flexfax: Maximum ModemRate?

[John Conover <conover@inow.com>]

I have a USR 33.6 Faxmodem Sportster running in Class 1, with faxgetty(1)
for fax I/O, PPP I/O, and UUCP I/O. Changing config.cua1 from:

    ModemRate:              38400

to:
    
    ModemRate:              57600

makes the modem go away-it can't initialize, (can't deduce modem type.)

Is it possible to use this at 57600, or is this some kind of a violation?

	Thanks,

	John

BTW, the system is Linux, hardware flow control, config.cua1 is attached.
The system works reasonably well at 38400.

-- 

John Conover, 631 Lamont Ct., Campbell, CA., 95008, USA.
VOX 408.370.2688, FAX 408.379.9602
conover@inow.com, http://www2.inow.com/~conover/john.html

# $Id: usr-rts,v 1.6 1996/06/24 02:58:43 sam Rel $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
# Configuration for using the Class 1 command interface with
# a USR Courier or Sportster modem and RTS/CTS flow control.
#
CountryCode:		1
AreaCode:		408
FAXNumber:		+1.408.379.9602
LongDistancePrefix:	1
InternationalPrefix:	011
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0666
LogFileMode:		0666
DeviceMode:		0666
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"-h %l F38400 vt100"
LocalIdentifier:	+14083799602
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%p of %%t"
PercentGoodLines:	50
MaxConsecutiveBadLines:	100
MaxRecvPages:		100
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		# use class 1 interface
ModemRate:		38400		# max rate for DCE-DTE communication
ModemFlowControl:	rtscts		# hardware flow control
#
ModemSetupDTRCmd:	ATS13=1&D2	# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
ModemNoFlowCmd:		AT&H0&I0&R1	# setup modem for no flow control
ModemHardFlowCmd:	AT&H1&I0&R2	# setup modem for hardware flow control
ModemSoftFlowCmd:	AT&H2&I2&R1	# setup modem for software flow control
ModemResultCodesCmd:	ATQ0X4		# enable result codes
#
ModemMfrQueryCmd:	!USR
ModemModelQueryCmd:	ATI3
ModemRevQueryCmd:	ATI7		# XXX, returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd:		AT&H0&I0&R1	# setup modem for no flow control
Class1HFLOCmd:		AT&H1&I0&R2	# setup modem for hardware flow control
Class1SFLOCmd:		""		# modem does this automatically
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 1 while not sending or receiving facsimile.
#
ModemSetupAACmd:	AT+FAA=1+FCLASS=1&H1&I0&R2&A0&S1	# leave modem in class 1
ModemAnswerCmd:		AT+FAA=1+FCLASS=1&H1&I0&R2&A0&S1A	# force RTS/CTS after change to fax mode
ModemAnswerDataCmd:	AT&F1S2=255S7=90S13=1S19=90&A0&D2&S1E1M0A	# force reset after change to data mode
ModemWaitForConnect:	yes	# wait for CONNECT on answer