AW: flexfax: USR Sportster users..

[Christoph Stotz <pif@logo.de>]

Hello,

I was using some USR 33.6 but then changed to Elsa 33.6 because of too
many
Problems (check modem power, the modem is "hanging", problems faxing
etc.).

By the way: the Elsa seems to complete jobs slighly faster (less time is
needed for initialization etc.)

My last working configuration was:
<---cut---><---cut---><---cut---><---cut---><---cut---><---cut--->
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:      "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd:        ATE0            # disable command echo
ModemVerboseResultsCmd: ATV1            # enable verbose command results
ModemResultCodesCmd:    ATQ0            # enable result codes
ModemOnHookCmd:         ATH             # place phone on hook (hangup)
ModemSoftResetCmd:      ATZ             # do soft reset of modem
ModemWaitTimeCmd:       ATS7=60         # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2          # comma pause time is 2 seconds
ModemRecvFillOrder:     LSB2MSB         # bit order of received
facsimile
ModemSendFillOrder:     LSB2MSB         # bit order modem expects for
transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd:              AT+FCLASS=2.0   # command to enter class 2.0
Class2BORCmd:           AT+FBO=0        # bit order for phase B/C/D
(direct)
Class2CQCmd:            ""              # commands to enable copy
quality proc.
Class2AbortCmd:         AT+FKS          # abort session command
Class2CQQueryCmd:       AT+FCQ=?        # query for copy quality
capabilities
Class2DCCQueryCmd:      AT+FCC=?        # query for modem capabilities
Class2TBCCmd:           AT+FPP=0        # setup stream mode
Class2CRCmd:            AT+FCR=1        # enable capability to receive
Class2PHCTOCmd:         AT+FCT=30       # set phase C timeout parameter
Class2BUGCmd:           AT+FBU=1        # enable HDLC frame tracing
Class2LIDCmd:           AT+FLI          # set local identifier command
Class2DCCCmd:           AT+FCC          # set modem capabilities command
Class2DISCmd:           AT+FIS          # set session parameters command
Class2DDISCmd:          ""              # disable pre-dial DIS command
hack
Class2CIGCmd:           AT+FPI          # set polling identifier command
Class2NRCmd:            AT+FNR=1,1,1,1  # setup status reporting command
Class2PIECmd:           AT+FIE=0        # disable interrupt-enable
command
Class2PTSCmd:           AT+FPS          # set post-page status command
Class2SPLCmd:           AT+FSP          # set polling indicator command
Class2NFLOCmd:          AT+FLO=0        # set no flow control command
Class2SFLOCmd:          AT+FLO=1        # set software flow control
command
Class2HFLOCmd:          AT+FLO=2        # set hardware flow control
command
<---cut---><---cut---><---cut---><---cut---><---cut---><---cut--->

-----Ursprüngliche Nachricht-----
Von: Ludovic Marcotte [mailto:ludovic@Sophos.ca]
Gesendet am: Mittwoch, 29. Juli 1998 22:51
An: flexfax@sgi.com
Betreff: flexfax: USR Sportster users..

Hi all,
	I've sent a message or two on this list before asking help for a
problem I have with my USR Sportster 33.6 modem. Thanks for all the
reply
I had.

My question is..  is anybody actually using this modem and if yes, does
it
work properly for you? Everything is fine? If yes, I'm curious to see
your
config.ttyXX and I'll be glad to have it :-)

Thanks,
		Ludovic