RE: flexfax: GVC Modem and Phase B unspecified error(correction)

["Bernd Proissl" <news@proissl.de>]

Just a guess:

------[snip]-----
On Wed, May 10, Bernd Proissl wrote:

>
> There is a patch to run hylafax with libtiff3.5. (which comes with Suse
6.4)

I just made a hylafax.rpm with this patch and placed it to our
suse.com internal mirror. I think it would appear at ftp.suse.com in a
few hours.

ftp://ftp.suse.com/pub/suse_update/6.4/n1/hyla_tiffp.rpm

--
mit freundlichen Gruessen,

Carsten Hoeger  - SuSE Professional Services -

SuSE GmbH,   Schanzaeckerstr. 10,      90443 Nuernberg, Germany
Tel: +49-911-7405356 Mo-Fr 09-17.00,       Fax: +49-911-3206727
http://www.suse.de/de/support/prof/index.html
------[snip]-----

Bernd



> -----Original Message-----
> From: owner-flexfax@celestial.com [mailto:owner-flexfax@celestial.com]On
> Behalf Of Frank SCHNELL
> Sent: Tuesday, May 30, 2000 10:35 AM
> To: flexfax@sgi.com
> Subject: Re: flexfax: GVC Modem and Phase B unspecified
> error(correction)
>
>
> Sorry for the last post. Here is a hopefully readible log file.
> Frank
>
> >>> "Frank SCHNELL" <schnell@nacma.nato.int> 25-May-00 14:04:55 >>>
> Hi all,
>
> since a couple days I am trying to get HylaFax working on Intel hardware
> running SuSe 6.4 Linux distribution. HylaFax came precompiled within
> this distribution.
>
> The modem in use identifies itself as "GVC Rockwell 144DPI/KA1131-00"
>
> During HylaFax setup a modem configuration file 'gvc-288-2' was used.
>
> When using sendfax to send a postscript file to any of three fax
> receivers
> (standard fax machines, no fax modems on computers) I get an "Unspecified
> phase B error (code 20)" I did try to include the Class2DDISCmd
> string "AT+FDIS"
> to my config file but it still won't work. Below is the session
> log. Each session stops
> at the same point during connection negotiations. Might be
> someone can help.
>
> Thanks much for your time and effort
>
> Frank Schnell
>
>
> ========================== Session log ===================================
> May 25 10:16:57.51: [ 2488]: SESSION BEGIN 00000007 3227078777
> May 25 10:16:57.51: [ 2488]: SEND FAX: JOB 13 DEST 7078777 COMMID 00000007
> May 25 10:16:57.51: [ 2488]: DELAY 2600 ms
> May 25 10:17:00.11: [ 2488]: <-- [15:ATE0V1Q0S0=0H0\r]
> May 25 10:17:00.86: [ 2488]: --> [14:ATE0V1Q0S0=0H0]
> May 25 10:17:00.86: [ 2488]: --> [2:OK]
> May 25 10:17:00.86: [ 2488]: <-- [21:ATS8=2S7=60\Q3&D3&C1\r]
> May 25 10:17:00.98: [ 2488]: --> [2:OK]
> May 25 10:17:00.98: [ 2488]: <-- [12:AT+FCLASS=2\r]
> May 25 10:17:01.09: [ 2488]: --> [2:OK]
> May 25 10:17:01.09: [ 2488]: <-- [3:AT\r]
> May 25 10:17:01.10: [ 2488]: --> [2:OK]
> May 25 10:17:01.10: [ 2488]: <-- [10:AT+FBOR=0\r]
> May 25 10:17:01.11: [ 2488]: --> [2:OK]
> May 25 10:17:01.11: [ 2488]: <-- [3:AT\r]
> May 25 10:17:01.12: [ 2488]: --> [2:OK]
> May 25 10:17:01.12: [ 2488]: <-- [24:AT+FDCC=1,5,2,2,1,0,0,0\r]
> May 25 10:17:01.14: [ 2488]: --> [2:OK]
> May 25 10:17:01.14: [ 2488]: <-- [5:ATM0\r]
> May 25 10:17:01.15: [ 2488]: --> [2:OK]
> May 25 10:17:01.15: [ 2488]: <-- [12:AT+FCLASS=2\r]
> May 25 10:17:01.26: [ 2488]: --> [2:OK]May 25 10:17:01.26:

> 2488]: <-- [3:AT\r]
> May 25 10:17:01.37: [ 2488]: --> [2:OK]
> May 25 10:17:01.37: [ 2488]: <-- [10:AT+FBOR=0\r]
> May 25 10:17:01.48: [ 2488]: --> [2:OK]
> May 25 10:17:01.48: [ 2488]: <-- [3:AT\r]
> May 25 10:17:01.59: [ 2488]: --> [2:OK]
> May 25 10:17:01.59: [ 2488]: <-- [24:AT+FDCC=1,5,2,2,1,0,0,0\r]
> May 25 10:17:01.71: [ 2488]: --> [2:OK]
> May 25 10:17:01.71: [ 2488]: <-- [16:AT+FLID="NACMA"\r]
> May 25 10:17:01.82: [ 2488]: --> [2:OK]
> May 25 10:17:01.82: [ 2488]: DIAL 7078777
> May 25 10:17:01.82: [ 2488]: <-- [16:ATL1M1DT7078777\r]
> May 25 10:17:29.38: [ 2488]: --> [5:+FCON]
> May 25 10:18:09.38: [ 2488]: REMOTE HANGUP: Unspecified Transmit
> Phase B error (code 20)
> May 25 10:18:09.38: [ 2488]: SEND FAILED: Unspecified Transmit
> Phase B error
> May 25 10:18:09.38: [ 2488]: <-- [5:ATH0\r]
> May 25 10:18:14.38: [ 2488]: MODEM <Timeout>
> May 25 10:18:14.38: [ 2488]: SESSION END
>
>
>
>
>
>
>
>