|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] [hylafax-users]
"Carlo Georges" <georgesc@pt.lu> writes:
> Hello all
> I'm new to hylafax formerly used the mgettty + sendfax pachkage with no
> problems.
> When i try to send to my canon multipass 10 fax I get a transmission error
> with following message
> Oct 15 15:36:51.01: [26621]: SESSION BEGIN 00000004 352415552084
> Oct 15 15:36:51.01: [26621]: SEND FAX: JOB 1 DEST 552084 COMMID 00000004
> Oct 15 15:36:51.01: [26621]: DELAY 2600 ms
> Oct 15 15:36:53.62: [26621]: <-- [15:ATE0V1Q0S0=0H0\r]
> Oct 15 15:36:53.64: [26621]: --> [2:OK]
> Oct 15 15:36:53.64: [26621]: <-- [12:ATS8=2S7=60\r]
> Oct 15 15:36:53.66: [26621]: --> [2:OK]
> Oct 15 15:36:53.66: [26621]: <-- [14:AT+FCLASS=2.0\r]
> Oct 15 15:36:53.68: [26621]: --> [2:OK]
> Oct 15 15:36:53.68: [26621]: <-- [9:AT+FLO=0\r]
^^^^^^^^
No flow control; too bad. What modem are you using?
> Oct 15 15:36:53.70: [26621]: --> [2:OK]
> Oct 15 15:36:53.70: [26621]: <-- [9:AT+FPP=0\r]
> Oct 15 15:36:53.72: [26621]: --> [2:OK]
> Oct 15 15:36:53.72: [26621]: <-- [9:AT+FBO=0\r]
> Oct 15 15:36:53.74: [26621]: --> [2:OK]
> Oct 15 15:36:53.74: [26621]: <-- [10:AT+FCT=30\r]
> Oct 15 15:36:53.76: [26621]: --> [2:OK]
> Oct 15 15:36:53.76: [26621]: <-- [15:AT+FNR=1,1,1,1\r]
> Oct 15 15:36:53.78: [26621]: --> [2:OK]
> Oct 15 15:37:57.75: [26621]: SEND 1D RTC
> Oct 15 15:37:57.75: [26621]: <-- data [9]
> Oct 15 15:37:57.76: [26621]: SEND end page
> Oct 15 15:37:57.76: [26621]: SEND send EOP (no more pages or documents)
> Oct 15 15:37:57.76: [26621]: <-- data [2]
> Oct 15 15:38:45.81: [26621]: --> [7:+FHS:43]
> Oct 15 15:38:45.81: [26621]: REMOTE HANGUP: DTE to DCE data underflow (code
> 43)
> Oct 15 15:38:45.81: [26621]: SEND: DTE to DCE data underflow; Giving up
> after 3$
> Oct 15 15:38:45.81: [26621]: <-- [5:ATH0\r]
> Oct 15 15:38:47.01: [26621]: --> [2:OK]
> Oct 15 15:38:47.01: [26621]: SESSION END
>
> What does the code 43 mean and is there a way to correct this
Your modem should be properly configured. Try to use an appropriate
predefined config template.
Hope to hear from you soon,
Dmitry
____________________ HylaFAX(tm) Users Mailing List _______________________
To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
