|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Dials dest but then dumps - RSPREC error/got DCN
I am using Hylafax v4.0pl2 with FreeBSD 3.4 & a USR Internal Faxmodem
Sending goes OK until
dump happens - sometimes it prints 2/3 of title page.
Any help would be appreciated for someone that understands the log.
My conf file first;
Thanks
CountryCode: 1
AreaCode: 416
FAXNumber: +1.999.555.1212
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing: 0xfffff
SessionTracing: 0xfffff
RecvFileMode: 0666
LogFileMode: 0666
DeviceMode: 0666
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "std.%s"
LocalIdentifier: "NothingSetup"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%p of %%t"
QualifyTSI: etc/tsi
MaxRecvPages: 25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2.0 # use this to supply a hint
ModemRate: 19200
ModemFlowControl: rtscts # XON/XOFF flow control assumed
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier
(or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd: ATDT%s@ # T for tone dialing, @ for
silence
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds: "" # stuff to do when modem is
reset
ModemAnswerCmd: ATA # use this to answer phone
ModemNoFlowCmd: AT&K # disable flow control cmd
ModemHardFlowCmd: AT&K3 # hardware flow control cmd
ModemSoftFlowCmd: AT&K4 # software flow control cmd
ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd: ATE0 # disable command echo
ModemVerboseResultsCmd: ATV1 # enable verbose command results
ModemResultCodesCmd: ATQ0 # enable result codes
ModemOnHookCmd: ATH0 # place phone on hook (hangup)
ModemSoftResetCmd: ATZ # do soft reset of modem
ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
ModemRecvFillOrder: LSB2MSB # bit order of received
facsimile
ModemSendFillOrder: LSB2MSB # bit order modem expects for
transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0
Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D
(direct)
Class2CQCmd: "" # commands to enable copy
quality proc.
Class2AbortCmd: AT+FKS # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality
capabilities
Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities
Class2TBCCmd: AT+FPP=0 # setup stream mode
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FCT=30 # set phase C timeout parameter
Class2BUGCmd: AT+FBU=1 # enable HDLC frame tracing
Class2LIDCmd: AT+FLI # set local identifier command
Class2DCCCmd: AT+FCC # set modem capabilities command
Class2DISCmd: AT+FIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command
hack
Class2CIGCmd: AT+FPI # set polling identifier command
Class2NRCmd: AT+FNR=1,1,1,1 # setup status reporting command
Class2PIECmd: AT+FIE=0 # disable interrupt-enable
command
Class2PTSCmd: AT+FPS # set post-page status command
Class2SPLCmd: AT+FSP # set polling indicator command
Class2NFLOCmd: AT+FLO=0 # set no flow control command
Class2SFLOCmd: AT+FLO=1 # set software flow control
command
Class2HFLOCmd: AT+FLO=2 # set hardware flow control
command
Here's the log!;
May 05 00:24:26.38: [ 440]: SESSION BEGIN 00000029 14162523608
May 05 00:24:26.38: [ 440]: SEND FAX: JOB 20 DEST 2523608 COMMID
00000029
May 05 00:24:26.38: [ 440]: MODEM set DTR OFF
May 05 00:24:26.38: [ 440]: DELAY 2600 ms
May 05 00:24:28.99: [ 440]: MODEM set DTR ON
May 05 00:24:31.99: [ 440]: MODEM set baud rate: 19200 baud, input flow
RTS/CTS,
output flow RTS/CTS
May 05 00:24:31.99: [ 440]: MODEM flush i/o
May 05 00:24:31.99: [ 440]: <-- [15:ATE0V1Q0S0=0H0\r]
May 05 00:24:32.13: [ 440]: --> [2:OK]
May 05 00:24:32.13: [ 440]: <-- [21:ATS8=2S7=60&K3&D2&C1\r]
May 05 00:24:32.27: [ 440]: --> [2:OK]
May 05 00:24:32.27: [ 440]: <-- [14:AT+FCLASS=2.0\r]
May 05 00:24:32.40: [ 440]: --> [2:OK]
May 05 00:24:32.40: [ 440]: <-- [9:AT+FLO=2\r]
May 05 00:24:32.54: [ 440]: --> [2:OK]
May 05 00:24:32.54: [ 440]: <-- [9:AT+FPP=0\r]
May 05 00:24:32.68: [ 440]: --> [2:OK]
May 05 00:24:32.68: [ 440]: <-- [9:AT+FBO=0\r]
May 05 00:24:32.82: [ 440]: --> [2:OK]
May 05 00:24:32.82: [ 440]: <-- [10:AT+FCT=30\r]
May 05 00:24:32.96: [ 440]: --> [2:OK]
May 05 00:24:32.96: [ 440]: <-- [15:AT+FNR=1,1,1,1\r]
May 05 00:24:33.10: [ 440]: --> [2:OK]
May 05 00:24:33.10: [ 440]: <-- [9:AT+FIE=0\r]
May 05 00:24:33.24: [ 440]: --> [2:OK]
May 05 00:24:33.24: [ 440]: <-- [9:AT+FBU=1\r]
May 05 00:24:33.38: [ 440]: --> [5:ERROR]
May 05 00:24:33.38: [ 440]: MODEM Command error
May 05 00:24:33.38: [ 440]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
May 05 00:24:33.52: [ 440]: --> [2:OK]
May 05 00:24:33.52: [ 440]: <-- [5:ATM0\r]
May 05 00:24:33.65: [ 440]: --> [2:OK]
May 05 00:24:33.65: [ 440]: STATE CHANGE: RUNNING -> SENDING
May 05 00:24:33.65: [ 440]: MODEM input buffering enabled
May 05 00:24:33.65: [ 440]: Apply DialString rules to "2523608"
May 05 00:24:33.65: [ 440]: --> return result "2523608"
May 05 00:24:33.65: [ 440]: <-- [14:AT+FCLASS=2.0\r]
May 05 00:24:33.89: [ 440]: --> [2:OK]
May 05 00:24:33.89: [ 440]: <-- [9:AT+FLO=2\r]
May 05 00:24:34.13: [ 440]: --> [2:OK]
May 05 00:24:34.13: [ 440]: <-- [9:AT+FPP=0\r]
May 05 00:24:34.37: [ 440]: --> [2:OK]
May 05 00:24:34.37: [ 440]: <-- [9:AT+FBO=0\r]
May 05 00:24:34.61: [ 440]: --> [2:OK]
May 05 00:24:34.61: [ 440]: <-- [10:AT+FCT=30\r]
May 05 00:24:34.85: [ 440]: --> [2:OK]
May 05 00:24:34.85: [ 440]: <-- [15:AT+FNR=1,1,1,1\r]
May 05 00:24:35.09: [ 440]: --> [2:OK]
May 05 00:24:35.09: [ 440]: <-- [9:AT+FIE=0\r]
May 05 00:24:35.33: [ 440]: --> [2:OK]
May 05 00:24:35.33: [ 440]: <-- [9:AT+FBU=1\r]
May 05 00:24:35.57: [ 440]: --> [5:ERROR]
May 05 00:24:35.57: [ 440]: MODEM Command error
May 05 00:24:35.57: [ 440]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
May 05 00:24:35.81: [ 440]: --> [2:OK]
May 05 00:24:35.81: [ 440]: <-- [22:AT+FLI="NothingSetup"\r]
May 05 00:24:36.05: [ 440]: --> [2:OK]
May 05 00:24:36.05: [ 440]: DIAL 2523608
May 05 00:24:36.05: [ 440]: <-- [13:ATDT2523608@\r]
May 05 00:24:52.70: [ 440]: --> [4:+FCO]
May 05 00:24:55.30: [ 440]: --> [12:+FNF:\xad6@\x80(^A\xf0]
May 05 00:24:55.30: [ 440]: REMOTE NSF "\xad6@\x80(^A\xf0"
May 05 00:24:55.30: [ 440]: --> [27:+FCI:" 416 252 3608"]
May 05 00:24:55.30: [ 440]: REMOTE CSI "416 252 3608"
May 05 00:24:55.30: [ 440]: --> [20:+FIS:1,3,0,2,1,0,1,4]
May 05 00:24:55.30: [ 440]: --> [2:OK]
May 05 00:24:55.30: [ 440]: REMOTE best rate 9600 bit/s
May 05 00:24:55.30: [ 440]: REMOTE max page width 1728 pixels in 215 mm
May 05 00:24:55.30: [ 440]: REMOTE max unlimited page length
May 05 00:24:55.30: [ 440]: REMOTE best vres 7.7 line/mm
May 05 00:24:55.30: [ 440]: REMOTE best format 2-D MR
May 05 00:24:55.30: [ 440]: REMOTE best 20 ms, 10 ms/scanline
May 05 00:24:55.30: [ 440]: USE 9600 bit/s
May 05 00:24:55.30: [ 440]: USE 20 ms, 10 ms/scanline
May 05 00:24:55.30: [ 440]: SEND file "docq/doc20.cover;30"
May 05 00:24:55.31: [ 440]: USE page width 1728 pixels in 215 mm
May 05 00:24:55.31: [ 440]: USE unlimited page length
May 05 00:24:55.31: [ 440]: USE 3.85 line/mm
May 05 00:24:55.31: [ 440]: USE 1-D MR
May 05 00:24:55.31: [ 440]: <-- [23:AT+FIS=0,3,0,2,0,0,0,4\r]
May 05 00:24:55.56: [ 440]: --> [2:OK]
May 05 00:24:55.56: [ 440]: <-- [7:AT+FDT\r]
May 05 00:24:55.84: [ 440]: --> [20:+FCS:0,3,0,2,0,0,0,4]
May 05 00:25:01.53: [ 440]: --> [7:CONNECT]
May 05 00:25:01.53: [ 440]: SEND begin page
May 05 00:25:01.53: [ 440]: <-- data [1031]
May 05 00:25:01.53: [ 440]: <-- data [1031]
May 05 00:25:01.53: [ 440]: <-- data [1029]
May 05 00:25:02.56: [ 440]: <-- data [1043]
May 05 00:25:02.56: [ 440]: <-- data [1026]
May 05 00:25:03.76: [ 440]: <-- data [1040]
May 05 00:25:03.76: [ 440]: <-- data [1044]
May 05 00:25:07.94: [ 440]: <-- data [1052]
May 05 00:25:07.94: [ 440]: <-- data [1058]
May 05 00:25:11.96: [ 440]: <-- data [1043]
May 05 00:25:11.96: [ 440]: <-- data [1051]
May 05 00:25:11.96: [ 440]: <-- data [1030]
May 05 00:25:14.76: [ 440]: <-- data [945]
May 05 00:25:14.76: [ 440]: SENT 13233 bytes of data
May 05 00:25:14.76: [ 440]: SEND 1D RTC
May 05 00:25:14.76: [ 440]: <-- data [9]
May 05 00:25:14.76: [ 440]: SEND end page
May 05 00:25:14.76: [ 440]: SEND send MPS (more pages, same document)
May 05 00:25:14.76: [ 440]: <-- data [2]
May 05 00:25:33.09: [ 440]: --> [7:+FHS:51]
May 05 00:25:33.09: [ 440]: REMOTE HANGUP: RSPREC error/got DCN (code
51)
May 05 00:25:33.09: [ 440]: <-- [5:ATH0\r]
May 05 00:25:33.21: [ 440]: --> [2:OK]
May 05 00:25:33.21: [ 440]: MODEM set DTR OFF
May 05 00:25:33.21: [ 440]: STATE CHANGE: SENDING -> MODEMWAIT (timeout
5)
May 05 00:25:33.21: [ 440]: SESSION END
