[hylafax-users] Re: Xircom CEM56(Class2) Call aborted, from +FK or <CAN> (code 2)

[Dmitry Bely <dbely@mail.ru>]

Darren Nickerson <darren@dazza.org> writes:

> Folks,
> 
> In the spirit of getting HylaFAX flying with more modems, I decided to tackle 
> the Class2 fax capability of my laptop's Xircom CEM56 10/100 Ethernet, 56.6 
> KBps modem combo card. The card claims Hayes compliance, but does not document 
> its fax commands, so I based my current config upon the PPIs.

What is the PPI?

>  Things go very 
> well indeed until the end of the transmission,
> 
> Jun 08 12:13:46.24: [16528]: SEND send MPS (more pages, same document)
> Jun 08 12:13:46.24: [16528]: <-- [9:AT+FET=0\r]
> Jun 08 12:13:49.63: [16528]: --> [7:+FPTS:1]
> Jun 08 12:13:49.63: [16528]: --> [2:OK]
> Jun 08 12:13:49.63: [16528]: SEND recv MCF (message confirmation)
> Jun 08 12:13:49.63: [16528]: SEND FAX (00000047): FROM darren@dazza.org TO 
> +12152438335 (page 1 of 2 sent in 0:17)
> Jun 08 12:13:49.63: [16528]: SEND FAX (00000047): FROM darren@dazza.org TO 
> +12152438335 (docq/doc23.ps;31 sent in 0:17)
> Jun 08 12:13:49.64: [16528]: SEND file "docq/doc24.ps;31"
> Jun 08 12:13:49.64: [16528]: USE page width 1728 pixels in 215 mm
> Jun 08 12:13:49.64: [16528]: USE unlimited page length 
> Jun 08 12:13:49.64: [16528]: USE 7.7 line/mm
> Jun 08 12:13:49.64: [16528]: USE 1-D MR
> Jun 08 12:13:49.64: [16528]: <-- [7:AT+FDT\r]
> Jun 08 12:13:49.82: [16528]: --> [7:CONNECT]
> Jun 08 12:13:49.82: [16528]: SEND wait for XON
> Jun 08 12:13:49.82: [16528]: --> [1:]
> Jun 08 12:13:49.82: [16528]: SEND begin page
> Jun 08 12:13:49.83: [16528]: <-- data [1027]
> Jun 08 12:13:49.83: [16528]: <-- data [821]
> Jun 08 12:13:49.83: [16528]: SENT 1845 bytes of data
> Jun 08 12:13:49.83: [16528]: SEND 1D RTC

Oh, no ... :-) I realize that you use Hylafax without my patches, but even
then Hylafax does *not* send RTC in Class 2 by default
(Class2SendRTC=no). Have you enabled it your config.modem???

> Jun 08 12:13:49.83: [16528]: <-- data [9]
> Jun 08 12:13:49.83: [16528]: <-- data [2]
> Jun 08 12:13:49.83: [16528]: SEND end page
> Jun 08 12:13:50.70: [16528]: --> [2:OK]
> Jun 08 12:13:50.70: [16528]: SEND send EOP (no more pages or documents)
> Jun 08 12:13:50.70: [16528]: <-- [9:AT+FET=2\r]
> Jun 08 12:13:54.08: [16528]: --> [7:+FPTS:1]
> Jun 08 12:13:54.08: [16528]: SEND recv MCF (message confirmation)
> Jun 08 12:13:54.08: [16528]: SEND FAX (00000047): FROM darren@dazza.org TO 
> +12152438335 (page 2 of 2 sent in 0:05)
> Jun 08 12:13:54.08: [16528]: SEND FAX (00000047): FROM darren@dazza.org TO 
> +12152438335 (docq/doc24.ps;31 sent in 0:05)

Hmm, looks like that we have to wait for "OK" after "AT+FET=2"
(people who own EIA/TIA-592, can you check this?) Just another
Hylafax bug?

> Jun 08 12:13:54.09: [16528]: <-- [5:ATH0\r]
> Jun 08 12:13:54.19: [16528]: --> [7:+FHNG:2]
> Jun 08 12:13:54.19: [16528]: REMOTE HANGUP: Call aborted,  from +FK or <CAN> 
> (code 2)
> Jun 08 12:13:55.19: [16528]: --> [2:OK]
> Jun 08 12:13:55.19: [16528]: MODEM set DTR OFF
> Jun 08 12:13:55.19: [16528]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
> Jun 08 12:13:55.19: [16528]: SESSION END
> 
> 
> Looks like a big delay between 
> 
> Jun 08 12:13:50.70: [16528]: <-- [9:AT+FET=2\r]
> Jun 08 12:13:54.08: [16528]: --> [7:+FPTS:1]

3.4 seconds? Pretty normal.

> Does anyone with class2 specs have any insight into what's going on here? I've 
> attached the entire session log FYI.

Hope to hear from you soon,
Dmitry




____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null