flexfax: Problem with only one Destination

[Matthias Reich EDV-Programmierung <rei@hagos.de>]

Hallo again to everboy on this list.

Please send answers as cc: to rei@hagos.de
because I'm no subscriber.

Still running Hylafax V4.0pl1 on Solaris 2.5.1 with
3 Multitech MT1432 BG Rom-Rev. 1.11

I got one destination which is not
able to receive faxes from 
hylafax. sending the same by hand is ok.

Here is the session log:

--- cut here
Jul 05 11:26:50.12: [24438]: SESSION BEGIN 00063555 4983369707
Jul 05 11:26:50.12: [24438]: SEND FAX: JOB 27001 DEST 083369707 COMMID
00063555
Jul 05 11:26:50.12: [24438]: DELAY 2600 ms
Jul 05 11:26:52.97: [24438]: <-- [15:ATE0V1Q0S0=0H0\r]
Jul 05 11:26:53.19: [24438]: --> [2:OK]
Jul 05 11:26:53.19: [24438]: <-- [21:ATS8=2S7=60&E4&D3&C1\r]
Jul 05 11:26:53.41: [24438]: --> [2:OK]
Jul 05 11:26:53.41: [24438]: <-- [12:AT+FCLASS=2\r]
Jul 05 11:26:53.62: [24438]: --> [2:OK]
Jul 05 11:26:53.62: [24438]: <-- [10:AT+FTBC=0\r]
Jul 05 11:26:53.83: [24438]: --> [2:OK]
Jul 05 11:26:53.83: [24438]: <-- [10:AT+FBOR=0\r]
Jul 05 11:26:54.05: [24438]: --> [2:OK]
Jul 05 11:26:54.05: [24438]: <-- [13:AT+FPHCTO=30\r]
Jul 05 11:26:54.26: [24438]: --> [2:OK]
Jul 05 11:26:54.26: [24438]: <-- [24:AT+FDCC=1,3,2,2,0,0,0,0\r]
Jul 05 11:26:54.48: [24438]: --> [2:OK]
Jul 05 11:26:54.48: [24438]: <-- [7:ATL0M1\r]
Jul 05 11:26:54.69: [24438]: --> [2:OK]
Jul 05 11:26:54.69: [24438]: <-- [12:AT+FCLASS=2\r]
Jul 05 11:26:55.00: [24438]: --> [2:OK]
Jul 05 11:26:55.00: [24438]: <-- [10:AT+FTBC=0\r]
Jul 05 11:26:55.31: [24438]: --> [2:OK]
Jul 05 11:26:55.31: [24438]: <-- [10:AT+FBOR=0\r]
Jul 05 11:26:55.62: [24438]: --> [2:OK]
Jul 05 11:26:55.62: [24438]: <-- [13:AT+FPHCTO=30\r]
Jul 05 11:26:55.93: [24438]: --> [2:OK]
Jul 05 11:26:55.93: [24438]: <-- [24:AT+FDCC=1,3,2,2,0,0,0,0\r]
Jul 05 11:26:56.24: [24438]: --> [2:OK]
Jul 05 11:26:56.24: [24438]: <-- [29:AT+FLID="HAGOS eG Stuttgart"\r]
Jul 05 11:26:56.56: [24438]: --> [2:OK]
Jul 05 11:26:56.56: [24438]: DIAL 083369707
Jul 05 11:26:56.56: [24438]: <-- [21:ATDT0,01030083369707\r]
Jul 05 11:27:21.95: [24438]: --> [5:+FCON]
Jul 05 11:27:24.11: [24438]: --> [27:+FNSF:BC 53 01 10 12 00 01 ]
Jul 05 11:27:24.11: [24438]: REMOTE NSF "BC 53 01 10 12 00 01"
Jul 05 11:27:24.11: [24438]: --> [28:+FCSI:"       +49 8336 9707"]
Jul 05 11:27:24.11: [24438]: REMOTE CSI "+49 8336 9707"
Jul 05 11:27:24.11: [24438]: --> [21:+FDIS:1,3,0,2,1,0,0,4]
Jul 05 11:27:24.11: [24438]: --> [2:OK]
Jul 05 11:27:24.11: [24438]: REMOTE best rate 9600 bit/s
Jul 05 11:27:24.12: [24438]: REMOTE max page width 1728 pixels in 215 mm
Jul 05 11:27:24.12: [24438]: REMOTE max unlimited page length
Jul 05 11:27:24.12: [24438]: REMOTE best vres 7.7 line/mm
Jul 05 11:27:24.12: [24438]: REMOTE best format 2-D MR
Jul 05 11:27:24.12: [24438]: REMOTE best 20 ms, 10 ms/scanline
Jul 05 11:27:24.12: [24438]: USE 9600 bit/s
Jul 05 11:27:24.12: [24438]: USE 20 ms, 10 ms/scanline
Jul 05 11:27:24.12: [24438]: SEND file "docq/doc27028.ps;00"
Jul 05 11:27:24.12: [24438]: USE page width 1728 pixels in 215 mm
Jul 05 11:27:24.12: [24438]: USE unlimited page length
Jul 05 11:27:24.12: [24438]: USE 3.85 line/mm
Jul 05 11:27:24.12: [24438]: USE 1-D MR
Jul 05 11:27:24.12: [24438]: <-- [24:AT+FDIS=0,3,0,2,0,0,0,4\r]
Jul 05 11:27:24.48: [24438]: --> [2:OK]
Jul 05 11:27:24.48: [24438]: <-- [7:AT+FDT\r]
Jul 05 11:27:48.27: [24438]: --> [8:+FHNG:25]
Jul 05 11:27:48.27: [24438]: REMOTE HANGUP: DCS sent 3 times without
response (code 25)
Jul 05 11:27:48.37: [24438]: --> [0:]
Jul 05 11:27:48.37: [24438]: MODEM <Empty line>
Jul 05 11:27:48.37: [24438]: <-- [5:ATH0\r]
Jul 05 11:27:48.37: [24438]: MODEM WRITE ERROR: errno 5
Jul 05 11:27:48.37: [24438]: SESSION END
--- cut here

does anybody have a suggestion what happens there ??

the remote destination is an Siemens 840 Fax-Machine.

thanx a lot

-- 
HAGOS eG                 phone: +49 711 7880592
Matthias Reich             fax: +49 711 7880599
Industriestr. 62           web: http://www.hagos.de
D-70565 Stuttgart         mail: rei@hagos.de
Germany