[hylafax-users] Not even Tiff/F format ges sent ok... (some more data)

To: hylafax-users@hylafax.org
Subject: [hylafax-users] Not even Tiff/F format ges sent ok... (some more data)
From: Borut Kurnik <borut.kurnik@ADD.SI>
Date: Thu, 8 Jun 2000 20:24:46 +0100

Hello!

I'd really appreciate if You could  take a few moments of your time  to
take a look at this.

Even if I have pure Tiff/F format already or the fax server creates it
in the
process, when i give it a text file, the result is the same (I only
receive upper
halfs of the letters in first line of text, as i mentioned).

>From the WHFC client I even get nothing, although the document gets to
the  server side converted from eig.: MS WORD to postscript correctly.

I checked all the documents after the conversion in the  './docq'
directory.   Everything looks just fine.

I tried hw and sw flow control and results are the same
(ModemFlowControl  in
config.modem      =>   /dev/modem)

 Using pentium II,   Modem: USR 56K  Voice Faxmodem

System: RedHat Linux 6.2
Hylafax: tried on 4.0 and 4.1 beta, but get the sam results.
Fonts: ghostscript 5.10.7 standard and 5.10.6 other

The attached log was made with  SessionTracing:   0x097FF

Hope that will help You a bit.

Thanks

Borut





Jun 08 20:45:32.22: [ 1671]: SESSION BEGIN 00000065 10137
Jun 08 20:45:32.22: [ 1671]: SEND FAX: JOB 105 DEST 37 COMMID 00000065
Jun 08 20:45:32.22: [ 1671]: MODEM set DTR OFF
Jun 08 20:45:32.22: [ 1671]: DELAY 2600 ms
Jun 08 20:45:34.81: [ 1671]: MODEM set DTR ON
Jun 08 20:45:34.81: [ 1671]: MODEM set baud rate: 19200 baud, input flow
RTS/CTS, output flow RTS/CTS
Jun 08 20:45:34.81: [ 1671]: MODEM flush i/o
Jun 08 20:45:34.81: [ 1671]: <-- [15:ATE0V1Q0S0=0H0\r]
Jun 08 20:45:34.95: [ 1671]: --> [2:OK]
Jun 08 20:45:34.95: [ 1671]: <-- [15:ATS8=2S7=60&H1\r]
Jun 08 20:45:35.09: [ 1671]: --> [2:OK]
Jun 08 20:45:35.09: [ 1671]: <-- [12:AT+FCLASS=1\r]
Jun 08 20:45:35.23: [ 1671]: --> [2:OK]
Jun 08 20:45:35.23: [ 1671]: <-- [5:ATM0\r]
Jun 08 20:45:35.37: [ 1671]: --> [2:OK]
Jun 08 20:45:35.37: [ 1671]: STATE CHANGE: RUNNING -> SENDING
Jun 08 20:45:35.37: [ 1671]: MODEM input buffering enabled
Jun 08 20:45:35.37: [ 1671]: <-- [12:AT+FCLASS=1\r]
Jun 08 20:45:35.61: [ 1671]: --> [2:OK]
Jun 08 20:45:35.62: [ 1671]: DIAL 37
Jun 08 20:45:35.62: [ 1671]: <-- [7:ATDT37\r]
Jun 08 20:45:49.00: [ 1671]: --> [7:CONNECT]
Jun 08 20:45:49.00: [ 1671]: MODEM input buffering disabled
Jun 08 20:45:50.80: [ 1671]: --> HDLC<41:FF C0 04 00 00 88 01 00 51 92
08 82 22 22 04 26 74 F6 74 F6 74 04 32 52 42 04 CA 00 F2 00 01 01 1B 71
80 80 80 80 20 36 2A>
Jun 08 20:45:50.80: [ 1671]: --> [2:OK]
Jun 08 20:45:50.80: [ 1671]: <-- [9:AT+FRH=3\r]
Jun 08 20:45:50.82: [ 1671]: --> [7:CONNECT]
Jun 08 20:45:51.49: [ 1671]: --> HDLC<25:FF C0 02 EC CC 0C 0C 9C EC 8C
04 8C 6C 04 6C 1C CC D4 04 04 04 04 04 A1 B7>
Jun 08 20:45:51.49: [ 1671]: --> [2:OK]
Jun 08 20:45:51.49: [ 1671]: REMOTE CSI "+386 61 1790037"
Jun 08 20:45:51.49: [ 1671]: <-- [9:AT+FRH=3\r]
Jun 08 20:45:51.51: [ 1671]: --> [7:CONNECT]
Jun 08 20:45:51.76: [ 1671]: --> HDLC<9:FF C8 01 00 77 15 22 17 5D>
Jun 08 20:45:51.76: [ 1671]: --> [2:OK]
Jun 08 20:45:51.76: [ 1671]: REMOTE best rate 14400 bit/s
Jun 08 20:45:51.76: [ 1671]: REMOTE max page width 1728 pixels in 215 mm

Jun 08 20:45:51.76: [ 1671]: REMOTE max unlimited page length
Jun 08 20:45:51.76: [ 1671]: REMOTE best vres 7.7 line/mm
Jun 08 20:45:51.76: [ 1671]: REMOTE best format 2-D MMR
Jun 08 20:45:51.76: [ 1671]: REMOTE supports T.30 Annex A, ECM
Jun 08 20:45:51.76: [ 1671]: REMOTE best 10 ms/scanline
Jun 08 20:45:51.76: [ 1671]: USE 14400 bit/s
Jun 08 20:45:51.76: [ 1671]: USE 10 ms/scanline
Jun 08 20:45:51.76: [ 1671]: SEND file "docq/doc107.ps;31"
Jun 08 20:45:51.76: [ 1671]: USE page width 1728 pixels in 215 mm
Jun 08 20:45:51.76: [ 1671]: USE unlimited page length
Jun 08 20:45:51.76: [ 1671]: USE 7.7 line/mm
Jun 08 20:45:51.76: [ 1671]: USE 1-D MR
Jun 08 20:45:51.76: [ 1671]: SEND training at v.17 14400 bit/s
Jun 08 20:45:51.76: [ 1671]: <-- [9:AT+FTH=3\r]
Jun 08 20:45:51.96: [ 1671]: --> [7:CONNECT]
Jun 08 20:45:51.96: [ 1671]: <-- HDLC<23:FF C0 C2 74 F6 74 F6 74 26 04
22 22 82 04 04 04 04 04 04 04 04 04 04>
Jun 08 20:45:51.96: [ 1671]: <-- data [23]
Jun 08 20:45:51.96: [ 1671]: <-- data [2]
Jun 08 20:45:51.99: [ 1671]: --> [7:CONNECT]
Jun 08 20:45:51.99: [ 1671]: <-- HDLC<6:FF C8 C1 00 46 14>
Jun 08 20:45:51.99: [ 1671]: <-- data [6]
Jun 08 20:45:51.99: [ 1671]: <-- data [2]
Jun 08 20:45:53.93: [ 1671]: --> [2:OK]
Jun 08 20:45:53.93: [ 1671]: DELAY 75 ms
Jun 08 20:45:54.01: [ 1671]: <-- [11:AT+FTM=145\r]
Jun 08 20:45:55.49: [ 1671]: --> [7:CONNECT]
Jun 08 20:45:55.49: [ 1671]: <-- data [1024]
Jun 08 20:45:55.49: [ 1671]: <-- data [1024]
Jun 08 20:45:55.49: [ 1671]: <-- data [652]
Jun 08 20:45:55.49: [ 1671]: <-- data [2]
Jun 08 20:45:57.02: [ 1671]: --> [2:OK]
Jun 08 20:45:57.02: [ 1671]: <-- [9:AT+FRH=3\r]
Jun 08 20:45:57.26: [ 1671]: --> [7:CONNECT]
Jun 08 20:45:58.29: [ 1671]: --> HDLC<5:FF C8 21 57 BE>
Jun 08 20:45:58.29: [ 1671]: --> [2:OK]
Jun 08 20:45:58.29: [ 1671]: TRAINING succeeded
Jun 08 20:45:58.29: [ 1671]: <-- [11:AT+FTM=146\r]
Jun 08 20:45:58.55: [ 1671]: --> [7:CONNECT]
Jun 08 20:45:58.55: [ 1671]: SEND begin page
Jun 08 20:45:58.56: [ 1671]: <-- data [1026]
Jun 08 20:45:58.56: [ 1671]: <-- data [1027]
Jun 08 20:45:58.56: [ 1671]: <-- data [1024]
Jun 08 20:45:58.56: [ 1671]: <-- data [1024]
Jun 08 20:45:58.56: [ 1671]: <-- data [316]
Jun 08 20:46:00.55: [ 1671]: SENT 4411 bytes of data
Jun 08 20:46:00.55: [ 1671]: SEND 1D RTC
Jun 08 20:46:00.55: [ 1671]: <-- data [29]
Jun 08 20:46:00.55: [ 1671]: <-- data [2]
Jun 08 20:46:00.55: [ 1671]: SEND end page
Jun 08 20:46:01.05: [ 1671]: --> [2:OK]
Jun 08 20:46:01.05: [ 1671]: DELAY 95 ms
Jun 08 20:46:01.15: [ 1671]: SEND send EOP (no more pages or documents)
Jun 08 20:46:01.15: [ 1671]: <-- [9:AT+FTH=3\r]
Jun 08 20:46:01.31: [ 1671]: --> [7:CONNECT]
Jun 08 20:46:01.31: [ 1671]: <-- HDLC<3:FF C8 F4>
Jun 08 20:46:01.31: [ 1671]: <-- data [3]
Jun 08 20:46:01.31: [ 1671]: <-- data [2]
Jun 08 20:46:02.48: [ 1671]: --> [2:OK]
Jun 08 20:46:02.48: [ 1671]: <-- [9:AT+FRH=3\r]
Jun 08 20:46:02.86: [ 1671]: --> [7:CONNECT]
Jun 08 20:46:03.72: [ 1671]: --> HDLC<5:FF C8 31 45 8F>
Jun 08 20:46:03.72: [ 1671]: --> [2:OK]
Jun 08 20:46:03.72: [ 1671]: SEND recv MCF (message confirmation)
Jun 08 20:46:03.72: [ 1671]: SEND FAX (00000065): FROM root@hasan.add.si
TO 37 (page 1 of 1 sent in 0:12)
Jun 08 20:46:03.72: [ 1671]: SEND FAX (00000065): FROM root@hasan.add.si
TO 37 (docq/doc107.ps;31 sent in 0:12)
Jun 08 20:46:03.72: [ 1671]: <-- [9:AT+FTH=3\r]
Jun 08 20:46:03.92: [ 1671]: --> [7:CONNECT]
Jun 08 20:46:03.92: [ 1671]: <-- HDLC<3:FF C8 DF>
Jun 08 20:46:03.92: [ 1671]: <-- data [3]
Jun 08 20:46:03.92: [ 1671]: <-- data [2]
Jun 08 20:46:05.10: [ 1671]: --> [2:OK]
Jun 08 20:46:05.10: [ 1671]: MODEM input buffering enabled
Jun 08 20:46:05.10: [ 1671]: <-- [5:ATH0\r]
Jun 08 20:46:05.34: [ 1671]: --> [2:OK]
Jun 08 20:46:05.34: [ 1671]: MODEM set DTR OFF
Jun 08 20:46:05.34: [ 1671]: STATE CHANGE: SENDING -> MODEMWAIT (timeout
5)
Jun 08 20:46:05.34: [ 1671]: SESSION END



  Borut Kurnik
  ADD, d.o.o.
          <borut.kurnik@add.si>
          Conference Software Address
          Default Directory Server

begin:vcard 
n:Kurnik;Borut
x-mozilla-html:FALSE
org:ADD, d.o.o.
adr:;;;;;;
version:2.1
email;internet:borut.kurnik@add.si
x-mozilla-cpt:;0
fn:Borut Kurnik
end:vcard

Follow-Ups:
- [hylafax-users] Re: Not even Tiff/F format ges sent ok... (some more data)
  - From: Dmitry Bely <dbely@mail.ru>

Prev by Date: [hylafax-users] Mailfax Gateway, which Rewriting rule should be use?
Next by Date: [hylafax-users] Xircom CEM56(Class2) Call aborted, from +FK or <CAN> (code 2)
Prev by thread: [hylafax-users] Re: Mailfax Gateway, which Rewriting rule should be use?
Next by thread: [hylafax-users] Re: Not even Tiff/F format ges sent ok... (some more data)
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services