|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] Sending Faxes after 3 Attempts
Kai.Guenzel@Bertelsmann.de schrieb:
>
> > Hi there,
> >
> > we have a problem with our Hyla Fax Server.
> > The server sends a fax which is received successfully by the recipient.
> > But the recipient fax does not send an ok to Hyla Fax. This leads Hyla
> > Fax to the assumption that it has to send it again. The result is that
> > the recipient receives the same fax three times and Hyla Fax announces the
> > error below.
> >
> > Does somebody know how to configure Hyla Fax in a way that it does not repeat
> > the fax if the sending process itself was ok, but the final acknowledgement is missing?
> >
> > Thanks in advance,
> >
> > Kai
> >
Hi Kai,
i don't know a chance to configure hylafax that way.
but you should remember:
Hylafax asks at the end of transmission, as ruled out in the CCITT.
the destination does not work according to that protocol.
the only chance ist to change to source.
HIH
/Matthias
> > Your facsimile job to 60010 failed because:
> > No response to MPS repeated 3 times; Giving up after 3 attempts to send same page
> >
> > ---- Transcript of session follows ----
> >
> > Sep 05 14:35:02.73: [ 1955]: SESSION BEGIN ......
> > Sep 05 14:35:02.73: [ 1955]: SEND FAX: JOB 157 DEST ..... COMMID 00000348
> > Sep 05 14:35:02.73: [ 1955]: MODEM set DTR OFF
> > Sep 05 14:35:02.73: [ 1955]: DELAY 2600 ms
> > Sep 05 14:35:05.33: [ 1955]: MODEM set DTR ON
> > Sep 05 14:35:05.33: [ 1955]: MODEM set baud rate: 19200 baud, input flow RTS/CTS, output flow RTS/CTS
> > Sep 05 14:35:05.33: [ 1955]: MODEM flush i/o
> > Sep 05 14:35:05.33: [ 1955]: <-- [31:AT&H3&I2&R2S7=90E0V1Q0X4S0=0H0\r]
> > Sep 05 14:35:05.48: [ 1955]: --> [2:OK]
> > Sep 05 14:35:05.48: [ 1955]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=1&D2&C1\r]
> > Sep 05 14:35:05.63: [ 1955]: --> [2:OK]
> > Sep 05 14:35:05.63: [ 1955]: <-- [14:AT+FCLASS=2.0\r]
> > Sep 05 14:35:05.77: [ 1955]: --> [2:OK]
> > Sep 05 14:35:05.77: [ 1955]: <-- [9:AT+FLO=2\r]
> > Sep 05 14:35:05.91: [ 1955]: --> [2:OK]
> > Sep 05 14:35:05.91: [ 1955]: <-- [9:AT+FPP=0\r]
> > Sep 05 14:35:06.05: [ 1955]: --> [2:OK]
> > Sep 05 14:35:06.05: [ 1955]: <-- [9:AT+FBO=0\r]
> > Sep 05 14:35:06.19: [ 1955]: --> [2:OK]
> > Sep 05 14:35:06.19: [ 1955]: <-- [10:AT+FCT=30\r]
> > Sep 05 14:35:06.33: [ 1955]: --> [2:OK]
> > Sep 05 14:35:06.33: [ 1955]: <-- [15:AT+FNR=1,1,1,0\r]
> > Sep 05 14:35:06.47: [ 1955]: --> [2:OK]
> > Sep 05 14:35:06.47: [ 1955]: <-- [9:AT+FIE=0\r]
> > Sep 05 14:35:06.61: [ 1955]: --> [2:OK]
> > Sep 05 14:35:06.61: [ 1955]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
> > Sep 05 14:35:06.76: [ 1955]: --> [2:OK]
> > Sep 05 14:35:06.76: [ 1955]: <-- [5:ATM0\r]
> > Sep 05 14:35:06.90: [ 1955]: --> [2:OK]
> > Sep 05 14:35:06.90: [ 1955]: MODEM input buffering enabled
> > Sep 05 14:35:06.90: [ 1955]: <-- [14:AT+FCLASS=2.0\r]
> > Sep 05 14:35:07.14: [ 1955]: --> [2:OK]
> > Sep 05 14:35:07.14: [ 1955]: <-- [9:AT+FLO=2\r]
> > Sep 05 14:35:07.38: [ 1955]: --> [2:OK]
> > Sep 05 14:35:07.38: [ 1955]: <-- [9:AT+FPP=0\r]
> > Sep 05 14:35:07.62: [ 1955]: --> [2:OK]
> > Sep 05 14:35:07.62: [ 1955]: <-- [9:AT+FBO=0\r]
> > Sep 05 14:35:07.85: [ 1955]: --> [2:OK]
> > Sep 05 14:35:07.86: [ 1955]: <-- [10:AT+FCT=30\r]
> > Sep 05 14:35:08.09: [ 1955]: --> [2:OK]
> > Sep 05 14:35:08.09: [ 1955]: <-- [15:AT+FNR=1,1,1,0\r]
> > Sep 05 14:35:08.33: [ 1955]: --> [2:OK]
> > Sep 05 14:35:08.33: [ 1955]: <-- [9:AT+FIE=0\r]
> > Sep 05 14:35:08.57: [ 1955]: --> [2:OK]
> > Sep 05 14:35:08.57: [ 1955]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
> > Sep 05 14:35:08.82: [ 1955]: --> [2:OK]
> > Sep 05 14:35:08.82: [ 1955]: <-- [15:AT+FLI="innxs"\r]
> > Sep 05 14:35:09.06: [ 1955]: --> [2:OK]
> > Sep 05 14:35:09.07: [ 1955]: DIAL 022194860010
> > Sep 05 14:35:09.07: [ 1955]: <-- [21:ATX3DT0w022194860010\r]
> > Sep 05 14:35:23.82: [ 1955]: --> [4:+FCO]
> > Sep 05 14:35:27.54: [ 1955]: --> [27:+FCI:" +49 221 0010"]
> > Sep 05 14:35:27.54: [ 1955]: REMOTE CSI "+49 221 0010"
> > Sep 05 14:35:27.54: [ 1955]: --> [20:+FIS:1,5,0,2,1,0,0,1]
> > Sep 05 14:35:27.54: [ 1955]: --> [2:OK]
> > Sep 05 14:35:27.54: [ 1955]: REMOTE best rate 14400 bit/s
> > Sep 05 14:35:27.54: [ 1955]: REMOTE max page width 1728 pixels in 215 mm
> > Sep 05 14:35:27.54: [ 1955]: REMOTE max unlimited page length
> > Sep 05 14:35:27.54: [ 1955]: REMOTE best vres 7.7 line/mm
> > Sep 05 14:35:27.54: [ 1955]: REMOTE best format 2-D MR
> > Sep 05 14:35:27.54: [ 1955]: REMOTE best 5 ms/scanline>
> > Sep 05 14:35:27.54: [ 1955]: USE 14400 bit/s
> > Sep 05 14:35:27.54: [ 1955]: USE 5 ms/scanline
> > Sep 05 14:35:27.54: [ 1955]: SEND file "docq/doc157.ps;00"
> > Sep 05 14:35:27.54: [ 1955]: USE page width 1728 pixels in 215 mm
> > Sep 05 14:35:27.54: [ 1955]: USE unlimited page length
> > Sep 05 14:35:27.54: [ 1955]: USE 3.85 line/mm
> > Sep 05 14:35:27.54: [ 1955]: USE 1-D MR
> > Sep 05 14:35:27.54: [ 1955]: <-- [23:AT+FIS=0,5,0,2,0,0,0,1\r]
> > Sep 05 14:35:27.79: [ 1955]: --> [2:OK]
> > Sep 05 14:35:27.79: [ 1955]: <-- [7:AT+FDT\r]
> > Sep 05 14:35:28.06: [ 1955]: --> [20:+FCS:0,5,0,2,0,0,0,1]
> > Sep 05 14:35:34.88: [ 1955]: --> [7:CONNECT]
> > Sep 05 14:35:34.88: [ 1955]: SEND begin page
> > Sep 05 14:35:43.41: [ 1955]: SENT 17591 bytes of data
> > Sep 05 14:35:43.41: [ 1955]: SEND 1D RTC
> > Sep 05 14:35:43.41: [ 1955]: SEND end page
> > Sep 05 14:35:43.41: [ 1955]: SEND send MPS (more pages, same document)
> > Sep 05 14:35:59.78: [ 1955]: --> [7:+FHS:52]
> > Sep 05 14:35:59.78: [ 1955]: REMOTE HANGUP: No response to MPS repeated 3 times (code 52)
> > Sep 05 14:35:59.78: [ 1955]: SEND: No response to MPS repeated 3 times; Giving up after 3 attempts to send same page "docq/doc157.ps;00", dirnum 0
> > Sep 05 14:35:59.78: [ 1955]: <-- [5:ATH0\r]
> > Sep 05 14:35:59.91: [ 1955]: --> [2:OK]
> > Sep 05 14:35:59.91: [ 1955]: MODEM set DTR OFF
> > Sep 05 14:35:59.91: [ 1955]: SESSION END
> >
>
> ____________________ HylaFAX(tm) Users Mailing List _______________________
> To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
--
HAGOS eG phone: +49 711 7880592
Matthias Reich fax: +49 711 7880599
Industriestr. 62 web: http://www.hagos.de
D-70565 Stuttgart mail: rei@hagos.de
Germany
----------------------------------------------------------------------------
Be careful your mail is read by the NSA too !!
____________________ HylaFAX(tm) Users Mailing List _______________________
To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
