|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] ISIHP 4S modem config
Hello,
im am locking for a modem-config
file for the MultiTech ISIHP 4S. can
someone tell what kind of modems they use
on such cards? a european config file
would just be fine. i used the faxaddmodem
script but it does not work in all cases.
thanks a lot
Axel
CountryCode: 49
AreaCode: 40
FAXNumber: +xxxxxxxxxxxxxx
LongDistancePrefix: 00
InternationalPrefix: 000
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "XXXXXXXXXXXXXXXX"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%p of %%t"
MaxRecvPages: 25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2 # use this to supply a hint
ModemRate: 19200 # max rate for DCE-DTE
communication
#ModemFlowControl: xonxoff # XON/XOFF flow control assumed
#ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier
(or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd: ATDT%s@ # T for tone dialing, @ for
silence
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds: "" # stuff to do when modem
is reset
#ModemAnswerCmd: ATA # use this to answer
phone
#ModemNoFlowCmd: AT&K # disable flow control
cmd
#ModemHardFlowCmd: AT&K3 # hardware flow control cmd
#ModemSoftFlowCmd: AT&K4 # software flow control cmd
#ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd: ATE0 # disable command echo
#ModemVerboseResultsCmd: ATV1 # enable verbose command
results
#ModemResultCodesCmd: ATQ0 # enable result codes
#ModemOnHookCmd: ATH0 # place phone on hook
(hangup)
#ModemSoftResetCmd: ATZ # do soft reset of modem
#ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2
seconds
#ModemRecvFillOrder: LSB2MSB # bit order of received
facsimile
#ModemSendFillOrder: LSB2MSB # bit order modem expects for
transmit
ModemSendFillOrder: LSB2MSB # as expected
ModemRecvFillOrder: MSB2LSB # opposite of what makes
sense
# Configuration parameters for Class 2
modems.
#
Class2Cmd: AT+FCLASS=2 # command to enter class 2
Class2BORCmd: AT+FBOR=0 # bit order for phase B/C/D
(direct)
Class2RELCmd: AT+FREL=1 # byte-align EOL codes on recv
Class2CQCmd: "" # commands to enable copy
quality proc.
Class2AbortCmd: AT+FK # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality
capabilities
Class2DCCQueryCmd: AT+FDCC=? # query for modem capabilities
Class2TBCCmd: AT+FTBC=0 # setup stream mode
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FPHCTO=30 # set phase C timeout parameter
Class2BUGCmd: AT+FBUG=1 # enable HDLC frame tracing
Class2LIDCmd: AT+FLID # set local identifier command
Class2DCCCmd: AT+FDCC # set modem capabilities command
Class2DISCmd: AT+FDIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command
hack
Class2CIGCmd: AT+FCIG # set polling identifier command
Class2PTSCmd: AT+FPTS # set post-page status command
Class2SPLCmd: AT+FSPL # set polling indicator command
#
# If Class2RecvDataTrigger is not set, then it is set to DC1
#
Class2RecvDataTrigger: "" # character sent to modem to
start recv
Class2XmitWaitForXON: yes # if true, wait for XON before
send
**********************************************************************
Nov 03 15:49:14.60: [ 593]: SESSION BEGIN 00000044 494030069391
Nov 03 15:49:14.60: [ 593]: <-- [4:ATA\r]
Nov 03 15:49:28.39: [ 593]: --> [5:+FCON]
Nov 03 15:49:28.39: [ 593]: ANSWER: FAX CONNECTION
Nov 03 15:49:28.39: [ 593]: RECV FAX: begin
Nov 03 15:49:28.39: [ 593]: --> [28:+FTSI:" +xxx"]
Nov 03 15:49:28.39: [ 593]: REMOTE TSI "+xxx"
Nov 03 15:49:28.39: [ 593]: --> [21:+FDCS:0,5,0,2,0,0,0,1]
Nov 03 15:49:28.39: [ 593]: REMOTE wants 14400 bit/s
Nov 03 15:49:28.39: [ 593]: REMOTE wants page width 1728 pixels in 215
mm
Nov 03 15:49:28.39: [ 593]: REMOTE wants unlimited page length
Nov 03 15:49:28.39: [ 593]: REMOTE wants 3.85 line/mm
Nov 03 15:49:28.39: [ 593]: REMOTE wants 1-D MR
Nov 03 15:49:28.39: [ 593]: --> [2:OK]
Nov 03 15:49:28.39: [ 593]: <-- [7:AT+FDR\r]
Nov 03 15:49:28.39: [ 593]: --> [8:+FHNG:72]
Nov 03 15:49:28.39: [ 593]: REMOTE HANGUP: COMREC error (code 72)
Nov 03 15:49:28.39: [ 593]: RECV FAX (00000044): recvq/fax00036.tif
from +49 40 30069 199, route to <unspecified>, 0 pages in 0:00
Nov 03 15:49:28.39: [ 593]: RECV FAX: COMREC error
Nov 03 15:49:28.39: [ 593]: RECV FAX (00000044): session with +49 40
30069 199 terminated abnormally: COMREC error
Nov 03 15:49:28.39: [ 593]: RECV FAX: bin/faxrcvd "recvq/fax00036.tif"
"ttyM1i" "00000044" "COMREC error"
--
http://www.infoseek.de
Axel Christiansen - Technik/Tech Department - Netzwerk Administration
e-Mail: a.christiansen@webseek.de
WSI Webseek Infoservice GmbH & Co. KG
Tel./Phone +49-40-300 69 321 Fax +49-40-300 69 199
Buero/Office: Herrengraben 3, D- 20459 Hamburg
Post/mail: Brieffach 8250, D- 20350 Hamburg
____________________ HylaFAX(tm) Users Mailing List _______________________
To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
