|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Re: Remote sends 2 pages I get only one
Alvaro Rosales <alvaro@procacao.wintersperu.com.pe> writes:
> Hi fellows Im using Hylafax in a send and receive environment it works
> ok , but when someone sendme a fax with two or more pages ,(the sender
> doesnt get any error) I only get the first page , this is the log , I
> hope you can help me
Help you to do what? Change the remote fax machine settings? Hylafax just
was asked to interrupt transmission for the operator intervention (PRI-EOP
meaning according to T.30) -- and followed this directive. BTW, you logs is
almost useless at this tracing level: it's absolutely unclear which HDLC
frames were sent/received. So use in future SessionTracing=0x7ff,
if you are going to ask a fax protocol-related question.
> Jun 06 14:41:14.89: [ 656]: SESSION BEGIN 00000481 11260
> Jun 06 14:41:14.89: [ 656]: <-- [4:ATA\r]
> Jun 06 14:41:20.41: [ 656]: --> [7:CONNECT]
> Jun 06 14:41:20.41: [ 656]: ANSWER: FAX CONNECTION
> Jun 06 14:41:20.41: [ 656]: RECV FAX: begin
> Jun 06 14:41:20.41: [ 656]: <-- data [23]
> Jun 06 14:41:20.42: [ 656]: <-- data [2]
> Jun 06 14:41:22.10: [ 656]: --> [7:CONNECT]
> Jun 06 14:41:22.10: [ 656]: <-- data [10]
> Jun 06 14:41:22.10: [ 656]: <-- data [2]
> Jun 06 14:41:22.64: [ 656]: --> [2:OK]
> Jun 06 14:41:22.64: [ 656]: <-- [9:AT+FRH=3\r]
> Jun 06 14:41:23.04: [ 656]: --> [7:CONNECT]
> Jun 06 14:41:24.51: [ 656]: --> [2:OK]
> Jun 06 14:41:24.51: [ 656]: REMOTE TSI "5114700651"
> Jun 06 14:41:24.51: [ 656]: <-- [9:AT+FRH=3\r]
> Jun 06 14:41:24.53: [ 656]: --> [7:CONNECT]
> Jun 06 14:41:24.80: [ 656]: --> [2:OK]
> Jun 06 14:41:24.80: [ 656]: REMOTE wants 9600 bit/s
> Jun 06 14:41:24.80: [ 656]: REMOTE wants page width 1728 pixels in 215
> mm
> Jun 06 14:41:24.80: [ 656]: REMOTE wants unlimited page length
> Jun 06 14:41:24.80: [ 656]: REMOTE wants 3.85 line/mm
> Jun 06 14:41:24.80: [ 656]: REMOTE wants 1-D MR
> Jun 06 14:41:24.80: [ 656]: RECV training at v.29 9600 bit/s
> Jun 06 14:41:24.80: [ 656]: <-- [10:AT+FRM=96\r]
> Jun 06 14:41:25.16: [ 656]: --> [7:CONNECT]
> Jun 06 14:41:26.69: [ 656]: RECV: TCF 1820 bytes, 1% non-zero, 1781
> zero-run
> Jun 06 14:41:26.70: [ 656]: --> [10:NO CARRIER]
> Jun 06 14:41:26.70: [ 656]: DELAY 75 ms
> Jun 06 14:41:26.78: [ 656]: <-- [9:AT+FTH=3\r]
> Jun 06 14:41:26.83: [ 656]: --> [7:CONNECT]
> Jun 06 14:41:26.83: [ 656]: <-- data [3]
> Jun 06 14:41:26.83: [ 656]: <-- data [2]
> Jun 06 14:41:28.14: [ 656]: --> [2:OK]
> Jun 06 14:41:28.14: [ 656]: TRAINING succeeded
> Jun 06 14:41:28.14: [ 656]: <-- [10:AT+FRM=96\r]
> Jun 06 14:41:29.46: [ 656]: --> [7:CONNECT]
> Jun 06 14:41:29.46: [ 656]: RECV: begin page
> Jun 06 14:42:04.48: [ 656]: RECV: 1163 total lines, 0 bad lines, 0
> consecutive bad lines
> Jun 06 14:42:04.49: [ 656]: RECV: end page
> Jun 06 14:42:04.49: [ 656]: --> [10:NO CARRIER]
> Jun 06 14:42:04.49: [ 656]: <-- [9:AT+FRH=3\r]
> Jun 06 14:42:07.89: [ 656]: --> [7:CONNECT]
> Jun 06 14:42:08.85: [ 656]: --> [2:OK]
> Jun 06 14:42:08.85: [ 656]: RECV recv MPS (more pages, same document)
> Jun 06 14:42:08.85: [ 656]: <-- [9:AT+FTH=3\r]
> Jun 06 14:42:08.90: [ 656]: --> [7:CONNECT]
> Jun 06 14:42:08.90: [ 656]: <-- data [3]
> Jun 06 14:42:08.90: [ 656]: <-- data [2]
> Jun 06 14:42:10.22: [ 656]: --> [2:OK]
> Jun 06 14:42:10.22: [ 656]: RECV send MCF (message confirmation)
> Jun 06 14:42:10.22: [ 656]: RECV FAX (00000481): from 5114700651, page
> 1 in 0:42, INF, 3.85 line/mm, 1-D M
> R
> Jun 06 14:42:10.22: [ 656]: <-- [10:AT+FRM=96\r]
> Jun 06 14:42:11.54: [ 656]: --> [7:CONNECT]
> Jun 06 14:42:11.54: [ 656]: RECV: begin page
> Jun 06 14:42:44.36: [ 656]: RECV: 1165 total lines, 0 bad lines, 0
> consecutive bad lines
> Jun 06 14:42:44.37: [ 656]: RECV: end page
> Jun 06 14:42:44.37: [ 656]: --> [10:NO CARRIER]
> Jun 06 14:42:44.37: [ 656]: <-- [9:AT+FRH=3\r]
> Jun 06 14:42:44.76: [ 656]: --> [7:CONNECT]
> Jun 06 14:42:45.57: [ 656]: --> [2:OK]
> Jun 06 14:42:45.57: [ 656]: RECV recv PRI-EOP (no more pages after
> interrupt)
> Jun 06 14:42:45.57: [ 656]: <-- [9:AT+FTH=3\r]
> Jun 06 14:42:45.62: [ 656]: --> [7:CONNECT]
> Jun 06 14:42:45.62: [ 656]: <-- data [3]
> Jun 06 14:42:45.62: [ 656]: <-- data [2]
> Jun 06 14:42:46.94: [ 656]: --> [2:OK]
> Jun 06 14:42:46.94: [ 656]: RECV send MCF (message confirmation)
> Jun 06 14:42:46.94: [ 656]: RECV FAX (00000481): from 5114700651, page
> 2 in 0:36, INF, 3.85 line/mm, 1-D M
> R
> Jun 06 14:42:46.94: [ 656]: RECV FAX (00000481): recvq/fax00167.tif
> from 5114700651, route to <unspecified
> >, 2 pages in 1:26
> Jun 06 14:42:46.94: [ 656]: <-- [9:AT+FRH=3\r]
> Jun 06 14:42:47.34: [ 656]: --> [7:CONNECT]
> Jun 06 14:42:48.26: [ 656]: --> [2:OK]
> Jun 06 14:42:48.26: [ 656]: RECV FAX: bin/faxrcvd "recvq/fax00167.tif"
> "ttyS3" "00000481" ""
> Jun 06 14:42:48.87: [ 656]: RECV FAX: end
> Jun 06 14:42:48.87: [ 656]: SESSION END
Hope to hear from you soon,
Dmitry
____________________ HylaFAX(tm) Users Mailing List _______________________
To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
