.33: [ 9967]: --> [7:CONNECT]
Nov 17 20:05:41.33: [ 9967]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Nov 17 20:05:41.33: [ 9967]: <-- data [10]
Nov 17 20:05:41.33: [ 9967]: <-- data [2]
Nov 17 20:05:41.87: [ 9967]: --> [2:OK]
Nov 17 20:05:41.87: [ 9967]: <-- [9:AT+FRH=3\r]
Nov 17 20:05:44.97: [ 9967]: --> [0:]
Nov 17 20:05:44.97: [ 9967]: MODEM <Empty line>
Nov 17 20:05:44.97: [ 9967]: MODEM TIMEOUT: waiting for v.21 carrier
Nov 17 20:05:44.97: [ 9967]: <-- data [1]
Nov 17 20:05:45.02: [ 9967]: --> [2:OK]
Nov 17 20:05:45.02: [ 9967]: DELAY 1500 ms
Nov 17 20:05:46.52: [ 9967]: <-- [9:AT+FTH=3\r]
Nov 17 20:05:46.58: [ 9967]: --> [7:CONNECT]
Nov 17 20:05:46.58: [ 9967]: <-- HDLC<23:FF C0 02 0C EC 6C EC 4C 6C 04 9C 8C 0C 04 9C CC D4 04 04 04
04 04 04>
Nov 17 20:05:46.58: [ 9967]: <-- data [23]
Nov 17 20:05:46.58: [ 9967]: <-- data [2]
Nov 17 20:05:48.36: [ 9967]: --> [7:CONNECT]
Nov 17 20:05:48.36: [ 9967]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Nov 17 20:05:48.36: [ 9967]: <-- data [10]
Nov 17 20:05:48.36: [ 9967]: <-- data [2]
Nov 17 20:05:48.90: [ 9967]: --> [2:OK]
Nov 17 20:05:48.90: [ 9967]: <-- [9:AT+FRH=3\r]
Nov 17 20:05:52.00: [ 9967]: --> [0:]
Nov 17 20:05:52.00: [ 9967]: MODEM <Empty line>
Nov 17 20:05:52.00: [ 9967]: MODEM TIMEOUT: waiting for v.21 carrier
Nov 17 20:05:52.00: [ 9967]: <-- data [1]
Nov 17 20:05:52.05: [ 9967]: --> [2:OK]
Nov 17 20:05:52.05: [ 9967]: DELAY 1500 ms
Nov 17 20:05:53.55: [ 9967]: <-- [9:AT+FTH=3\r]
Nov 17 20:05:53.60: [ 9967]: --> [7:CONNECT]
Nov 17 20:05:53.60: [ 9967]: <-- HDLC<23:FF C0 02 0C EC 6C EC 4C 6C 04 9C 8C 0C 04 9C CC D4 04 04 04
04 04 04>
Nov 17 20:05:53.60: [ 9967]: <-- data [23]
Nov 17 20:05:53.60: [ 9967]: <-- data [2]
Nov 17 20:05:55.39: [ 9967]: --> [7:CONNECT]
Nov 17 20:05:55.39: [ 9967]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Nov 17 20:05:55.39: [ 9967]: <-- data [10]
Nov 17 20:05:55.39: [ 9967]: <-- data [2]
Nov 17 20:05:55.93: [ 9967]: --> [2:OK]
Nov 17 20:05:55.93: [ 9967]: <-- [9:AT+FRH=3\r]
Nov 17 20:05:59.03: [ 9967]: --> [0:]
Nov 17 20:05:59.03: [ 9967]: MODEM <Empty line>
Nov 17 20:05:59.03: [ 9967]: MODEM TIMEOUT: waiting for v.21 carrier
Nov 17 20:05:59.03: [ 9967]: <-- data [1]
Nov 17 20:05:59.08: [ 9967]: --> [2:OK]
Nov 17 20:05:59.08: [ 9967]: RECV FAX: No answer (T.30 T1 timeout)
Nov 17 20:05:59.08: [ 9967]: RECV FAX: end
Nov 17 20:05:59.08: [ 9967]: SESSION END
============================
Firmware update is not an option due to the huge installed base.
USR
Product type Italy External MSK
Options HST,V32bis,Terbo,V.FC,V.34
Fax Options Class 1/Class 2.0
Clock Freq 20.16Mhz
Eprom 256k
Ram 32k
Supervisor date 11/15/95
DSP date 07/05/95
Supervisor rev 039-6.2.2
DSP rev 1.2.2
-----------------
V2010-K56_DLS
RCV56DPF L8570A Rev 45.0/45.0
--
giulioo@pobox.com
____________________ HylaFAX(tm) Users Mailing List _______________________
To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
