|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: FW: facsimile not received ????
On 01-Feb-99 Hong Kong Observatory wrote:
> Hi,
>
> I think you have to submit information on your modem model, operating
> system, modem config files.....
>
>
Modem Lasat unique 1280mi
at+fclass=?
z0,1,2,1.0,80
Linux on Intel Kernel 2.0.36
calvin$ cat config
LogFacility: local5
CountryCode: 49
AreaCode: 721
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules.europe
ServerTracing: 1
ModemClass: 2
cat config.ttyS0
# $Id: class2,v 1.23 1996/06/24 02:58:32 sam Rel $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
# Generic Class 2 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode: 49
AreaCode: 721
FAXNumber: +49 721 9891004
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules.europe
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "Ruediger Gubler"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%p of %%t"
MaxRecvPages: 9999
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2 # use this to supply a hint
ModemRate: 38400
ModemFlowControl: rtscts
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd: ATDT%s@ # T for tone dialing, @ for silence
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds: "" # stuff to do when modem is reset
ModemAnswerCmd: ATA # use this to answer phone
ModemNoFlowCmd: AT&K # disable flow control cmd
ModemHardFlowCmd: AT&K3 # hardware flow control cmd
ModemSoftFlowCmd: AT&K4 # software flow control cmd
ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd: ATE0 # disable command echo
ModemVerboseResultsCmd: ATV1 # enable verbose command results
ModemResultCodesCmd: ATQ0 # enable result codes
ModemOnHookCmd: ATH0 # place phone on hook (hangup)
ModemSoftResetCmd: ATZ&Z*=9891004%M1 # do soft reset of modem
ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
#
# Configuration parameters for Class 2 modems.
#
Class2Cmd: AT+FCLASS=2 # command to enter class 2
Class2BORCmd: AT+FBOR=0 # bit order for phase B/C/D (direct)
Class2RELCmd: AT+FREL=1 # byte-align EOL codes on recv
Class2CQCmd: "" # commands to enable copy quality proc.
Class2AbortCmd: AT+FK # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities
Class2DCCQueryCmd: AT+FDCC=? # query for modem capabilities
Class2TBCCmd: AT+FTBC=0 # setup stream mode
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FPHCTO=30 # set phase C timeout parameter
Class2BUGCmd: AT+FBUG=1 # enable HDLC frame tracing
Class2LIDCmd: AT+FLID # set local identifier command
Class2DCCCmd: AT+FDCC # set modem capabilities command
Class2DISCmd: AT+FDIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command hack
Class2CIGCmd: AT+FCIG # set polling identifier command
Class2PTSCmd: AT+FPTS # set post-page status command
Class2SPLCmd: AT+FSPL # set polling indicator command
#
# If Class2RecvDataTrigger is not set, then it is set to DC1
#
Class2RecvDataTrigger: "" # character sent to modem to start recv
Class2XmitWaitForXON: yes # if true, wait for XON before send
> On Fri, 29 Jan 1999, Ruediger Gubler wrote:
>
>>
>> Why???
>>
>> Jan 29 10:25:30.56: [ 6470]: --> [22:+FDCS: 0,5,0,2,0,0,0,0]
>> Jan 29 10:25:30.56: [ 6470]: REMOTE wants 14400 bit/s
>> Jan 29 10:25:30.56: [ 6470]: REMOTE wants page width 1728 pixels in 215 mm
>> Jan 29 10:25:30.56: [ 6470]: REMOTE wants unlimited page length
>> Jan 29 10:25:30.56: [ 6470]: REMOTE wants 3.85 line/mm
>> Jan 29 10:25:30.56: [ 6470]: REMOTE wants 1-D MR
>> Jan 29 10:25:30.56: [ 6470]: --> [2:OK]
>> Jan 29 10:25:30.56: [ 6470]: <-- [7:AT+FDR\r]
>> Jan 29 10:25:33.84: [ 6470]: --> [5:+FCFR]
>> Jan 29 10:25:37.39: [ 6470]: --> [22:+FDCS: 0,5,0,2,0,0,0,0]
>> Jan 29 10:25:37.39: [ 6470]: REMOTE wants 14400 bit/s
>> Jan 29 10:25:37.39: [ 6470]: REMOTE wants page width 1728 pixels in 215 mm
>> Jan 29 10:25:37.39: [ 6470]: REMOTE wants unlimited page length
>> Jan 29 10:25:37.39: [ 6470]: REMOTE wants 3.85 line/mm
>> Jan 29 10:25:37.39: [ 6470]: REMOTE wants 1-D MR
>> Jan 29 10:25:37.39: [ 6470]: --> [7:CONNECT]
>> Jan 29 10:25:37.39: [ 6470]: RECV: begin page
>> Jan 29 10:25:37.39: [ 6470]: RECV: send trigger 021
>> Jan 29 10:25:45.91: [ 6470]: RECV: 608 total lines, 606 bad lines, 567
>> consecutive bad lines
>> Jan 29 10:25:45.91: [ 6470]: --> [17:+FPTS: 1,2219,0,0]
>> Jan 29 10:25:48.07: [ 6470]: --> [7:+FET: 2]
>> Jan 29 10:25:48.07: [ 6470]: RECV recv EOP (no more pages or documents)
>> Jan 29 10:25:48.07: [ 6470]: --> [2:OK]
>> Jan 29 10:25:48.07: [ 6470]: RECV: REJECT page quality, 0% good lines (95%
>> required)
>> Jan 29 10:25:48.07: [ 6470]: RECV send RTN (retrain negative)
>> Jan 29 10:25:48.07: [ 6470]: <-- [10:AT+FPTS=2\r]
>> Jan 29 10:25:48.24: [ 6470]: --> [2:OK]
>> Jan 29 10:25:48.24: [ 6470]: <-- [7:AT+FDR\r]
>> Jan 29 10:25:52.35: [ 6470]: --> [8:+FHNG: 0]
>> Jan 29 10:25:52.35: [ 6470]: REMOTE HANGUP: Normal and proper end of
>> connection
>> (code 0)
>> Jan 29 10:25:52.35: [ 6470]: RECV FAX (00000008): recvq/fax00003.tif from
>> +49
>> 7243 541750, route to <unspecified>, 0 pages in 0
>> :24
>> Jan 29 10:25:52.35: [ 6470]: RECV FAX: Normal and proper end of connection
>> Jan 29 10:25:52.35: [ 6470]: RECV FAX (00000008): session with +49 7243
>> 541750
>> terminated abnormally: Normal and proper end of
>> connection
>> Jan 29 10:25:52.35: [ 6470]: RECV FAX: bin/faxrcvd "recvq/fax00003.tif"
>> "ttyS0"
>> "00000008" "Normal and proper end of connection
>> "
>>
>> --------------End of forwarded message-------------------------
>>
>> ---
>>
>> E-Mail: Ruediger Gubler <ruediger.gubler@plannet.de>
>> Date: 29-Jan-99
>> Time: 10:30:32
>>
>> Old musicians never die, they just decompose.
>>
>>
>
> K.S.Wat SSA(D)12
> Computer Division,
> Hong Kong Observatory.
---
E-Mail: Ruediger Gubler <ruediger.gubler@plannet.de>
Date: 01-Feb-99
Time: 12:21:39
My cup hath runneth'd over with love.
