flexfax: hylafax and mgetty

[Torsten Mueller <archesoft@pc.mdlink.de>]

hello,
my modem is a multitech 2834zdxg

my problem: sometimes if there is an incoming fax, faxgetty tries to
start
mgetty (why this ?) and mgetty tries to get the fax .
then i get a message from mgetty like this:

*From: Fax Getty <root@slave.city-computer.com>
*To: faxadm@slave.city-computer.com
*Subject: fax from _       +496003815222_
*
*A fax was successfully received:
*Sender ID: _       +496003815222_
*Pages received: 1
*Modem device: ttyS0
*Communication parameters: +FDCS:0,5,0,2,0,0,0,0
*   Resolution : normal
*    Bit Rate   : 14400
*   Page Width : 1728 pixels
*    Page Length: unlimited
*    Compression: 0 (1d mod Huffman)
*    Error Corr.: none
*    Scan Time  : 0
*Reception Time : 00:47
*Spooled G3 fax files:
* /tmp/FAXnd8f0.01
*regards, your modem subsystem.

1. Why tries mgetty to process the incoming call and not faxgetty ?
2. How can i "disable" mgetty, so that all incoming calls are handled by
faxgetty ?
3. What about this file /tmp/FAXnd8f0.01 ? it seems not to be a valid
bitmap, tiff, ps file.
4. Is it o.k. to use this config file, as it is for Multi-Tech MT1432,
MT224BA, and MT1932ZDX modems ?

Thanks for your help,

Torsten

--------------------------------------
my config ttyS0 for the multitech:

# Configuration for a Multi-Tech MT1432, MT224BA, and MT1932ZDX modems.
#
# MT1432 firmware rev 0307 I or newer
# MT132BG rev 0109A
# MT1932ZDX rev 0109H
#
# Note that MT1432 modems come in several varieties:
#
# MT1432BA uses Rockwell data pump
# MT1432BA/A uses AT&T data pump
# MT1432BG MT1432BA tweaked for German FCC
# MT1432MK (for UK?)
#
# The modem has been tried with both XON/XOFF and RTS/CTS flow
# control; this configuration is for hardware flow control.
#
#
CountryCode:  49
AreaCode:  391
FAXNumber:  +49.391.7319173
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules
ServerTracing:  527
SessionTracing:  527
RecvFileMode:  0666
LogFileMode:  0666
DeviceMode:  0600
RingsBeforeAnswer: 2
SpeakerVolume:  medium
GettyArgs:  "-h %l dx_%s"
LocalIdentifier: "__"
TagLineFont:  etc/lutRS18.pcf
TagLineFormat:  "From %%l|%c|Page %%p of %%t"
MaxRecvPages:  25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:  Class2  # use class 2 interface
ModemRate:  38400  # lock rate for DCE-DTE communication
ModemFlowControl: rtscts  # default
ModemHardFlowCmd: AT&E4  # hardware flow control
ModemSoftFlowCmd: AT&E5  # software flow control
ModemSetupDTRCmd: AT&D3  # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1  # setup so DCD reflects carrier (or not)
ModemSetupAACmd: AT+FAA=1 # enable adaptive-answer in class 2
ModemDialCmd:  ATX3DT%s  # T for tone dialing, @ for silence
#
Class2RecvDataTrigger: "\022"  # character sent to modem to start recv