|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: Large number of errors with Hylafax and ZyXEL Omni modem
Hi Shuvam,
Looking at the log below it is kind of obvious that Phase B is your main
problem.
Have you got a spare line you could plug your modem into, just to rule line
noise out(unless you have real bad luck and _both_ your lines are noisy)
Apart from that i imagine it would have to be some sort of configuration
error. Are you using the standard hylafax supplied modem config files for
the Zyxel?
I would seriously consider asking your telco to have your line checked,
even if this costs money as all the phase B errors would be getting expensive.
PS unless of course your modem is really a 1996 USR Sportster that has been
rebadged and sold to you as a Zyxel ;-)
PPS Sportster owners i share your pain!!!
- Robert
At 02:55 3/04/98 +0530, Shuvam Misra wrote:
>| It's hard to make sense of the numbers below(at least for me), i've got a
>| small script "errorstats" which parses xferlog for errors grouping by type.
>|
>| Download from http://www.trump.net.au/~rjc/hylafax/
>
>This script seems to be the same as another one that someone else just
>sent me. I'm including the output from your script. The line to note is
>the "Unspecified Transmit Phase B Error".
>
>Regards, and thanks for your patience,
>Shuvam
>===========================================================================
>Modem: modem
>Total faxes sent: 6611
>
>Error No Rate/1000
>---------------------------------------------------------------------------
---
>Busy signal detected 21 3.2
>Failure to train at 2400 bps or +FMINSP value; Giving up aft 9 1.4
>No response to MPS repeated 3 times; Giving up after 3 attem 60 9.1
>Unspecified Transmit Phase B error 2445 369.8
>COMREC error in transmit Phase B/got DCN 2 0.3
>Unable to set session parameters 6 0.9
>DTE to DCE data underflow 1 0.2
>Failure to train at 2400 bps or +FMINSP value; too many atte 1 0.2
>RSPREC error/got DCN 25 3.8
> 1 0.2
>Unspecified Transmit Phase D error, including +FPHCTO timeou 1 0.2
>RSPREC error/got DCN; Giving up after 3 attempts to send sam 8 1.2
>Unspecified Transmit Phase B error; too many attempts to dia 80 12.1
>No response to EOP repeated 3 times; Giving up after 3 attem 6 0.9
>Unknown problem (check modem power) 5 0.8
>Unable to transmit page (giving up after 3 attempts); too ma 1 0.2
>No response to MPS repeated 3 times 123 18.6
>Unable to set session parameters; Giving up after 3 attempts 1 0.2
>Communication failure during Phase B/C; Giving up after 3 at 1 0.2
>Unspecified Transmit Phase D error, including +FPHCTO timeou 4 0.6
>No response to EOP repeated 3 times 4 0.6
>Unable to transmit page (giving up after 3 attempts); Giving 294 44.5
>Job aborted by user 1 0.2
>No local dialtone 167 25.3
>Communication failure during Phase B/C 3 0.5
>Failure to train at 2400 bps or +FMINSP value 43 6.5
>No carrier detected; too many attempts to dial 9 1.4
>High resolution document is not supported by client, image r 1 0.2
>Unspecified Transmit Phase B error; Giving up after 3 attemp 1 0.2
>Document was encoded with 2DMR, but client does not support 1 0.2
>Unable to transmit page (giving up after 3 attempts) 679 102.7
>Call aborted, from +FK or <CAN> 1 0.2
>No carrier detected 1114 168.5
>---------------------------------------------------------------------------
---
>Total 5119 774.3
>
>Modem: Combined Total
>Total faxes sent: 6611
>
>Error No Rate/1000
>---------------------------------------------------------------------------
---
>Busy signal detected 21 3.2
>Failure to train at 2400 bps or +FMINSP value; Giving up aft 9 1.4
>No response to MPS repeated 3 times; Giving up after 3 attem 60 9.1
>Unspecified Transmit Phase B error 2445 369.8
>COMREC error in transmit Phase B/got DCN 2 0.3
>Unable to set session parameters 6 0.9
>DTE to DCE data underflow 1 0.2
>Failure to train at 2400 bps or +FMINSP value; too many atte 1 0.2
>RSPREC error/got DCN 25 3.8
> 1 0.2
>Unspecified Transmit Phase D error, including +FPHCTO timeou 1 0.2
>RSPREC error/got DCN; Giving up after 3 attempts to send sam 8 1.2
>Unspecified Transmit Phase B error; too many attempts to dia 80 12.1
>No response to EOP repeated 3 times; Giving up after 3 attem 6 0.9
>Unknown problem (check modem power) 5 0.8
>Unable to transmit page (giving up after 3 attempts); too ma 1 0.2
>No response to MPS repeated 3 times 123 18.6
>Unable to set session parameters; Giving up after 3 attempts 1 0.2
>Communication failure during Phase B/C; Giving up after 3 at 1 0.2
>Unspecified Transmit Phase D error, including +FPHCTO timeou 4 0.6
>No response to EOP repeated 3 times 4 0.6
>Unable to transmit page (giving up after 3 attempts); Giving 294 44.5
>Job aborted by user 1 0.2
>No local dialtone 167 25.3
>Communication failure during Phase B/C 3 0.5
>Failure to train at 2400 bps or +FMINSP value 43 6.5
>No carrier detected; too many attempts to dial 9 1.4
>High resolution document is not supported by client, image r 1 0.2
>Unspecified Transmit Phase B error; Giving up after 3 attemp 1 0.2
>Document was encoded with 2DMR, but client does not support 1 0.2
>Unable to transmit page (giving up after 3 attempts) 679 102.7
>Call aborted, from +FK or <CAN> 1 0.2
>No carrier detected 1114 168.5
>---------------------------------------------------------------------------
---
>Total 5119 774.3
>
