Hylafax Mailing List Archives

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

Problems With 4.0p2 and ROCKWELL RC32ACL/V1.410-AS29 (Class 2) [LINUX]



Hi!

i got a really annoying problem with my setup.
I can send faxes without a problem, but 
I cannot receive :(

here's a session tracing log:

====
sep 09 21:12:54.16: [  397]: SESSION BEGIN 00000010 33478265578
sep 09 21:12:54.16: [  397]: <-- [4:ATA\r]
sep 09 21:13:05.77: [  397]: --> [3:FAX]
sep 09 21:13:11.58: [  397]: --> [5:+FCON]
sep 09 21:13:11.58: [  397]: ANSWER: FAX CONNECTION
sep 09 21:13:11.58: [  397]: RECV FAX: begin
sep 09 21:16:11.62: [  397]: REMOTE HANGUP: Unspecified Receive Phase B error (code 70)
sep 09 21:16:11.64: [  397]: RECV FAX: Unspecified Receive Phase B error
sep 09 21:16:11.70: [  397]: RECV FAX: end
sep 09 21:16:11.70: [  397]: SESSION END
====

and this happens, no matter what the sending device is.
here's my etc/config.cua1

====
#
# Configuration for a Rockwell RC32ACL-based Class 2 modem.
#    Boca M1440E                firmware V1.000
#    SupraFAX v.32bis           firmware V1.000
# (and others)
#
# This configuration file sets up the modem to run at 38.4 for
# sending and for receiving.  RTS/CTS is used for flow control
# which also works for data connections.  Adaptive answer support
# is reliable, but to use it you must also enable ModemWaitForConnect
# to force the server to skip intermediate status messages and
# wait for the "CONNECT" message.
#
#

CountryCode:            33
AreaCode:               4
FAXNumber:              +33-478265578
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        "etc/dialrules"
ServerTracing:          1
SessionTracing:         1087
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0666
RingsBeforeAnswer:      1
SpeakerVolume:          low
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "Linux_54"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%p of %%t"
Use2D:                  yes

#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2          # use class 2 interface
ModemRate:              38400
ModemFlowControl:       rtscts          # default
ModemWaitForConnect:    yes             # wait for CONNECT on answer
#
#ModemResetCmds:        AT&F2           # what you want for a Supra
ModemNoFlowCmd:         AT&K            # disable flow control cmd
ModemHardFlowCmd:       AT&K3           # hardware flow control cmd
ModemSoftFlowCmd:       AT&K4           # software flow control cmd
ModemSetupDTRCmd:       AT&D2           # DTR off causes modem to reset
ModemSetupDCDCmd:       AT&C1           # DCD follows carrier
ModemSetupAACmd:        AT+FCLASS=0;+FAA=1 # enable in class 0
#
ModemSendFillOrder:     LSB2MSB         # as expected
ModemRecvFillOrder:     MSB2LSB         # opposite of what makes sense
Class2RecvDataTrigger:  "\022"          # a la 2388-B



Home
Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services