|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Occasional problem
Occasionally, when sending I hear the exchange going on over and over where
the two modems seem to try to connect but repeatedly never handshake to
completion.
The modem is a Telebit Worldblazer operating as a Class 1.
Software is hylafax-4.1beta2-4rh6.src.rpm.
I have heard this same exchange occasionally on both incoming and outgoing
faxes with other software in the past so this may be a firmware problem. I
think theremay be a workaround.
Would someone comment on ideas or additional steps necessary?
Your facsimile job to +12062821510 failed because:
Communication failure during Phase B/C; Giving up after 3 attempts to
send same page
---- Transcript of session follows ----
Sep 28 06:33:36.36: [ 9061]: SESSION BEGIN 00002292 12062821510
Sep 28 06:33:36.36: [ 9061]: SEND FAX: JOB 1177 DEST +12062821510 COMMID
00002292
Sep 28 06:33:36.36: [ 9061]: DELAY 3200 ms
Sep 28 06:33:39.56: [ 9061]: <-- [4:ATZ\r]
Sep 28 06:33:40.94: [ 9061]: --> [3:ATZ]
Sep 28 06:33:40.94: [ 9061]: --> [2:OK]
Sep 28 06:33:40.94: [ 9061]: <-- [15:ATE0V1Q0S0=0H0\r]
Sep 28 06:33:40.97: [ 9061]: --> [14:ATE0V1Q0S0=0H0]
Sep 28 06:33:40.97: [ 9061]: --> [2:OK]
Sep 28 06:33:40.97: [ 9061]: <-- [23:ATS8=2S7=60S58=2&D3&C1\r]
Sep 28 06:33:41.01: [ 9061]: --> [2:OK]
Sep 28 06:33:41.01: [ 9061]: <-- [12:AT+FCLASS=2\r]
Sep 28 06:33:41.04: [ 9061]: --> [2:OK]
Sep 28 06:33:41.04: [ 9061]: <-- [10:AT+FTBC=0\r]
Sep 28 06:33:41.06: [ 9061]: --> [2:OK]
Sep 28 06:33:41.06: [ 9061]: <-- [10:AT+FBOR=0\r]
Sep 28 06:33:41.09: [ 9061]: --> [2:OK]
Sep 28 06:33:41.09: [ 9061]: <-- [13:AT+FPHCTO=30\r]
Sep 28 06:33:41.12: [ 9061]: --> [2:OK]
Sep 28 06:33:41.12: [ 9061]: <-- [24:AT+FDCC=1,3,2,2,0,0,0,0\r]
Sep 28 06:33:41.16: [ 9061]: --> [2:OK]
Sep 28 06:33:41.16: [ 9061]: <-- [7:ATL0M1\r]
Sep 28 06:33:41.18: [ 9061]: --> [2:OK]
Sep 28 06:33:41.18: [ 9061]: <-- [12:AT+FCLASS=2\r]
Sep 28 06:33:41.31: [ 9061]: --> [2:OK]
Sep 28 06:33:41.31: [ 9061]: <-- [10:AT+FTBC=0\r]
Sep 28 06:33:41.44: [ 9061]: --> [2:OK]
Sep 28 06:33:41.44: [ 9061]: <-- [10:AT+FBOR=0\r]
Sep 28 06:33:41.57: [ 9061]: --> [2:OK]
Sep 28 06:33:41.57: [ 9061]: <-- [13:AT+FPHCTO=30\r]
Sep 28 06:33:41.70: [ 9061]: --> [2:OK]
Sep 28 06:33:41.70: [ 9061]: <-- [24:AT+FDCC=1,3,2,2,0,0,0,0\r]
Sep 28 06:33:41.84: [ 9061]: --> [2:OK]
Sep 28 06:33:41.84: [ 9061]: <-- [28:AT+FLID="Blackdog Software"\r]
Sep 28 06:33:41.97: [ 9061]: --> [2:OK]
Sep 28 06:33:41.97: [ 9061]: <-- [24:AT+FDIS=1,3,0,2,0,0,0,0\r]
Sep 28 06:33:42.11: [ 9061]: --> [2:OK]
Sep 28 06:33:42.13: [ 9061]: DIAL 2062821510
Sep 28 06:33:42.13: [ 9061]: <-- [15:ATDT2062821510\r]
Sep 28 06:33:45.80: [ 9061]: --> [7:DIALING]
Sep 28 06:33:53.98: [ 9061]: --> [5:RRING]
Sep 28 06:34:00.53: [ 9061]: --> [5:+FCON]
Sep 28 06:34:03.01: [ 9061]: --> [39:+FNSF:00 00 6A AA AA 00 11 0D 01 FA 00 ]
Sep 28 06:34:03.01: [ 9061]: REMOTE NSF "00 00 6A AA AA 00 11 0D 01 FA 00"
Sep 28 06:34:03.01: [ 9061]: NSF remote fax equipment: unknown
Sep 28 06:34:03.01: [ 9061]: --> [28:+FCSI:" 2062821510"]
Sep 28 06:34:03.01: [ 9061]: REMOTE CSI "2062821510"
Sep 28 06:34:03.01: [ 9061]: --> [21:+FDIS:1,3,0,2,0,0,0,4]
Sep 28 06:34:03.01: [ 9061]: --> [2:OK]
Sep 28 06:34:03.01: [ 9061]: REMOTE best rate 9600 bit/s
Sep 28 06:34:03.01: [ 9061]: REMOTE max page width 1728 pixels in 215 mm
Sep 28 06:34:03.01: [ 9061]: REMOTE max unlimited page length
Sep 28 06:34:03.01: [ 9061]: REMOTE best vres 7.7 line/mm
Sep 28 06:34:03.01: [ 9061]: REMOTE best format 1-D MR
Sep 28 06:34:03.01: [ 9061]: REMOTE best 20 ms, 10 ms/scanline
Sep 28 06:34:03.01: [ 9061]: USE 9600 bit/s
Sep 28 06:34:03.01: [ 9061]: USE 20 ms, 10 ms/scanline
Sep 28 06:34:03.01: [ 9061]: SEND file "docq/doc2727.ps;31"
Sep 28 06:34:03.19: [ 9061]: USE page width 1728 pixels in 215 mm
Sep 28 06:34:03.19: [ 9061]: USE unlimited page length
Sep 28 06:34:03.19: [ 9061]: USE 7.7 line/mm
Sep 28 06:34:03.19: [ 9061]: USE 1-D MR
Sep 28 06:34:03.19: [ 9061]: <-- [7:AT+FDT\r]
Sep 28 06:34:58.44: [ 9061]: --> [10:NO CARRIER]
Sep 28 06:34:58.44: [ 9061]: MODEM No carrier
Sep 28 06:34:58.44: [ 9061]: <-- [6:AT+FK\r]
Sep 28 06:34:58.56: [ 9061]: --> [5:ERROR]
Sep 28 06:34:58.56: [ 9061]: MODEM Command error
Sep 28 06:34:58.56: [ 9061]: SEND: Communication failure during Phase B/C;
Giving up after 3 attempts to send same page "docq/doc2727.ps;31", dirnum 0
Sep 28 06:34:58.56: [ 9061]: <-- [5:ATH0\r]
Sep 28 06:34:58.69: [ 9061]: --> [2:OK]
Sep 28 06:34:58.69: [ 9061]: SESSION END
Paul Franz
PAF Consulting Engineers | 427 - 140th Ave NE
(425)641-8202 voice | Bellevue, WA 98005
(801)749-8480 fax | <http://blackdog.bellevue.wa.us/>
____________________ HylaFAX(tm) Users Mailing List _______________________
To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
