|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
5600ZDX Config file help
Hi,
I am trying to get my new Multitech 5600ZDX modem
(Firmware 241) to receive faxes properly. So far
I have tried a config file based on a Feb. 2000
exchange between Glenn Burkhardt and Mark J. Bailey but
to no avail.
My config file and a receive log follow below. Any
help gratefully appreciated!
BTW, this modem also uses mgetty and ppp for dialup access.
Thanks,
Kevin Tyle <kevin@meso.com>
MESO, Inc.
Troy, NY USA
--------CONFIG FILE-----------
# $Id: class2,v 1.2 1999/01/10 09:09:37 robert Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
# Generic Class 2 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode: 1
AreaCode: 518
FAXNumber: 1-999-999-9999
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: quiet
GettyArgs: "-r -b -s %s %l"
LocalIdentifier: "MESO, Inc."
TagLineFont: etc/lutRS18.pcf
TagLineFormat: ""
MaxRecvPages: 30
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2 # use this to supply a hint
ModemRate: 115200 # max rate for DCE-DTE communication
ModemFlowControl: xonxoff # XON/XOFF flow control assumed
ModemSetupDTRCmd: AT&D3 # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd: ATDT%s@ # T for tone dialing, @ for silence
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds: "" # stuff to do when modem is reset
#ModemAnswerCmd: ATA # use this to answer phone
#ModemNoFlowCmd: AT&K # disable flow control cmd
ModemHardFlowCmd: AT&E4&E13 # hardware flow control cmd
ModemSoftFlowCmd: AT&E5&E13 # software flow control cmd
#ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemSetVolumeCmd: "ATL0M1"
#ModemEchoOffCmd: ATE0 # disable command echo
#ModemVerboseResultsCmd: ATV1 # enable verbose command results
#ModemResultCodesCmd: ATQ0 # enable result codes
#ModemOnHookCmd: ATH0 # place phone on hook (hangup)
#ModemSoftResetCmd: ATZ # do soft reset of modem
#ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
#ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
#ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
#
# Configuration parameters for Class 2 modems.
#
Class2Cmd: AT+FCLASS=2 # command to enter class 2
Class2BORCmd: AT+FBOR=0 # bit order for phase B/C/D (direct)
Class2RELCmd: AT+FREL=1 # byte-align EOL codes on recv
Class2CQCmd: "" # commands to enable copy quality proc.
Class2AbortCmd: AT+FK # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities
Class2DCCQueryCmd: AT+FDCC=? # query for modem capabilities
Class2TBCCmd: AT+FTBC=0 # setup stream mode
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FPHCTO=30 # set phase C timeout parameter
Class2BUGCmd: AT+FBUG=1 # enable HDLC frame tracing
Class2LIDCmd: AT+FLID # set local identifier command
Class2DCCCmd: AT+FDCC # set modem capabilities command
Class2DISCmd: AT+FDIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command hack
Class2CIGCmd: AT+FCIG # set polling identifier command
Class2PTSCmd: AT+FPTS # set post-page status command
Class2SPLCmd: AT+FSPL # set polling indicator command
#
# If Class2RecvDataTrigger is not set, then it is set to DC1
#
Class2RecvDataTrigger: "" # character sent to modem to start recv
Class2XmitWaitForXON: yes # if true, wait for XON before send
--------------------RECEIVE LOG ------------------------------------------
May 16 16:37:25.84: [ 4858]: SESSION BEGIN 00000124 19999999999
May 16 16:37:25.84: [ 4858]: <-- [4:ATA\r]
May 16 16:37:34.92: [ 4858]: --> [5:+FCON]
May 16 16:37:34.92: [ 4858]: ANSWER: FAX CONNECTION
May 16 16:37:34.92: [ 4858]: RECV FAX: begin
May 16 16:37:36.44: [ 4858]: --> [29:+FTSI: "MESO/SkyBit A "]
May 16 16:37:36.44: [ 4858]: REMOTE TSI "MESO/SkyBit A "
May 16 16:37:36.82: [ 4858]: --> [22:+FDCS: 0,5,0,2,0,0,0,0]
May 16 16:37:36.82: [ 4858]: REMOTE wants 14400 bit/s
May 16 16:37:36.82: [ 4858]: REMOTE wants page width 1728 pixels in 215 mm
May 16 16:37:36.82: [ 4858]: REMOTE wants unlimited page length
May 16 16:37:36.82: [ 4858]: REMOTE wants 3.85 line/mm
May 16 16:37:36.82: [ 4858]: REMOTE wants 1-D MR
May 16 16:37:36.93: [ 4858]: --> [2:OK]
May 16 16:37:36.93: [ 4858]: <-- [7:AT+FDR\r]
May 16 16:37:39.82: [ 4858]: --> [5:+FCFR]
May 16 16:37:42.55: [ 4858]: --> [22:+FDCS: 0,5,0,2,0,0,0,0]
May 16 16:37:42.55: [ 4858]: REMOTE wants 14400 bit/s
May 16 16:37:42.55: [ 4858]: REMOTE wants page width 1728 pixels in 215 mm
May 16 16:37:42.55: [ 4858]: REMOTE wants unlimited page length
May 16 16:37:42.55: [ 4858]: REMOTE wants 3.85 line/mm
May 16 16:37:42.55: [ 4858]: REMOTE wants 1-D MR
May 16 16:37:42.55: [ 4858]: --> [7:CONNECT]
May 16 16:37:42.55: [ 4858]: RECV: begin page
May 16 16:37:42.55: [ 4858]: RECV: send trigger 021
May 16 16:37:42.55: [ 4858]: <-- data [1]
May 16 16:38:02.10: [ 4858]: RECV: 0 total lines, 0 bad lines, 0 consecutive bad lines
May 16 16:38:02.10: [ 4858]: --> [17:+FPTS: 1,2219,0,0]
May 16 16:38:03.46: [ 4858]: --> [7:+FET: 2]
May 16 16:38:03.46: [ 4858]: RECV recv EOP (no more pages or documents)
May 16 16:38:03.46: [ 4858]: --> [2:OK]
May 16 16:38:03.46: [ 4858]: RECV send MCF (message confirmation)
May 16 16:38:03.46: [ 4858]: RECV FAX (00000124): from MESO/SkyBit A 518283, page 1 in 0:27, INF, 3.85 line/mm, 1-D MR
May 16 16:38:03.46: [ 4858]: RECV FAX (00000124): recvq/fax00024.tif from MESO/SkyBit A , route to <unspecified>, 1 pages in 0:29
May 16 16:38:03.46: [ 4858]: <-- [7:AT+FDR\r]
May 16 16:38:06.03: [ 4858]: --> [8:+FHNG: 0]
May 16 16:38:06.03: [ 4858]: REMOTE HANGUP: Normal and proper end of connection (code 0)
May 16 16:38:06.03: [ 4858]: RECV FAX: bin/faxrcvd "recvq/fax00024.tif" "ttyS0" "00000124" ""
May 16 16:38:06.34: [ 4858]: RECV FAX: end
May 16 16:38:06.34: [ 4858]: SESSION END
