flexfax: polling: Remote is not T.4 compatible

["A. Satow" <mailing@toba.rhein-neckar.de>]

Hello,

I configured Hylafax as fax server

My problem is:  
when polling specific machines with an USR Modem, 
communication breaks down using Class 1. 
Polling with Class 2 leads to absolutely no results. 

The Log file says:  
Class1:       Remote is not T.4 compatible [log file attached]
Class 2.0:   Unspecified Phase C error, including too much delay    
                  between TCF and +FDR command (code 90) [log file    
                  not attached]
A few months ago, there was a similar question posted to the 
mailing list, I tried the solution provided there but it did not work. 
I also tested same modem with another machine running WinNT 
4.0 and Winfax 9.0 and the poll was succesful.

As I am clueless about how to proceed and what to try, I would 
appreciate any help!

Thanks very much in advance.

Bye,
Alex



Hylafax:  
hylafax-v4.0pl2

Modem configuration:
modem.config = usr-rts (Class 1, RTS/CTS, baud rate19200) file 
provided with Hylafax

OS:
FreeBSD 3.4-RC, gcc version 2.7.2.3 (and Linux 2.2.12)


Modem: 
external 3com/USRobotics Sportster Flash x2

ATI0 provides 
Product Code 5601


ATI7 provides: 
Configuration Profile...
Product type           Germany External
Product ID:              02566300
Options                   V32bis,V.34+,x2,V.90
Fax Options            Class 1/Class 2.0
Voice Options         Speakerphone, TAD
Clock Freq              92.0Mhz
EPROM                  256k
RAM                       32k
FLASH date           3/2/98
FLASH rev             11.1.17
DSP date                3/2/98
DSP rev                  11.1.17
Product type            Germany External
Product ID:               02566300

Log File:
[12911]: SESSION BEGIN 00000002 49190192247005
[12911]: SEND FAX: JOB 3 DEST 0190192247005 COMMID 
00000002
[12911]: MODEM set DTR OFF
[12911]: DELAY 2600 ms
[12911]: MODEM set DTR ON
[12911]: MODEM set baud rate: 19200 baud, input flow RTS/CTS, 
output flow RTS/CTS
[12911]: MODEM flush i/o
[12911]: <-- [17:ATE0V1Q0X4S0=0H0\r]
[12911]: --> [2:OK]
[12911]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=1&D2&C1\r]
[12911]: --> [2:OK]
[12911]: <-- [12:AT+FCLASS=1\r]
[12911]: --> [2:OK]
[12911]: <-- [12:AT&H1&I0&R2\r]
[12911]: --> [2:OK]
[12911]: <-- [21:AT+FCLASS=0&H1&I0&R2\r]
[12911]: --> [2:OK]
[12911]: <-- [5:ATM0\r]
[12911]: --> [2:OK]
[12911]: MODEM input buffering enabled
[12911]: <-- [12:AT+FCLASS=1\r]
[12911]: --> [2:OK]
[12911]: <-- [12:AT&H1&I0&R2\r]
[12911]: --> [2:OK]
[12911]: DIAL 0190192247005
[12911]: <-- [18:ATDT0190192247005\r]
[12911]: --> [7:CONNECT]
[12911]: MODEM input buffering disabled
[12911]: --> [2:OK]
[12911]: <-- [9:AT+FRH=3\r]
[12911]: --> [7:CONNECT]
[12911]: --> [2:OK]
[12911]: REMOTE CSI "15"
[12911]: <-- [9:AT+FRH=3\r]
[12911]: --> [7:CONNECT]
[12911]: --> [2:OK]
[12911]: Remote is not T.4 compatible
[12911]: SEND FAILED: Remote is not T.4 compatible
[12911]: <-- [9:AT+FTH=3\r]
[12911]: --> [7:CONNECT]
[12911]: <-- data [3]
[12911]: <-- data [2]
[12911]: --> [2:OK]
[12911]: MODEM input buffering enabled
[12911]: <-- [5:ATH0\r]
[12911]: --> [2:OK]
[12911]: MODEM set DTR OFF
[12911]: SESSION END

--
A. Satow
e-mail: a.satow@toba.rhein-neckar.de