|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
USR prof msg + REMOTE HANGUP: RSPREC error/got DCN (code 51)
Hallo,
I=B4m using HylaFAX, Version 4.0 (release).
When I try to send a fax I receive the following error messages:
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
Your facsimile job to 0231513453 was not sent because:
> RSPREC error/got DCN
> The job will be retried at 16:02.
> ---- Transcript of session follows ----
> Jul 29 15:56:28.78: [ 302]: SESSION BEGIN 00000003 49231513453
> Jul 29 15:56:28.79: [ 302]: SEND FAX: JOB 2 DEST 0231513453
COMMID=20
00000003
> Jul 29 15:56:28.79: [ 302]: MODEM set DTR OFF
> Jul 29 15:56:28.79: [ 302]: DELAY 2600 ms
> Jul 29 15:56:31.38: [ 302]: MODEM set DTR ON
> Jul 29 15:56:31.38: [ 302]: MODEM set baud rate: 38400 baud,
input=20
flow RTS/CTS, output flow RTS/CTS
> Jul 29 15:56:31.38: [ 302]: MODEM flush i/o
> Jul 29 15:56:31.38: [ 302]: <-- [17:ATE0V1Q0X4S0=3D0H0\r]
> Jul 29 15:56:31.52: [ 302]: --> [2:OK]
> Jul 29 15:56:31.52: [ 302]: <--
[27:ATS8=3D2S7=3D60&H1&I0&R2&D2&C1\r]
> Jul 29 15:56:31.65: [ 302]: --> [2:OK]
> Jul 29 15:56:31.65: [ 302]: <-- [14:AT+FCLASS=3D2.0\r]
> Jul 29 15:56:31.78: [ 302]: --> [2:OK]
> Jul 29 15:56:31.78: [ 302]: <-- [9:AT+FLO=3D2\r]
> Jul 29 15:56:31.91: [ 302]: --> [2:OK]
> Jul 29 15:56:31.91: [ 302]: <-- [9:AT+FPP=3D0\r]
> Jul 29 15:56:32.04: [ 302]: --> [2:OK]
> Jul 29 15:56:32.04: [ 302]: <-- [9:AT+FBO=3D0\r]
> Jul 29 15:56:32.17: [ 302]: --> [2:OK]
> Jul 29 15:56:32.17: [ 302]: <-- [10:AT+FCT=3D30\r]
> Jul 29 15:56:32.30: [ 302]: --> [2:OK]
> Jul 29 15:56:32.30: [ 302]: <-- [15:AT+FNR=3D1,1,1,1\r]
> Jul 29 15:56:32.43: [ 302]: --> [2:OK]
> Jul 29 15:56:32.43: [ 302]: <-- [9:AT+FIE=3D0\r]
> Jul 29 15:56:32.56: [ 302]: --> [2:OK]
> Jul 29 15:56:32.56: [ 302]: <-- [23:AT+FCC=3D1,5,2,2,0,0,0,0\r]
> Jul 29 15:56:32.69: [ 302]: --> [2:OK]
> Jul 29 15:56:32.69: [ 302]: <-- [5:ATM0\r]
> Jul 29 15:56:32.82: [ 302]: --> [2:OK]
> Jul 29 15:56:32.82: [ 302]: MODEM input buffering enabled
> Jul 29 15:56:32.82: [ 302]: <-- [14:AT+FCLASS=3D2.0\r]
> Jul 29 15:56:33.05: [ 302]: --> [2:OK]
> Jul 29 15:56:33.05: [ 302]: <-- [9:AT+FLO=3D2\r]
> Jul 29 15:56:33.28: [ 302]: --> [2:OK]
> Jul 29 15:56:33.28: [ 302]: <-- [9:AT+FPP=3D0\r]
> Jul 29 15:56:33.51: [ 302]: --> [2:OK]
> Jul 29 15:56:33.51: [ 302]: <-- [9:AT+FBO=3D0\r]
> Jul 29 15:56:33.74: [ 302]: --> [2:OK]
> Jul 29 15:56:33.74: [ 302]: <-- [10:AT+FCT=3D30\r]
> Jul 29 15:56:33.97: [ 302]: --> [2:OK]
> Jul 29 15:56:33.97: [ 302]: <-- [15:AT+FNR=3D1,1,1,1\r]
> Jul 29 15:56:34.20: [ 302]: --> [2:OK]
> Jul 29 15:56:34.20: [ 302]: <-- [9:AT+FIE=3D0\r]
> Jul 29 15:56:34.43: [ 302]: --> [2:OK]
> Jul 29 15:56:34.43: [ 302]: <-- [23:AT+FCC=3D1,5,2,2,0,0,0,0\r]
> Jul 29 15:56:34.66: [ 302]: --> [2:OK]
> Jul 29 15:56:34.66: [ 302]: <-- [30:AT+FLI=3D"Katharina Cordes &
M"\r]
> Jul 29 15:56:34.90: [ 302]: --> [2:OK]
> Jul 29 15:56:34.92: [ 302]: DIAL 0231513453
> Jul 29 15:56:34.92: [ 302]: <-- [15:ATDT0231513453\r]
> Jul 29 15:57:06.84: [ 302]: --> [4:+FCO]
> Jul 29 15:57:09.54: [ 302]: --> [10:+FNF:P?:=02 ]
> Jul 29 15:57:09.54: [ 302]: REMOTE NSF "P?:=02"
> Jul 29 15:57:09.54: [ 302]: --> [27:+FCI:"
513453"]
> Jul 29 15:57:09.54: [ 302]: REMOTE CSI "513453"
> Jul 29 15:57:09.54: [ 302]: --> [20:+FIS:1,3,0,2,1,0,0,4]
> Jul 29 15:57:09.54: [ 302]: --> [2:OK]
> Jul 29 15:57:09.54: [ 302]: REMOTE best rate 9600 bit/s
> Jul 29 15:57:09.54: [ 302]: REMOTE max page width 1728 pixels
in 215=20
mm
> Jul 29 15:57:09.54: [ 302]: REMOTE max unlimited page length
> Jul 29 15:57:09.54: [ 302]: REMOTE best vres 7.7 line/mm
> Jul 29 15:57:09.54: [ 302]: REMOTE best format 2-D MR
> Jul 29 15:57:09.54: [ 302]: REMOTE best 20 ms, 10 ms/scanline
> Jul 29 15:57:09.54: [ 302]: USE 9600 bit/s
> Jul 29 15:57:09.54: [ 302]: USE 20 ms, 10 ms/scanline
> Jul 29 15:57:09.54: [ 302]: SEND file "docq/doc3.ps;00"
> Jul 29 15:57:09.54: [ 302]: USE page width 1728 pixels in 215
mm
> Jul 29 15:57:09.54: [ 302]: USE unlimited page length
> Jul 29 15:57:09.54: [ 302]: USE 3.85 line/mm
> Jul 29 15:57:09.54: [ 302]: USE 1-D MR
> Jul 29 15:57:09.54: [ 302]: <-- [23:AT+FIS=3D0,3,0,2,0,0,0,4\r]
> Jul 29 15:57:09.78: [ 302]: --> [2:OK]
> Jul 29 15:57:09.78: [ 302]: <-- [7:AT+FDT\r]
> Jul 29 15:57:10.05: [ 302]: --> [20:+FCS:0,3,0,2,0,0,0,4]
> Jul 29 15:57:15.63: [ 302]: --> [7:CONNECT]
> Jul 29 15:57:15.63: [ 302]: SEND begin page
> Jul 29 15:57:35.65: [ 302]: SENT 22955 bytes of data
> Jul 29 15:57:35.65: [ 302]: SEND 1D RTC
> Jul 29 15:57:35.65: [ 302]: SEND end page
> Jul 29 15:57:35.65: [ 302]: SEND send EOP (no more pages or documents)
> Jul 29 15:57:49.00: [ 302]: --> [7:+FHS:51]
> Jul 29 15:57:49.00: [ 302]: REMOTE HANGUP: RSPREC error/got DCN (code =
51)
> Jul 29 15:57:49.00: [ 302]: <-- [5:ATH0\r]
> Jul 29 15:57:49.12: [ 302]: --> [2:OK]
> Jul 29 15:57:49.12: [ 302]: MODEM set DTR OFF
> Jul 29 15:57:49.12: [ 302]: SESSION END
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
My config.modem actually looks like this:
[...]
RingsBeforeAnswer: 5
[...]
ModemType: Class2.0 # use this to supply a hint
ModemRate: 38400 # max rate for DCE-DTE communication
ModemFlowControl: rtscts # XON/XOFF flow control assumed
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
ModemDialCmd: ATDT%s # T for tone dialing, @ for silence
ModemResetCmds: "" # stuff to do when modem is reset
ModemAnswerCmd: ATA # use this to answer phone
ModemNoFlowCmd: AT&HO&I0&R1 # disable flow control cmd
ModemHardFlowCmd: AT&H1&I0&R2 # hardware flow control cmd
ModemSoftFlowCmd: AT&H2&I2&R1 # software flow control cmd
ModemNoAutoAnswerCmd: ATS0=3D0 # disable auto-answer
ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd: ATE0 # disable command echo
ModemVerboseResultsCmd: ATV1 # enable verbose command results
ModemResultCodesCmd: ATQ0X4 # enable result codes
ModemOnHookCmd: ATH0 # place phone on hook (hangup)
ModemSoftResetCmd: ATZ # do soft reset of modem
ModemWaitTimeCmd: ATS7=3D60 # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=3D2 # comma pause time is 2 seconds
ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
Class2Cmd: AT+FCLASS=3D2.0 # command to enter class 2.0
Class2BORCmd: AT+FBO=3D0 # bit order for phase B/C/D (direct)
Class2CQCmd: "" # commands to enable copy quality proc.
Class2AbortCmd: AT+FKS # abort session command
Class2CQQueryCmd: AT+FCQ=3D? # query for copy quality capabilities
Class2DCCQueryCmd: AT+FCC=3D? # query for modem capabilities
Class2TBCCmd: AT+FPP=3D0 # setup stream mode
Class2CRCmd: AT+FCR=3D1 # enable capability to receive
Class2PHCTOCmd: AT+FCT=3D30 # set phase C timeout parameter
Class2BUGCmd: AT+FBU=3D1 # enable HDLC frame tracing
Class2LIDCmd: AT+FLI # set local identifier command
Class2DCCCmd: AT+FCC # set modem capabilities command
Class2DISCmd: AT+FIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command hack
Class2CIGCmd: AT+FPI # set polling identifier command
Class2NRCmd: AT+FNR=3D1,1,1,0 # setup status reporting command
Class2PIECmd: AT+FIE=3D0 # disable interrupt-enable command
Class2PTSCmd: AT+FPS # set post-page status command
Class2SPLCmd: AT+FSP # set polling indicator command
Class2NFLOCmd: AT+FLO=3D0 # set no flow control command
Class2SFLOCmd: AT+FLO=3D1 # set software flow control command
Class2HFLOCmd: AT+FLO=3D2 # set hardware flow control command
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
Any suggestions would be greatly appreciated !
Regards,
Michael
