Re: flexfax: Questions or Error Code

[Jacky Hui Chun Kit <ckhui@school.net.hk>]

Dear All,

    I would like to give some more info on my problem,

THe ROM version of my modemis as follow
----------------
ATI3I6
V2.083H2-K56_DLS

RC56DPF L8570A Rev 47.22/47.22
----------------

Here is my config.cua0
----------------
CountryCode:  852
#AreaCode:  415
FAXNumber:  29943269
LongDistancePrefix: 001
InternationalPrefix: 001
DialStringRules: etc/dialrules
ServerTracing:  1
SessionTracing:  11
RecvFileMode:  0600
LogFileMode:  0600
DeviceMode:  0600
RingsBeforeAnswer: 2
SpeakerVolume:  off
GettyArgs:  "-h %l %s"
LocalIdentifier: CyberCampus-Fax
TagLineFont:  etc/lutRS18.pcf
TagLineFormat:  "From %%l|%c|Page %%p of %%t"
MaxRecvPages:  25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:  Class1  # use this to supply a hint
#ModemRate:  19200  # rate for DCE-DTE communication
#ModemFlowControl: xonxoff  # XON/XOFF flow control assumed
#
#ModemSetupDTRCmd: AT&D2  # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1  # setup so DCD follows carrier
#GettyArgs:  "-h %l %s" # modem must auto-detect fax/data
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd:  ATDT%s@  # T for tone dialing, @ for silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds:  ""  # stuff to do when modem is reset
#ModemAnswerCmd:  ATA  # use this to answer phone
#ModemNoFlowCmd:  AT&K  # disable flow control cmd
#ModemHardFlowCmd: AT&K3  # hardware flow control cmd
#ModemSoftFlowCmd: AT&K4  # software flow control cmd
#ModemNoAutoAnswerCmd: ATS0=0  # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd: ATE0  # disable command echo
#ModemVerboseResultsCmd: ATV1  # enable verbose command results
#ModemResultCodesCmd: ATQ0  # enable result codes
#ModemOnHookCmd:  ATH0  # place phone on hook (hangup)
#ModemSoftResetCmd: ATZ  # do soft reset of modem
#ModemWaitTimeCmd: ATS7=60  # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd: ATS8=2  # comma pause time is 2 seconds
#ModemRecvFillOrder: LSB2MSB  # bit order of received facsimile
#ModemSendFillOrder: LSB2MSB  # bit order modem expects for transmit
#
Class1Cmd:  AT+FCLASS=1 # command to enter class 1
Class1TCFResponseDelay: 75  # 75ms delay between recv TCF & response
Class1SendPPMDelay: 75  # 75ms delay before sending PPM
Class1SendTCFDelay: 75  # 75ms delay between sending DCS & TCF
Class1TrainingRecovery: 1500  # 1.5sec delay after training failure
Class1RecvAbortOK: 200  # wait 200ms for abort response
Class1FrameOverhead: 4  # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer: 40000  # 35+5secs waiting for ident frames
Class1TCFMaxNonZero: 10  # max 10% of data may be non-zero
Class1TCFMinRun: 1000  # min run is 2/3rds of TCF duration
-----------------


I am running on Redhat5.1 with kernel 2.0.36 ,hylafaxv4.0pl2


THanks all.


Jacky hUi


David Woolley wrote:

> > Dear Sir,
>
> To avoid confusion, this is a mutual support group, not a support company.
>
> >     I ahve encounter a error "No Response to MPS or EOP" when I send a
> > two files fax using "sendfax -n -d telno. file1.ps file2.ps" , I want to
> > know what should I do? Anyone encounter this and what does it mean?
>
> The modem did not respond when Hylafax signalled end of page.  In default
> of adequate information, check your flow control, but really we
> need modem, operating system and Hylafax versions, any manual configuration
> changes and a detailed session log.