Re: flexfax: No Pages sent

[Wolfgang Mettbach <wmettbach@metronet.de>]

          Hello Jonathan,

sorry, I posted the wrong session log. That one was created while trying
to use the modem as a class 2 fax modem. This one is the right one:

-------------------------------------------------------------------
May 08 09:41:35.22: [  359]: SESSION BEGIN 00000005 49523138089
May 08 09:41:35.25: [  359]: SEND FAX: JOB 7 DEST 0523138089 COMMID 00000005
May 08 09:41:35.25: [  359]: DELAY 2600 ms
May 08 09:41:37.88: [  359]: <-- [15:ATE0V1Q0S0=0H0\r]
May 08 09:41:38.65: [  359]: --> [2:OK]
May 08 09:41:38.65: [  359]: <-- [21:ATS8=2S7=60&K4&D2&C1\r]
May 08 09:41:38.68: [  359]: --> [2:OK]
May 08 09:41:38.68: [  359]: <-- [12:AT+FCLASS=1\r]
May 08 09:41:38.71: [  359]: --> [2:OK]
May 08 09:41:38.72: [  359]: <-- [12:AT+FCLASS=1\r]
May 08 09:41:38.85: [  359]: --> [2:OK]
May 08 09:41:39.16: [  359]: DIAL 0523138089
May 08 09:41:39.16: [  359]: <-- [16:ATDT0523138089@\r]
May 08 09:42:06.98: [  359]: --> [7:CONNECT]
May 08 09:42:08.72: [  359]: --> [2:OK]
May 08 09:42:08.72: [  359]: REMOTE CSI "+49 5231 38089"
May 08 09:42:08.72: [  359]: <-- [9:AT+FRH=3\r]
May 08 09:42:08.75: [  359]: --> [7:CONNECT]
May 08 09:42:08.77: [  359]: --> [2:OK]
May 08 09:42:08.77: [  359]: REMOTE best rate 9600 bit/s
May 08 09:42:08.77: [  359]: REMOTE max page width 1728 pixels in 215 mm
May 08 09:42:08.78: [  359]: REMOTE max unlimited page length 
May 08 09:42:08.78: [  359]: REMOTE best vres 7.7 line/mm
May 08 09:42:08.78: [  359]: REMOTE best format 2-D MR
May 08 09:42:08.78: [  359]: REMOTE best 20 ms, 10 ms/scanline
May 08 09:42:08.78: [  359]: USE 9600 bit/s
May 08 09:42:08.78: [  359]: USE 20 ms, 10 ms/scanline
May 08 09:42:08.79: [  359]: <-- [9:AT+FTH=3\r]
May 08 09:42:08.81: [  359]: --> [7:CONNECT]
May 08 09:42:08.81: [  359]: <-- data [3]
May 08 09:42:08.81: [  359]: <-- data [2]
May 08 09:42:10.03: [  359]: --> [2:OK]
May 08 09:42:10.03: [  359]: <-- [5:ATH0\r]
May 08 09:42:10.91: [  359]: --> [2:OK]
May 08 09:42:10.91: [  359]: SESSION END
-------------------------------------------------------------------

And this log was created while trying to receive a fax:

-------------------------------------------------------------------
May 08 09:29:26.36: [  281]: SESSION BEGIN 00000004 23303
May 08 09:29:26.39: [  281]: <-- [4:ATA\r]
May 08 09:29:31.82: [  281]: --> [7:CONNECT]
May 08 09:29:31.82: [  281]: ANSWER: FAX CONNECTION
May 08 09:29:31.88: [  281]: RECV FAX: begin
May 08 09:29:32.02: [  281]: <-- data [23]
May 08 09:29:32.03: [  281]: <-- data [2]
May 08 09:29:33.42: [  281]: --> [7:CONNECT]
May 08 09:29:33.42: [  281]: <-- data [10]
May 08 09:29:33.43: [  281]: <-- data [2]
May 08 09:29:33.85: [  281]: --> [2:OK]
May 08 09:29:33.85: [  281]: <-- [9:AT+FRH=3\r]
May 08 09:29:34.54: [  281]: --> [7:CONNECT]
May 08 09:29:36.47: [  281]: --> [2:OK]
May 08 09:29:36.47: [  281]: REMOTE TSI "05251603533"
May 08 09:29:36.47: [  281]: <-- [9:AT+FRH=3\r]
May 08 09:29:36.50: [  281]: --> [7:CONNECT]
May 08 09:29:36.52: [  281]: --> [2:OK]
May 08 09:29:36.52: [  281]: REMOTE wants 9600 bit/s
May 08 09:29:36.52: [  281]: REMOTE wants page width 1728 pixels in 215 mm
May 08 09:29:36.53: [  281]: REMOTE wants unlimited page length 
May 08 09:29:36.53: [  281]: REMOTE wants 3.85 line/mm
May 08 09:29:36.53: [  281]: REMOTE wants 2-D MR
May 08 09:29:36.53: [  281]: RECV training at v.29 9600 bit/s
May 08 09:29:36.53: [  281]: <-- [10:AT+FRM=96\r]
May 08 09:29:36.83: [  281]: --> [7:CONNECT]
May 08 09:29:38.36: [  281]: RECV: TCF 1841 bytes, 0% non-zero, 1817 zero-run
May 08 09:29:38.36: [  281]: --> [10:NO CARRIER]
May 08 09:29:38.37: [  281]: DELAY 75 ms
May 08 09:29:38.45: [  281]: <-- [9:AT+FTH=3\r]
May 08 09:29:38.52: [  281]: --> [7:CONNECT]
May 08 09:29:38.52: [  281]: <-- data [3]
May 08 09:29:38.53: [  281]: <-- data [2]
May 08 09:29:39.74: [  281]: --> [2:OK]
May 08 09:29:39.74: [  281]: TRAINING succeeded
May 08 09:29:39.75: [  281]: REJECT TSI "05251603533"
May 08 09:29:39.75: [  281]: RECV FAX (00000004): recvq/fax00002.tif from 05251603533, route to <uns
pecified>, 0 pages in 0:07
May 08 09:29:39.82: [  281]: RECV FAX: Permission denied (unacceptable client TSI)
May 08 09:29:39.88: [  281]: <-- [9:AT+FTH=3\r]
May 08 09:29:39.94: [  281]: --> [7:CONNECT]
May 08 09:29:39.95: [  281]: <-- data [3]
May 08 09:29:39.95: [  281]: <-- data [2]
May 08 09:29:41.14: [  281]: --> [2:OK]
May 08 09:29:41.15: [  281]: RECV FAX: bin/faxrcvd "recvq/fax00002.tif" "ttyS1" "00000004" ""
May 08 09:29:45.52: [  281]: RECV FAX: end
May 08 09:29:45.52: [  281]: SESSION END
-------------------------------------------------------------------


Right at the moment I fell like throwing that modem into the garbage can
and bying a new one. It really can be frustating if something won't work
the way you want it to. 

The only thing I cannot understand is the fact that the modem works
correcty when used by Windows. I refuse to believe that Windows can do
anything better than Linux can. So there has to be a way to make this
modem work, hasn't it? ;-)

Bye,

-- 
      \    /
       \/\/olfgang
            		      
                                   ___ 
Wolfgang Mettbach                 (O O)             Uekern 17
wmettbach@metronet.de            {  Y  }            33098 Paderborn (Germany)
===================================#=#========================================
"Imagination is more important than knowledge" (Albert Einstein)