|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Problem sending empty pages (elsa 56k internet)
Hi,
I am having trouble with the configuration of an elsa 56k internet
modem.
I use the elsa-config file from their website (v250), but it still does
not work out.
After the modem establishes a connection with the fax machine, it will
stop the connection after about 10 seconds, and an empty page will
appear on the external fax.
I am using SuSE 6.4 with all the Upgrades from the Suse site (tiff
3.4.0, libtiff 3.4.0, hylafax 4.1b135)
I added my modem log and conf.ttyS0
Any help and suggestions is/are welcome
Tilmann Kuemmel
Here is my modem log:
Aug 21 19:14:13.80: [ 854]: SESSION BEGIN 00000011 492319309331
Aug 21 19:14:13.80: [ 854]: SEND FAX: JOB 25 DEST 9309331 COMMID
00000011
Aug 21 19:14:13.80: [ 854]: MODEM set DTR OFF
Aug 21 19:14:16.39: [ 854]: MODEM set DTR ON
Aug 21 19:14:16.40: [ 854]: MODEM set baud rate: 115200 baud, input
flow RTS/CTS, output flow RTS/CTS
Aug 21 19:14:16.40: [ 854]: MODEM flush i/o
Aug 21 19:14:16.40: [ 854]: <-- [16:ATX3E0V1Q0S0=0H\r]
Aug 21 19:14:16.48: [ 854]: --> [2:OK]
Aug 21 19:14:16.48: [ 854]: <-- [27:ATS8=2S7=60+IFC=2,2;&D2&C1\r]
Aug 21 19:14:16.58: [ 854]: --> [2:OK]
Aug 21 19:14:16.58: [ 854]: <-- [14:AT+FCLASS=2.0\r]
Aug 21 19:14:16.62: [ 854]: --> [2:OK]
Aug 21 19:14:16.62: [ 854]: <-- [9:AT+FLO=2\r]
Aug 21 19:14:16.66: [ 854]: --> [2:OK]
Aug 21 19:14:16.66: [ 854]: <-- [9:AT+FPP=0\r]
Aug 21 19:14:16.70: [ 854]: --> [2:OK]
Aug 21 19:14:16.70: [ 854]: <-- [9:AT+FBO=0\r]
Aug 21 19:14:16.74: [ 854]: --> [2:OK]
Aug 21 19:14:16.74: [ 854]: <-- [10:AT+FCT=30\r]
Aug 21 19:14:16.78: [ 854]: --> [2:OK]
Aug 21 19:14:16.78: [ 854]: <-- [15:AT+FNR=1,1,1,1\r]
Aug 21 19:14:16.83: [ 854]: --> [2:OK]
Aug 21 19:14:16.83: [ 854]: <-- [7:AT+FAP\r]
Aug 21 19:14:16.87: [ 854]: --> [5:ERROR]
Aug 21 19:14:16.87: [ 854]: MODEM Command error
Aug 21 19:14:16.87: [ 854]: <-- [9:AT+FIE=0\r]
Aug 21 19:14:16.91: [ 854]: --> [2:OK]
Aug 21 19:14:16.91: [ 854]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Aug 21 19:14:16.95: [ 854]: --> [2:OK]
Aug 21 19:14:16.95: [ 854]: <-- [7:ATL3M1\r]
Aug 21 19:14:17.00: [ 854]: --> [2:OK]
Aug 21 19:14:17.00: [ 854]: MODEM input buffering enabled
Aug 21 19:14:17.01: [ 854]: <-- [14:AT+FCLASS=2.0\r]
Aug 21 19:14:17.15: [ 854]: --> [2:OK]
Aug 21 19:14:17.15: [ 854]: <-- [9:AT+FLO=2\r]
Aug 21 19:14:17.29: [ 854]: --> [2:OK]
Aug 21 19:14:17.29: [ 854]: <-- [9:AT+FPP=0\r]
Aug 21 19:14:17.43: [ 854]: --> [2:OK]
Aug 21 19:14:17.43: [ 854]: <-- [9:AT+FBO=0\r]
Aug 21 19:14:17.57: [ 854]: --> [2:OK]
Aug 21 19:14:17.57: [ 854]: <-- [10:AT+FCT=30\r]
Aug 21 19:14:17.71: [ 854]: --> [2:OK]
Aug 21 19:14:17.71: [ 854]: <-- [15:AT+FNR=1,1,1,1\r]
Aug 21 19:14:17.85: [ 854]: --> [2:OK]
Aug 21 19:14:17.85: [ 854]: <-- [7:AT+FAP\r]
Aug 21 19:14:17.99: [ 854]: --> [5:ERROR]
Aug 21 19:14:17.99: [ 854]: MODEM Command error
Aug 21 19:14:17.99: [ 854]: <-- [9:AT+FIE=0\r]
Aug 21 19:14:18.13: [ 854]: --> [2:OK]
Aug 21 19:14:18.13: [ 854]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Aug 21 19:14:18.27: [ 854]: --> [2:OK]
Aug 21 19:14:18.27: [ 854]: <-- [17:AT+FLI="+49.241"\r]
Aug 21 19:14:18.41: [ 854]: --> [2:OK]
Aug 21 19:14:18.42: [ 854]: <-- [13:ATDTW9309331\r]
Aug 21 19:14:38.67: [ 854]: --> [4:+FCO]
Aug 21 19:14:40.88: [ 854]: --> [29:+FNF: AD 00 36 40 80 C4 01 E4]
Aug 21 19:14:40.88: [ 854]: --> [27:+FCI:" 0231 930 9331"]
Aug 21 19:14:40.88: [ 854]: --> [22:+FIS:1,3,0,2,1,1,0,4,0]
Aug 21 19:14:40.88: [ 854]: --> [2:OK]
Aug 21 19:14:40.89: [ 854]: <-- [23:AT+FIS=0,3,0,2,0,0,0,4\r]
Aug 21 19:14:41.03: [ 854]: --> [2:OK]
Aug 21 19:14:41.03: [ 854]: <-- [7:AT+FDT\r]
Aug 21 19:14:46.63: [ 854]: --> [22:+FCS:0,3,0,2,0,0,0,5,0]
Aug 21 19:14:46.94: [ 854]: --> [7:CONNECT]
Aug 21 19:14:46.95: [ 854]: <-- data [923]
Aug 21 19:14:46.95: [ 854]: <-- data [9]
Aug 21 19:14:46.95: [ 854]: <-- data [2]
Aug 21 19:14:54.02: [ 854]: --> [7:+FHS:00]
Aug 21 19:14:54.03: [ 854]: <-- [4:ATH\r]
Aug 21 19:14:54.03: [ 854]: --> [2:OK]
Aug 21 19:14:54.03: [ 854]: MODEM set DTR OFF
Aug 21 19:14:54.03: [ 854]: SESSION END
and my conf.ttyS0 file:
#
# Class 2.0 modem configuration for ELSA Modems with V.250 command set.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode: 49
AreaCode: 231
FAXNumber: +49.231.123456
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules
ServerTracing: 13
SessionTracing: 13
RecvFileMode: 0644
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: HIGH
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "+49.241"
LogFacility: local7
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "Von %%l|%c|Seite %%p von %%t"
PercentGoodLines: 80
MaxConsecutiveBadLines: 20
MaxRecvPages: 250
ModemPriority: 200
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2.0 # use this to supply a hint
ModemRate: 115200 # max rate for DCE-DTE
communication
ModemFlowControl: rtscts # XON/XOFF flow control assumed
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier
(or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd: ATDTW%s
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds: ATX3 # stuff to do when modem is
reset
ModemAnswerCmd: ATA # use this to answer phone
ModemNoFlowCmd: AT+IFC=0,0;
ModemHardFlowCmd: AT+IFC=2,2;
ModemSoftFlowCmd: AT+IFC=1,1;
ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd: ATE0 # disable command echo
ModemVerboseResultsCmd: ATV1 # enable verbose command results
ModemResultCodesCmd: ATQ0 # enable result codes
ModemOnHookCmd: ATH # place phone on hook (hangup)
ModemSoftResetCmd: ATZ # do soft reset of modem
ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
ModemRecvFillOrder: LSB2MSB # bit order of received
facsimile
ModemSendFillOrder: LSB2MSB # bit order modem expects for
transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0
Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D
(direct)
Class2CQCmd: "" # commands to enable copy
quality proc.
Class2AbortCmd: AT+FKS # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality
capabilities
Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities
Class2TBCCmd: AT+FPP=0 # setup stream mode
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FCT=30 # set phase C timeout parameter
Class2BUGCmd: AT+FBU=1 # enable HDLC frame tracing
Class2LIDCmd: AT+FLI # set local identifier command
Class2DCCCmd: AT+FCC # set modem capabilities command
Class2DISCmd: AT+FIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command
hack
Class2CIGCmd: AT+FPI # set polling identifier command
Class2NRCmd: AT+FNR=1,1,1,1 # setup status reporting command
Class2PIECmd: AT+FIE=0 # disable interrupt-enable
command
Class2PTSCmd: AT+FPS # set post-page status command
Class2SPLCmd: AT+FSP # set polling indicator command
Class2NFLOCmd: AT+FLO=0 # set no flow control command
Class2SFLOCmd: AT+FLO=1 # set software flow control
command
Class2HFLOCmd: AT+FLO=2 # set hardware flow control
command
Aug 21 19:14:13.80: [ 854]: SESSION BEGIN 00000011 492319309331
Aug 21 19:14:13.80: [ 854]: SEND FAX: JOB 25 DEST 9309331 COMMID 00000011
Aug 21 19:14:13.80: [ 854]: MODEM set DTR OFF
Aug 21 19:14:16.39: [ 854]: MODEM set DTR ON
Aug 21 19:14:16.40: [ 854]: MODEM set baud rate: 115200 baud, input flow RTS/CTS, output flow RTS/CTS
Aug 21 19:14:16.40: [ 854]: MODEM flush i/o
Aug 21 19:14:16.40: [ 854]: <-- [16:ATX3E0V1Q0S0=0H\r]
Aug 21 19:14:16.48: [ 854]: --> [2:OK]
Aug 21 19:14:16.48: [ 854]: <-- [27:ATS8=2S7=60+IFC=2,2;&D2&C1\r]
Aug 21 19:14:16.58: [ 854]: --> [2:OK]
Aug 21 19:14:16.58: [ 854]: <-- [14:AT+FCLASS=2.0\r]
Aug 21 19:14:16.62: [ 854]: --> [2:OK]
Aug 21 19:14:16.62: [ 854]: <-- [9:AT+FLO=2\r]
Aug 21 19:14:16.66: [ 854]: --> [2:OK]
Aug 21 19:14:16.66: [ 854]: <-- [9:AT+FPP=0\r]
Aug 21 19:14:16.70: [ 854]: --> [2:OK]
Aug 21 19:14:16.70: [ 854]: <-- [9:AT+FBO=0\r]
Aug 21 19:14:16.74: [ 854]: --> [2:OK]
Aug 21 19:14:16.74: [ 854]: <-- [10:AT+FCT=30\r]
Aug 21 19:14:16.78: [ 854]: --> [2:OK]
Aug 21 19:14:16.78: [ 854]: <-- [15:AT+FNR=1,1,1,1\r]
Aug 21 19:14:16.83: [ 854]: --> [2:OK]
Aug 21 19:14:16.83: [ 854]: <-- [7:AT+FAP\r]
Aug 21 19:14:16.87: [ 854]: --> [5:ERROR]
Aug 21 19:14:16.87: [ 854]: MODEM Command error
Aug 21 19:14:16.87: [ 854]: <-- [9:AT+FIE=0\r]
Aug 21 19:14:16.91: [ 854]: --> [2:OK]
Aug 21 19:14:16.91: [ 854]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Aug 21 19:14:16.95: [ 854]: --> [2:OK]
Aug 21 19:14:16.95: [ 854]: <-- [7:ATL3M1\r]
Aug 21 19:14:17.00: [ 854]: --> [2:OK]
Aug 21 19:14:17.00: [ 854]: MODEM input buffering enabled
Aug 21 19:14:17.01: [ 854]: <-- [14:AT+FCLASS=2.0\r]
Aug 21 19:14:17.15: [ 854]: --> [2:OK]
Aug 21 19:14:17.15: [ 854]: <-- [9:AT+FLO=2\r]
Aug 21 19:14:17.29: [ 854]: --> [2:OK]
Aug 21 19:14:17.29: [ 854]: <-- [9:AT+FPP=0\r]
Aug 21 19:14:17.43: [ 854]: --> [2:OK]
Aug 21 19:14:17.43: [ 854]: <-- [9:AT+FBO=0\r]
Aug 21 19:14:17.57: [ 854]: --> [2:OK]
Aug 21 19:14:17.57: [ 854]: <-- [10:AT+FCT=30\r]
Aug 21 19:14:17.71: [ 854]: --> [2:OK]
Aug 21 19:14:17.71: [ 854]: <-- [15:AT+FNR=1,1,1,1\r]
Aug 21 19:14:17.85: [ 854]: --> [2:OK]
Aug 21 19:14:17.85: [ 854]: <-- [7:AT+FAP\r]
Aug 21 19:14:17.99: [ 854]: --> [5:ERROR]
Aug 21 19:14:17.99: [ 854]: MODEM Command error
Aug 21 19:14:17.99: [ 854]: <-- [9:AT+FIE=0\r]
Aug 21 19:14:18.13: [ 854]: --> [2:OK]
Aug 21 19:14:18.13: [ 854]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Aug 21 19:14:18.27: [ 854]: --> [2:OK]
Aug 21 19:14:18.27: [ 854]: <-- [17:AT+FLI="+49.241"\r]
Aug 21 19:14:18.41: [ 854]: --> [2:OK]
Aug 21 19:14:18.42: [ 854]: <-- [13:ATDTW9309331\r]
Aug 21 19:14:38.67: [ 854]: --> [4:+FCO]
Aug 21 19:14:40.88: [ 854]: --> [29:+FNF: AD 00 36 40 80 C4 01 E4]
Aug 21 19:14:40.88: [ 854]: --> [27:+FCI:" 0231 930 9331"]
Aug 21 19:14:40.88: [ 854]: --> [22:+FIS:1,3,0,2,1,1,0,4,0]
Aug 21 19:14:40.88: [ 854]: --> [2:OK]
Aug 21 19:14:40.89: [ 854]: <-- [23:AT+FIS=0,3,0,2,0,0,0,4\r]
Aug 21 19:14:41.03: [ 854]: --> [2:OK]
Aug 21 19:14:41.03: [ 854]: <-- [7:AT+FDT\r]
Aug 21 19:14:46.63: [ 854]: --> [22:+FCS:0,3,0,2,0,0,0,5,0]
Aug 21 19:14:46.94: [ 854]: --> [7:CONNECT]
Aug 21 19:14:46.95: [ 854]: <-- data [923]
Aug 21 19:14:46.95: [ 854]: <-- data [9]
Aug 21 19:14:46.95: [ 854]: <-- data [2]
Aug 21 19:14:54.02: [ 854]: --> [7:+FHS:00]
Aug 21 19:14:54.03: [ 854]: <-- [4:ATH\r]
Aug 21 19:14:54.03: [ 854]: --> [2:OK]
Aug 21 19:14:54.03: [ 854]: MODEM set DTR OFF
Aug 21 19:14:54.03: [ 854]: SESSION END
