|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
"Unspecified Transmit Phase C error"
I'm on a Linux machine, kernel 2.2.13, and am running version
4.1beta2 of Hylafax, on an Intel 144/144e faxmodem with a Rockwell 144DP
chipset. ("Dec 21 16:44:12 cepheus FaxGetty[4098]: MODEM EXAR ROCKWELL
144DP/INTEL 14400E V1.7 MODEM CHIP : ROCKWELL RC144DP FAX CLASS 2")
When sending a fax, it gives me the following error...
Dec 21 13:55:44.03: [30416]: SESSION BEGIN 00000025 18183494367
Dec 21 13:55:44.03: [30416]: SEND FAX: JOB 7 DEST 3494367 COMMID 00000025
Dec 21 13:55:44.03: [30416]: DELAY 2600 ms
Dec 21 13:55:46.63: [30416]: <-- [15:ATE0V1Q0S0=0H0\r]
Dec 21 13:55:47.24: [30416]: --> [2:OK]
Dec 21 13:55:47.24: [30416]: <-- [30:ATS8=2S7=60&S1\G0\Q4\X1&D2&C1\r]
Dec 21 13:55:47.48: [30416]: --> [2:OK]
Dec 21 13:55:47.48: [30416]: <-- [12:AT+FCLASS=2\r]
Dec 21 13:55:47.71: [30416]: --> [2:OK]
Dec 21 13:55:47.71: [30416]: <-- [10:AT+FTBC=0\r]
Dec 21 13:55:47.94: [30416]: --> [5:ERROR]
Dec 21 13:55:47.94: [30416]: MODEM Command error
Dec 21 13:55:47.94: [30416]: <-- [10:AT+FBOR=0\r]
Dec 21 13:55:48.17: [30416]: --> [2:OK]
Dec 21 13:55:48.17: [30416]: <-- [13:AT+FPHCTO=30\r]
Dec 21 13:55:48.41: [30416]: --> [5:ERROR]
Dec 21 13:55:48.41: [30416]: MODEM Command error
Dec 21 13:55:48.41: [30416]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Dec 21 13:55:48.65: [30416]: --> [2:OK]
Dec 21 13:55:48.65: [30416]: <-- [7:ATL0M1\r]
Dec 21 13:55:48.88: [30416]: --> [2:OK]
Dec 21 13:55:48.88: [30416]: <-- [12:AT+FCLASS=2\r]
Dec 21 13:55:49.21: [30416]: --> [2:OK]
Dec 21 13:55:49.21: [30416]: <-- [10:AT+FTBC=0\r]
Dec 21 13:55:49.54: [30416]: --> [5:ERROR]
Dec 21 13:55:49.54: [30416]: MODEM Command error
Dec 21 13:55:49.54: [30416]: <-- [10:AT+FBOR=0\r]
Dec 21 13:55:49.87: [30416]: --> [2:OK]
Dec 21 13:55:49.87: [30416]: <-- [13:AT+FPHCTO=30\r]
Dec 21 13:55:50.21: [30416]: --> [5:ERROR]
Dec 21 13:55:50.21: [30416]: MODEM Command error
Dec 21 13:55:50.21: [30416]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Dec 21 13:55:50.55: [30416]: --> [2:OK]
Dec 21 13:55:50.55: [30416]: <-- [18:AT+FLID="RPM-PSI"\r]
Dec 21 13:55:50.89: [30416]: --> [2:OK]
Dec 21 13:55:50.89: [30416]: DIAL 3494367
Dec 21 13:55:50.89: [30416]: <-- [13:ATDT3494367@\r]
Dec 21 13:56:02.52: [30416]: --> [3:CED]
Dec 21 13:56:06.58: [30416]: --> [5:+FCON]
Dec 21 13:56:06.58: [30416]: --> [79:+FNSF: 00 00 69 0E CE B8 B0 E0 81 80 C0 80 D3 81 80 97 82 F0 76 78 30 32 37 B8 ]
Dec 21 13:56:06.58: [30416]: REMOTE NSF " 00 00 69 0E CE B8 B0 E0 81 80 C0 80 D3 81 80 97 82 F0 76 78 30 32 37 B8"
Dec 21 13:56:06.58: [30416]: --> [29:+FCSI: "ROT PRECISION MECH "]
Dec 21 13:56:06.58: [30416]: REMOTE CSI "ROT PRECISION MECH"
Dec 21 13:56:06.73: [30416]: --> [22:+FDIS: 1,3,0,2,0,2,0,4]
Dec 21 13:56:06.73: [30416]: --> [2:OK]
Dec 21 13:56:06.73: [30416]: REMOTE best rate 9600 bit/s
Dec 21 13:56:06.73: [30416]: REMOTE max page width 1728 pixels in 215 mm
Dec 21 13:56:06.73: [30416]: REMOTE max unlimited page length
Dec 21 13:56:06.73: [30416]: REMOTE best vres 7.7 line/mm
Dec 21 13:56:06.73: [30416]: REMOTE best format 1-D MR
Dec 21 13:56:06.73: [30416]: REMOTE supports T.30 Annex C, half duplex ECM
Dec 21 13:56:06.73: [30416]: REMOTE best 20 ms, 10 ms/scanline
Dec 21 13:56:06.73: [30416]: USE 9600 bit/s
Dec 21 13:56:06.73: [30416]: USE 20 ms, 10 ms/scanline
Dec 21 13:56:06.73: [30416]: SEND file "docq/doc7.ps;30"
Dec 21 13:56:06.73: [30416]: USE page width 1728 pixels in 215 mm
Dec 21 13:56:06.73: [30416]: USE unlimited page length
Dec 21 13:56:06.73: [30416]: USE 3.85 line/mm
Dec 21 13:56:06.73: [30416]: USE 1-D MR
Dec 21 13:56:06.73: [30416]: <-- [24:AT+FDIS=0,3,0,2,0,0,0,4\r]
Dec 21 13:56:08.11: [30416]: --> [9:+FHNG: 40]
Dec 21 13:56:08.11: [30416]: REMOTE HANGUP: Unspecified Transmit Phase C error (code 40)
Dec 21 13:56:08.11: [30416]: --> [2:OK]
Dec 21 13:56:08.11: [30416]: <-- [7:AT+FDT\r]
Dec 21 13:56:08.53: [30416]: --> [10:NO CARRIER]
Dec 21 13:56:08.53: [30416]: MODEM No carrier
Dec 21 13:56:08.53: [30416]: SEND: Unspecified Transmit Phase C error; Giving up after 3 attempts to send same page "docq/doc7.ps;30", dirnum 0
Dec 21 13:56:08.53: [30416]: <-- [5:ATH0\r]
Dec 21 13:56:09.23: [30416]: --> [2:OK]
Dec 21 13:56:09.23: [30416]: SESSION END
This is my current config setup:
ModemType: Class2 # use class 2 interface
ModemRate: 19200 # fax send&recv is locked at 19.2
ModemFlowControl: xonxoff # default
#
ModemSoftFlowCmd: AT&S1\G0\Q4\X1 # software flow control
ModemSetupDTRCmd: AT&D2 # DTR off causes modem to reset
ModemSetupDCDCmd: AT&C1 # DCD follows carrier
ModemSetupAACmd: AT+FAA=1 # enable in current class
#
ModemSendFillOrder: LSB2MSB # as expected
ModemRecvFillOrder: MSB2LSB # opposite of what makes sense
#
ModemDialCmd: ATDT%s@ # T for tone dialing, @ for
silence
#
ModemWaitForConnect: yes # wait for CONNECT on answer
#
Class2RecvDataTrigger: "\022" # DC2
Class2DDISCmd: "AT+FDIS" # set parameter before dialing
Suggestions..? Please email back to root@rpm-psi.com, as I am not
on this list. Thanks in advance.
